iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

prEN 12100

(Main)

Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to bending between supports

Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to bending between supports

This document specifies a test method for the resistance to bending of a test piece, made of a valve assembled together with two pipes and placed between supports, when subjected to internal pressure.
This document is applicable to valves with a polyethylene (PE) body for use with pipes having a nominal outside diameter from greater than 63 mm up to and including 400 mm and intended for the transport of fluids.
When specified in the product standard, this document can be applied to valves of material different than PE.

Kunststoff-Rohrleitungssysteme - Armaturen aus Polyethylen (PE) - Prüfverfahren für den Widerstand gegen Biegen bei Dreipunktbelastung

Dieses Dokument legt ein Prüfverfahren für die Biegefestigkeit eines Prüfkörpers fest, der aus einer mit zwei Rohren zusammengebauten Armatur besteht und zwischen Auflagern angeordnet ist, wenn er einem Innendruck ausgesetzt wird.
Dieses Dokument gilt für Armaturen mit einem Gehäuse aus Polyethylen (PE) für den Einsatz mit Rohren mit einem Nenn-Außendurchmesser größer als 63 mm bis einschließlich 400 mm, die für den Transport von Flüssigkeiten vorgesehen sind.
Wenn in der Produktnorm festgelegt, kann dieses Dokument auf Armaturen aus einem anderen Werkstoff als PE angewendet werden.

Systèmes de canalisations en plastiques - Robinets en polyéthylène (PE) - Méthode d'essai de résistance à la flexion entre supports

Le présent document spécifie une méthode d'essai relative à la résistance à la flexion d’une éprouvette, constituée d’un robinet assemblé à deux tubes et placée entre des supports, lorsqu’elle est soumise à une pression interne.
Le présent document s'applique aux robinets avec un corps en polyéthylène (PE), utilisés avec des tubes présentant un diamètre extérieur nominal supérieur à 63 mm et inférieur ou égal à 400 mm, destinés au transport de fluides.
Lorsque cela est spécifié dans la norme de produit, le présent document peut être appliqué aux robinets en matériau autre que le PE.

Cevni sistemi iz polimernih materialov - Ventili iz polietilena (PE) - Metoda za preskus odpornosti proti upogibanju med podporami

General Information

Status
Not Published
Publication Date
01-May-2025
ICS
23.040.01 - Pipeline components and pipelines in general
Technical Committee
CEN/TC 155 - Plastics piping systems and ducting systems
Drafting Committee
CEN/TC 155/WG 32 - Valves
Current Stage
4060 - Closure of enquiry - Enquiry
Start Date
25-Jan-2024
Due Date
08-Mar-2024
Completion Date
25-Jan-2024
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
Ref Project
oSIST prEN 12100:2024 - Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to bending between supports

Relations

Revises
EN 12100:1997 - Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to bending between supports
Effective Date
22-Jan-2023

Buy Standard

prEN 12100:2024prEN 12100:2024
PreviousNext
Draft
prEN 12100:2024
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN 12100:2024
01-januar-2024
Cevni sistemi iz polimernih materialov - Ventili iz polietilena (PE) - Metoda za
preskus odpornosti proti upogibanju med podporami
Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to
bending between supports
Kunststoff-Rohrleitungssysteme - Armaturen aus Polyethylen (PE) - Prüfverfahren für
den Widerstand gegen Biegen bei Dreipunktbelastung
Systemes de canalisations en plastiques - Robinets en polyéthylene (PE) - Méthode
d'essai de résistance a la flexion entre supports
Ta slovenski standard je istoveten z: prEN 12100
ICS:
23.040.01 Deli cevovodov in cevovodi Pipeline components and
na splošno pipelines in general
83.140.30 Polimerne cevi in fitingi za Plastics pipes and fittings for
snovi, ki niso tekočine non fluid use
oSIST prEN 12100:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 12100:2024

---------------------- Page: 2 ----------------------
oSIST prEN 12100:2024


DRAFT
EUROPEAN STANDARD
prEN 12100
NORME EUROPÉENNE

EUROPÄISCHE NORM

November 2023
ICS 23.040.01 Will supersede EN 12100:1997
English Version

Plastics piping systems - Polyethylene (PE) valves - Test
method for resistance to bending between supports
Systèmes de canalisations en plastiques - Robinets en Kunststoff-Rohrleitungssysteme - Armaturen aus
polyéthylène (PE) - Méthode d'essai de résistance à la Polyethylen (PE) - Prüfverfahren für den Widerstand
flexion entre supports gegen Biegen bei Dreipunktbelastung
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 155.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 12100:2023 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 12100:2024
prEN 12100:2023 (E)
Contents Page
EUROPEAN FOREWORD . 3
INTRODUCTION. 4
1 SCOPE . 5
2 NORMATIVE REFERENCES . 5
3 TERMS AND DEFINITIONS . 5
4 PRINCIPLE . 5
5 APPARATUS . 6
5.1 STATIC UNIAXIAL TESTING MACHINE . 6
5.2 TORQUE MEASURING DEVICE .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
CEN/TS 1566-2:2023(Main)
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 2: Assessment of conformity
SIST-TS CEN/TS 1566-2:2023

