CEN ISO/TS 16410-1:2011

Electronic fee collection - Evaluation of equipment for conformity to ISO/TS 17575-3 - Part 1: Test suite structure and test purposes (ISO/TS 16410-1:2011)

ISO/TS 16410-1:2011 specifies the test suite structure (TSS) and test purposes (TP) to evaluate the conformity of Front End and Back End to ISO/TS 17575-3.
The objective of ISO/TS 16410-1:2011 is to provide a basis for conformance tests for the Front End and the Back End in electronic fee collection (EFC) based on autonomous on-board equipment (OBE) to enable interoperability between different equipment supplied by different manufacturers.

Elektronische Gebührenerfassung - Konformitätsevaluierung von Geräten nach ISO/TS 17575-3 - Teil 1: Struktur der Testfolge und Testabsichten (ISO/TS 16410-1:2011)

Perception du télépéage - Évaluation de la conformité de l'équipement à l'ISO/TS 17575-3 - Partie 1: Structure de la suite d'essais et objectifs des essais (ISO/TS 16410-1:2011)

Elektronsko pobiranje pristojbin - Ugotavljanje skladnosti opreme s tehnično specifikacijo ISO/TS 17575-3 - 1. del: Zgradba preskuševalnega niza in namen preskušanja (ISO/TS 16410-1:2011)

Ta tehnična specifikacija bo določala zbirko preskusov za ocenjevanje skladnosti opreme z EFC standardom »Definicija aplikacijskega vmesnika za avtonomne sisteme – Okvirni podatki« (tj. CEN ISO/TS 17575 – 3. del).
Ta del bo vseboval strukturo zbirke preskusov in namene preskusov (»človeku berljiv del«) in uporabo metodologije za določanje preskusov skladnosti, kot je določeno v zbirki standardov TTCN (tj. ISO/IEC 9646). Zajemal bo preskuse za opremo zadnjega dela in opreme prednjega dela (ali kot proksi ali kot pameten klient OBE).
Pristop in struktura bosta analogna z »ocenjevanjem skladnosti za vgrajeno in cestno opremo z EN 15509« (prEN 15876-1, cf verzija poizvedbe CEN).
Oprema za prednji in zadnji del bo po vsej verjetnosti predmet dodatnega preskušanja fizične in okoljske vzdržljivosti, zagotavljanja kakovosti in nadzora pri proizvodnji, integracije plačilne točke, kot del tovarne, lokacije in preskušanja sprejemljivosti sistema. Definicija teh preskusov je zunaj okvira tega standarda.
Preskusi za ocenjevanje skladnosti z nedelovne zahteve, kot so natančnost senzorjev, stopnje delovanja in moči računanja, so zunaj področja uporabe tega standarda. Zajeti bi morali biti z ocenjevanjem skladnosti ustreznega profila standarda.

General Information

• Status: Withdrawn
• Publication Date: 14-Oct-2011
• Withdrawal Date: 12-Dec-2017
• ICS: 03.220.20 - Road transport
• ICS: 35.240.60 - IT applications in transport
• Technical Committee: CEN/TC 278 - Road transport and traffic telematics
• Drafting Committee: CEN/TC 278/WG 1 - Electronic fee collection and access control (EFC)
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 13-Dec-2017
• Directive: 2004/52/EC - Interoperability of electronic road toll systems in the Community
• Mandate: M/338 - Standardisation mandate to CEN, CENELEC and ETSI in support of interoperabilty of electonic road toll systems in the community
• Ref Project: SIST-TS CEN ISO/TS 16410-1:2011 - Electronic fee collection - Evaluation of equipment for conformity to ISO/TS 17575-3 - Part 1: Test suite structure and test purposes (ISO/TS 16410-1:2011)

Relations

• Replaced By: EN ISO 16410-1:2017 - Electronic fee collection - Evaluation of equipment for conformity to ISO 17575-3 - Part 1: Test suite structure and test purposes (ISO 16410-1:2017)
• Effective Date: 20-Dec-2017

