EN 13835:2002/A1:2006
(Amendment)Founding - Austenitic cast irons
Founding - Austenitic cast irons
This European Standard specifies the grades and corresponding requirements of austenitic cast irons. These requirements are specified in terms of: - graphite form and metal structure: either flake or spheroidal graphite in an austenitic matrix; - chemical composition: as given for each of the grades; - mechanical properties: obtained from separately cast samples.
Gießereiwesen - Austenitische Gusseisen
Fonderie - Fonte austénitique
Livarstvo – Avstenitna siva litina
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2006
Livarstvo – Avstenitna siva litina
Founding - Austenitic cast irons
Gießereiwesen - Austenitische Gusseisen
Fonderie - Fonte austénitique
Ta slovenski standard je istoveten z: EN 13835:2002/A1:2006
ICS:
77.080.10
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 13835:2002/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2006
ICS 77.080.10
English Version
Founding - Austenitic cast irons
Fonderie - Fonte austénitique Gießereiwesen - Austenitische Gusseisen
This amendment A1 modifies the European Standard EN 13835:2002; it was approved by CEN on 27 April 2006.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the Central Secretariat or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13835:2002/A1:2006: E
worldwide for CEN national Members.
Contents Page
Foreword.3
1 Modification to the Introduction.4
2 Modification to Clause 2 Normative references .4
3 Modification to Table 3.4
4 Modification to Table 4.4
5 Add Clause 11 Inspection documentation .4
6 Modification to Table C.1 .5
7 Add Annex ZA .5
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 97/23/EC .6
Foreword
This document (EN 13835:2002/A1:2006) has been prepared by Technical Committee CEN/TC 190
“Foundry technology”, the secretariat of which is held by DIN.
This Amendment to the European Standard EN 13835:2002 shall be given the status of a national standard,
either by publication of an identical text or by endorsement, at the latest by December 2006, and conflicting
national standards shall be withdrawn at the latest by December 2006.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of a EU Directive.
For relationship with the EU Directive, see informative Annex ZA, which is an integral part of this document.
According to the CEN/CENELEC Internal Reg
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.