This document gives guidance for specifying requirements for the AoC of compounds/formulations, products, joints and assemblies in accordance with the applicable part of EN 1566 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE   A basic test matrix provides an overview of the testing scheme in Annex A.
In conjunction with EN 1566 1 (see European foreword), this document is applicable to solid-wall piping systems made of chlorinated poly(vinyl chloride) (PVC C) intended to be used for or soil and waste discharge systems (low and high temperature):
-   inside buildings (application area code "B");
-   for both inside buildings and buried in ground within the building structure (application area code "BD").

  • Technical specification
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 1455-2:2023(Main)
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 2: Assessment of conformity
SIST-TS CEN/TS 1455-2:2023

This document gives guidance for specifying requirements for the AoC of compounds/formulation, products, joints and assemblies in accordance with the applicable part of EN 1455 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE   A basic test matrix provides an overview of the testing scheme in Annex A.
In conjunction with EN 1455-1 (see European foreword), this document is applicable to solid wall piping systems made of acrylonitrile-butadiene-styrene (ABS) intended to be used for soil and waste discharge (low and high temperature):
-   inside buildings (application area code "B");
-   both inside buildings and buried in ground within the building structure (application area code "BD").

  • Technical specification
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1401-1:2019+A1:2023(Main)
Plastics piping systems for non-pressure underground drainage and sewerage - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system
SIST EN 1401-1:2019+A1:2023

This document specifies the requirements for solid wall pipes with smooth internal and external surfaces, extruded from the same formulation throughout the wall, fittings and the system of unplasticized poly(vinyl chloride) (PVC U) piping systems in the field of non-pressure underground drainage and sewerage:
- buried in ground outside the building structure (application area code "U"), and
- both buried in ground, within the building structure and outside the building (application area code "UD").
NOTE 1   The intended use is reflected in the marking of products by "U" or "UD".
It also specifies the test parameters for the test methods referred to in this document.
NOTE 2   Multilayer pipes with different formulations throughout the wall and foamed core pipes are covered by EN 13476-2 [1].
This document covers a range of nominal sizes, a range of pipes and fittings series and a range of stiffness classes and gives recommendations concerning colours.
NOTE 3   It is the responsibility of the purchaser or specifier to make the appropriate selection from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
It is applicable to PVC U pipes and fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for buried piping systems for non-pressure underground drainage and sewerage.
NOTE 4   Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex C can be used with pipes and fittings conforming to this document, provided they conform to the requirements for joint dimensions given in Clause 7 and to the requirements of Table 16.

  • Standard
    41 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1455-1:2022(Main)
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 1: Specifications for pipes, fittings and the system
SIST EN 1455-1:2023

This document specifies the requirements for solid wall pipes with smooth internal and external surfaces, extruded from the same formulation throughout the wall, fittings and the system of acrylonitrile-butadiene-styrene (ABS) and acrylonitrile-styrene-acrylester (ASA) piping systems intended for soil and waste discharge applications (low and high temperature):
- inside buildings (application area code “B”);
- for both inside buildings and buried in ground within the building structure (application area code “BD”).
NOTE 1 The intended use is reflected in the marking of products by “B” or “BD”.
NOTE 2 Application “B” covers uses above ground inside buildings, or outside buildings fixed onto the wall.
NOTE 3 Pipes and fittings of the pipe series S 25 are intended to be used for application area “B” only.
NOTE 4 For use buried in ground within the building structure are intended only those components (marked with “BD”) with nominal outside diameters equal to or greater than 75 mm.
NOTE 5 EN 476 [5] specifies the general requirements for components used in discharge pipes, drains and sewers for gravity systems. Pipes and fittings conforming to this document fully meet these requirements.
This document is also applicable to ABS and ASA pipes, fittings and the system intended for the following purposes:
- ventilating part of the pipework in association with discharge applications;
- rainwater pipework within the building structure.
It also specifies the test parameters for the test methods that are referred to.
This document covers a range of nominal sizes, a range of pipes and fittings series and gives recommendations concerning colours.
NOTE 6 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
NOTE 7 Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex A can be used with pipes and fittings conforming to this document, provided they conform to the requirements for joint dimensions given in Clause 7 and to the requirements of Table 21.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1566-1:2022(Main)
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: Specifications for pipes, fittings and the system
SIST EN 1566-1:2023