Standards Content (Sample)

SLOVENSKI STANDARD
01-december-2011
(OHNWURQVNRSRELUDQMHSULVWRMELQ8JRWDYOMDQMHVNODGQRVWLRSUHPHVWHKQLþQR
VSHFLILNDFLMR,6276GHO=JUDGEDSUHVNXãHYDOQHJDQL]DLQQDPHQ
SUHVNXãDQMD,6276
Electronic fee collection - Evaluation of equipment for conformity to ISO/TS 17575-3 -
Part 1: Test suite structure and test purposes (ISO/TS 16410-1:2011)
Elektronische Gebührenerfassung - Konformitätsevaluierung von Equipment zur CEN
ISO/TS 17575-3 - Teil 1: Struktur der Testfolge und Testabsichten (ISO/TS 16410-
1:2011)
Perception du télépéage - Évaluation de la conformité de l'équipement à l'ISO/TS 17575-
3 - Partie 1: Structure de la suite d'essais et objectifs des essais (ISO/TS 16410-1:2011)
Ta slovenski standard je istoveten z: CEN ISO/TS 16410-1:2011
ICS:
03.220.20 Cestni transport Road transport
35.240.60 Uporabniške rešitve IT v IT applications in transport
transportu in trgovini and trade
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

TECHNICAL SPECIFICATION
CEN ISO/TS 16410-1
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
October 2011
ICS 35.240.60; 03.220.20
English Version
Electronic fee collection - Evaluation of equipment for conformity
to ISO/TS 17575-3 - Part 1: Test suite structure and test
purposes (ISO/TS 16410-1:2011)
Perception du télépéage - Évaluation de la conformité de Elektronische Gebührenerfassung -
l'équipement à l'ISO/TS 17575-3 - Partie 1: Structure de la Konformitätsevaluierung von Equipment zur CEN ISO/TS
suite d'essais et objectifs des essais (ISO/TS 16410- 17575-3 - Teil 1: Struktur der Testfolge und Testabsichten
1:2011) (ISO/TS 16410-1:2011)
This Technical Specification (CEN/TS) was approved by CEN on 15 August 2011 for provisional application.

The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.

CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN ISO/TS 16410-1:2011: E
worldwide for CEN national Members.

Contents Page
Foreword .3
Foreword
This document (CEN ISO/TS 16410-1:2011) has been prepared by Technical Committee CEN/TC 278 “Road
transport and traffic telematics”, the secretariat of which is held by NEN, in collaboration with Technical
Committee ISO/TC 204 “Intelligent transport systems”.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Croatia, Cyprus,
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.
TECHNICAL ISO/TS
SPECIFICATION 16410-1
First edition
2011-10-15
Electronic fee collection — Evaluation
of equipment for conformity to
ISO/TS 17575-3 —
Part 1:
Test suite structure and test purposes
Perception du télépéage — Évaluation de la conformité de l'équipement
à l'ISO/TS 17575-3 —
Partie 1: Structure de la suite d'essais et objectifs des essais

Reference number
ISO/TS 16410-1:2011(E)
©
ISO 2011
ISO/TS 16410-1:2011(E)
©  ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56  CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved

ISO/TS 16410-1:2011(E)
Contents Page
Foreword . iv
Introduction . v
1  Scope . 1
2  Normative references . 2
3  Terms and definitions . 2
4  Abbreviated terms . 4
5  Test Suite Structure (TSS) . 4
5.1  Structure . 4
5.2  Reference to conformance test specifications . 6
5.3  Test Purposes (TP) . 6
5.4  Conformance test report . 7
Annex A (normative) Test Purposes (TP) for Front End . 8
Annex B (normative) Test purposes (TP) for Back End . 92
Annex C (normative) Data Structures . 124
Annex D (normative) PCTR for Front End . 135
Annex E (normative) PCTR for Back End . 141
Bibliography . 147

