EN ISO 26203-2:2011

Metallic materials - Tensile testing at high strain rates - Part 2: Servo-hydraulic and other test systems (ISO 26203-2:2011)

ISO 26203-2:2011 gives requirements for the testing of metallic materials. Only examples for testing flat geometries are given; however, other geometries can be tested. The area of application spans a range of strain rates from 10-2 s-1 to 103 s-1. Tests are carried out between 10 °C and 35 °C and, unless otherwise specified, using a servo-hydraulic-type test system.

Metallische Werkstoffe - Zugversuch bei hohen Dehngeschwindigkeiten - Teil 2: Servohydraulische und andere Systeme (ISO 26203-2:2011)

Dieser Teil der ISO 26203 gilt für das Prüfen von Blechen aus metallischen Werkstoffen. Der Anwendungs-bereich erstreckt sich über einen Dehnratenbereich von 10–2 s–1 bis 103 s–1. Falls nicht anders festgelegt, können die Prüfungen zwischen 10 °C und 35 °C unter Anwendung einer servohydraulischen Prüfmaschine durchgeführt werden.
ANMERKUNG   Messungen bei Dehnraten unter 10–2 s–1 können unter Anwendung von Prüfmaschinen für quasistatische Prüfungen durchgeführt werden.
ANMERKUNG   Siehe ESIS P7 [1] und FAT Richtlinie [3] für andere Prüfgeometrien als in 6.1 und in Anhang B darge¬stellt.

Matériaux métalliques - Essai de traction à vitesses de déformation élevées - Partie 2: Systèmes d'essai servo-hydrauliques et autres systèmes d'essai (ISO 26203-2:2011)

L'ISO 26203-2:2011 spécifie les exigences pour les essais réalisés sur des matériaux métalliques. Seuls des exemples pour les essais sur des éprouvettes plates sont donnés; cependant, d'autres géométries peuvent être essayées. Le domaine d'application couvre une plage de vitesses de déformation comprise entre 10-2 s-1 et 103 s-1. Les essais doivent être réalisés, sauf spécification contraire, entre 10 °C et 35 °C, à l'aide d'un système d'essai de type servo-hydraulique.

Kovinski materiali - Natezno preskušanje pri velikih hitrostih deformacije - 2. del: Servohidravlični in drugi preskusni sistemi (ISO 26203-2:2011)

Ta del ISO 26203 podaja zahteve za preskušanje kovinskih materialov. Podani so samo primeri preskušanja ploščatih geometrij, preskušajo pa se lahko tudi druge geometrije. Področje uporabe obsega razpon nateznih hitrosti med 10-2 s-1 do 103 s-1. Preskusi se izvajajo pri temperaturi med 10 °C in 35 °C in, če ni navedeno drugače, z uporabo servohidravličnega preskusnega sistema.

General Information

• Status: Published
• Publication Date: 14-Oct-2011
• ICS: 77.040.10 - Mechanical testing of metals
• Technical Committee: ECISS/TC 101 - Test methods for steel (other than chemical analysis)
• Drafting Committee: ECISS/TC 101 - Test methods for steel (other than chemical analysis)
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Completion Date: 15-Sep-2016
• Ref Project: SIST EN ISO 26203-2:2012 - Metallic materials - Tensile testing at high strain rates - Part 2: Servo-hydraulic and other test systems (ISO 26203-2:2011)

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 26203-2:2012
01-januar-2012
.RYLQVNLPDWHULDOL1DWH]QRSUHVNXãDQMHSULYHOLNLKKLWURVWLKGHIRUPDFLMHGHO
6HUYRKLGUDYOLþQLLQGUXJLSUHVNXVQLVLVWHPL,62
Metallic materials - Tensile testing at high strain rates - Part 2: Servo-hydraulic and other
test systems (ISO 26203-2:2011)
Metallische Werkstoffe - Zugversuch bei hohen Dehngeschwindigkeiten - Teil 2:
Servohydraulische und andere Systeme (ISO 26203-2:2011)
Matériaux métalliques - Essai de traction à vitesses de déformation élevées - Partie 2:
Systèmes d'essai servo-hydrauliques et autres systèmes d'essai (ISO 26203-2:2011)
Ta slovenski standard je istoveten z: EN ISO 26203-2:2011
ICS:
77.040.10 Mehansko preskušanje kovin Mechanical testing of metals
SIST EN ISO 26203-2:2012 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 26203-2:2012

---------------------- Page: 2 ----------------------

SIST EN ISO 26203-2:2012


EUROPEAN STANDARD
EN ISO 26203-2

NORME EUROPÉENNE

EUROPÄISCHE NORM
October 2011
ICS 77.040.10
English Version
Metallic materials - Tensile testing at high strain rates - Part 2:
Servo-hydraulic and other test systems (ISO 26203-2:2011)
Matériaux métalliques - Essai de traction à vitesses de Metallische Werkstoffe - Zugversuch bei hohen
déformation élevées - Partie 2: Systèmes d'essai servo- Dehngeschwindigkeiten - Teil 2: Servohydraulische und
hydrauliques et autres systèmes d'essai (ISO 26203- andere Systeme (ISO 26203-2:2011)
2:2011)
This European Standard was approved by CEN on 17 September 2011.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 26203-2:2011: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 26203-2:2012
EN ISO 26203-2:2011 (E)
Contents Page
Foreword .3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 26203-2:2012
EN ISO 26203-2:2011 (E)
Foreword
This document (EN ISO 26203-2:2011) has been prepared by Technical Committee ISO/TC 164 "Mechanical
testing of metals" in collaboration with Technical Committee ECISS/TC 101 “Test methods for steel (other
than chemical analysis)” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by April 2012, and conflicting national standards shall be withdrawn at the
latest by April 2012.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 26203-2:2011 has been approved by CEN as a EN ISO 26203-2:2011 without any
modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 26203-2:2012

---------------------- Page: 6 ----------------------

SIST EN ISO 26203-2:20
...