This document specifies the requirements for solid wall pipes with smooth internal and external surfaces, extruded from the same formulation throughout the wall, fittings and the system of chlorinated poly(vinyl chloride) (PVC-C) piping systems intended for soil and waste discharge (low and high temperature):
- inside buildings (application area code “B”);
- for both inside buildings and buried in ground within the building structure (application area code “BD”).
NOTE 1 The intended use is reflected in the marking of products by “B” or “BD”.
NOTE 2 Application “B” covers uses above ground inside buildings, or outside buildings fixed onto the wall.
NOTE 3 Pipes and fittings of the pipe series S 25 are intended to be used for application area “B” only.
NOTE 4 For use buried in ground within the building structure are intended only those components (marked with “BD”) with nominal outside diameters equal to or greater than 75 mm.
NOTE 5 EN 476 [5] specifies the general requirements for components used in discharge pipes, drains and sewers for gravity systems. Pipes and fittings conforming to this document fully meet these requirements.
This document is applicable to PVC-C pipes and fittings and the system intended for the following purposes:
- ventilating part of the pipework in association with discharge applications;
- rainwater pipework within the building structure.
It also specifies the test parameters for the test methods that are referred to.
This document covers a range of nominal sizes, a range of pipe series and gives recommendations concerning colours.
NOTE 6 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
NOTE 7 Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex A can be used with pipes and fittings conforming to this document, provided they conform to the requirements for joint dimensions given in Clause 7 and to the requirements of Table 21.

  • Standard
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 17152-3:2022(Main)
Plastics piping systems for non-pressure underground conveyance and storage of non-potable water - Boxes used for infiltration, attenuation and storage systems - Part 3: Conformity assessment scheme
SIST-TS CEN/TS 17152-3:2023

This document gives guidance for requirements for the assessment of conformity (AoC) of materials, compounds, formulations, products, and assemblies in accordance with the applicable part(s) of EN 17152 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE   Annex B, Table B.1 contains a summary of tests for TT and surveillance monitoring.
In conjunction with EN 17152 1 (see European foreword) this document is applicable to boxes used for infiltration, attenuation and storage systems.

  • Technical specification
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 15874-1:2013/A1:2022(Amendment)
Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 1: General - Amendment 1: Impact test (ISO 15874-1:2013/Amd 1:2022)
SIST EN ISO 15874-1:2013/A1:2022
  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 11295:2022(Main)
Plastics piping systems used for the rehabilitation of pipelines - Classification and overview of strategic, tactical and operational activities (ISO 11295:2022)
SIST EN ISO 11295:2022

This document specifies the steps of the overall process of pipeline rehabilitation, comprising:
—    information on strategic and tactical activities:
a) investigation and condition assessment of the existing pipeline;
b) pipeline rehabilitation planning.
—    information on and requirements for operational activities:
c) project specification;
d) applications of techniques;
e) documentation of the design and application process.
Definitions and classification of families of renovation and trenchless replacement techniques are provided, and their respective features described. Areas of application covered include underground drainage and sewerage networks and underground water and gas supply networks.
The following aspects are not covered by the scope of this document:
—    new construction provided as network extensions;
—    calculation methods to determine, for each viable technique, the characteristics of lining or replacement pipe material needed to secure the desired performance of the rehabilitated pipeline;
—    techniques providing non-structural pressure pipe liners;
—    techniques for local repair.
It is the responsibility of the designer to choose and design the renovation or trenchless replacement pipeline system.

  • Standard
    76 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 1555-7:2021(Main)
Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity
SIST-TS CEN/TS 1555-7:2022

This document gives guidance for the assessment of conformity of compounds, products, joints and assemblies in accordance with the applicable part(s) of EN 1555 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
This document gives recommendations that the quality management system conforms to or is no less stringent than the relevant requirements to EN ISO 9001.
NOTE 1 If certification is involved, the certification and inspection body is preferably compliant with EN ISO/IEC 17065, EN IS0/IEC 17021 or EN ISO/IEC 17020, as applicable.
In conjunction with Parts 1 to 5 of EN 1555 (see Foreword), this document is applicable to polyethylene (PE) plastics piping systems for the supply of gaseous fuels. It is applicable to PE pipes, fittings, and valves, their joints and to joints with components of other materials intended to be used under the following conditions:
a) a maximum operating pressure, MOP, up to and including 10 bar;
b) an operating temperature of 20 °C as reference temperature.
NOTE 2 For other operating temperatures, derating coefficients can be used; see EN 1555-5.

  • Technical specification
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 15877-3:2009/A2:2021(Amendment)
Plastics piping systems for hot and cold water installations - Chlorinated poly(vinyl chloride) (PVC-C) - Part 3: Fittings - Amendment 2 (ISO 15877-3:2009/Amd 2:2021)
SIST EN ISO 15877-3:2009/A2:2021
  • Amendment
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day