ISO/TS 16410-1:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
In other circumstances, particularly when there is an urgent market requirement for such documents, a
technical committee may decide to publish other types of document:
— an ISO Publicly Available Specification (ISO/PAS) represents an agreement between technical experts in
an ISO working group and is accepted for publication if it is approved by more than 50 % of the members
of the parent committee casting a vote;
— an ISO Technical Specification (ISO/TS) represents an agreement between the members of a technical
committee and is accepted for publication if it is approved by 2/3 of the members of the committee casting
a vote.
An ISO/PAS or ISO/TS is reviewed after three years in order to decide whether it will be confirmed for a
further three years, revised to become an International Standard, or withdrawn. If the ISO/PAS or ISO/TS is
confirmed, it is reviewed again after a further three years, at which time it must either be transformed into an
International Standard or be withdrawn.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO/TS 16410-1 was prepared by Technical Committee ISO/TC 204, Intelligent transport systems, in
collaboration with Technical Committee CEN/TC 278, Road Transport and Traffic Telematics.
ISO/TS 16410 consists of the following parts, under the general title Electronic fee collection — Evaluation of
equipment for conformity to ISO/TS 17575-3:
— Part 1: Test suite structure and test purposes
— Part 2: Abstract test suites

iv © ISO 2011 – All rights reserved

ISO/TS 16410-1:2011(E)
Introduction
This part of ISO 16410 is part of a set of standards that supports interoperability of autonomous EFC-systems,
which includes ISO/TS 17575 parts 1 to 4 that define the EFC context data, their charge reports and their use
of communication infrastructure.
Within the suite of EFC standards this conformance evaluation procedure defines the process and tests for
conformity evaluation of Front End and Back End that comply with the requirements in ISO/TS 17575-3.
This part of ISO 16410 is intended to
 assess Front End and Back End capabilities,
 assess Front End and Back End behaviour,
 serve as a guide for Front End and Back End conformance evaluation and type approval,
 achieve comparability between the results of the corresponding tests applied in different places at
different times, and
 facilitate communications between parties.
This part of ISO 16410 is based on
 ISO/TS 17575-3, and
 the ISO 9646 family of standards on conformance test methodology.

TECHNICAL SPECIFICATION ISO/TS 16410-1:2011(E)

Electronic fee collection — Evaluation of equipment for
conformity to ISO/TS 17575-3 —
Part 1:
Test suite structure and test purposes
1 Scope
This part of ISO/TS 16410 specifies the test suite structure (TSS) and test purposes (TP) to evaluate the
conformity of Front End and Back End to ISO/TS 17575-3.
The objective of this part of ISO/TS 16410 is to provide a basis for conformance tests for the Front End and
the Back End in Electronic Fee Collection (EFC) based on autonomous on-board equipment (OBE) to enable
interoperability between different equipment supplied by different manufacturers.
Autonomous OBE operates without relying on dedicated road-side infrastructure by employing wide-area
technologies such as Global Navigation Satellite Systems (GNSS) and Cellular Communications Networks
(CN). These EFC systems are referred to by a variety of names. Besides the terms autonomous systems and
GNSS/CN systems, also the terms GPS/GSM systems and wide-area charging systems are in use.
Autonomous systems use satellite positioning, often combined with additional sensor technologies such as
gyroscopes, odometers, and accelerometers, to localise the vehicle and to find its position on a map
containing the charged geographic objects, such as charged roads or charged areas. From the charged
objects, the vehicle characteristics, the time of day and other data that are relevant for describing road use,
the tariff and ultimately the road usage fee is determined.
For more information regarding autonomous systems, please refer to ISO/TS 17575-3.
Testing of the following behaviours and functionalities is outside of the scope of this part of ISO/TS 16410:
 dynamic behaviour, i.e. sequence of messages and triggering events that must be exchanged/happen to
fulfil certain charging scenarios;
 profiles and business logic built on top of par
...