prEN 14215
(Main)Textile floor coverings - Specification of rugs and runners
Textile floor coverings - Specification of rugs and runners
This document specifies requirements for woven, tufted, knitted, needled, flocked, bonded, hand-tufted rugs and runners, including a level of use intensity and luxury.
This document is not applicable to hand-knotted rugs and runners, to barrier mats or to bathroom rugs.
Textile Bodenbeläge - Klassifizierung von maschinengefertigten Teppichen und Läufern
Dieses Dokument legt Anforderungen an gewebte, getuftete, gewirkte, genadelte, beflockte, geklebte, handgetuftete Teppiche und Läufer einschließlich eines Grads der Beanspruchung und des Luxus fest.
Dieses Dokument gilt nicht für handgeknüpfte Teppiche und Läufer, Eingangsmatten oder Badteppiche.
Revêtements de sol textiles - Spécification des carpettes et passages
Le présent document spécifie les exigences qui s’appliquent aux carpettes et passages tissés, touffetés, tricotés, aiguilletés, floqués, nappés, touffetés mains, et définit un niveau d’intensité d’usage ainsi que la classe de confort du produit.
Ce document ne s’applique pas aux carpettes et aux passages faits main, tapis de propreté ou carpettes de bain.
Tekstilne talne obloge - Specifikacija preprog in tekačev
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-april-2024
Tekstilne talne obloge - Specifikacija preprog in tekačev
Textile floor coverings - Specification of rugs and runners
Textile Bodenbeläge - Klassifizierung von maschinengefertigten Teppichen und Läufern
Revêtements de sol textiles - Spécification des carpettes et passages
Ta slovenski standard je istoveten z: prEN 14215
ICS:
97.150 Talne obloge Floor coverings
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2024
ICS 97.150 Will supersede EN 14215:2018
English Version
Textile floor coverings - Specification of rugs and runners
Revêtements de sol textiles - Classification des Textile Bodenbeläge - Klassifizierung von
carpettes et passages à velours manufacturés maschinengefertigten Teppichen und Läufern
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 134.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 14215:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Identification requirements . 5
Table 1 — Identification characteristics . 6
5 Basic requirements . 6
Table 2 — Basic requirements . 6
6 Level of use intensity . 7
Table 3 — Level for use intensity – Change in appearance – Requirements . 7
7 Luxury rating requirements . 8
Table 4 — Luxury rating class . 8
8 Additional performance properties . 8
Table 5 — Additional performance properties . 8
9 Report . 8
Annex A (normative) Criteria for the assessment of stair suitability . 9
Table A.1 — Stair suitability for loop pile runners . 9
Table A.2 — Stair suitability for cut pile runners . 10
Table A.3 — Tuft withdrawal force requirements . 11
Table A.4 — Stair suitability for runners without pile . 11
Table A.5 — Stair suitability for flat needled runners . 11
Table A.6 — Stair suitability for pile needled runners . 12
Annex B (normative) Summary test report . 13
Table B.1 — Test report . 13
Table B.2.1 — Ref 1 – Type of manufacture . 14
Table B.2.2 — Ref 2 – Type of surface (combinations are possible) . 14
Table B.2.3 — Ref 3 – Type of primary backing (combinations are possible) . 14
Table B.2.4 — Ref 4 – Type of additional backing (combinations are possible) . 15
Table B.2.5 — Ref 5 – Type of pile fibre composition (combinations are possible) . 17
Table B.2.6 — Ref 6 – Type of colouring/patterning . 18
Bibliography . 19
European foreword
This document (prEN 14215:2024) has been prepared by Technical Committee CEN/TC 134 “Resilient,
textile, laminate and modular mechanical locked floor coverings”, the secretariat of which is held by NBN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 14215:2018.
— Title of document: Classification of rugs and runners has been changed into Specification of machine-
made rugs and runners ; Deleted “machine-made” from title.
— Clause 1 Scope: classification has been changed into level of use intensity.
— Clause 2 Normative references: general update and included publication dates of referred norms.
— Clause 3 Terms and definitions: definitions of abbreviations deleted, added definitions of needled
floor coverings.
— Table 1 Characteristics: tolerances aligned with Table 2 of EN 1307:2014+A3:2018. Changed
footnote of table.
— Clause 4 Identification requirements: aligned with EN 1307:2014+A3:2018.
— Clause 5 Table 2 Basic requirements: modified basic requirements.
— Clause 6 Classification for level of use intensity: classification scheme changed in Level of use
intensity with suitability for areas of use requirements.
— Table 4 Luxury rating classes: requirements aligned with Table 18 of EN 1307:2014+A3:2018.
— Annex A Criteria for the assessment of stair suitability: aligned with Annex C of
EN 1307:2014+A3:2018.
1 Scope
This document specifies requirements for woven, tufted, knitted, needled, flocked, bonded, hand-tufted
rugs and runners, including a level of use intensity and luxury.
This document is not applicable to hand-knotted rugs and runners, to barrier mats or to bathroom rugs.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 984:2001, Textile floor coverings – Determination of the mass per unit area of the use surface of needled
floor coverings
EN 14159:2014, Textile floor coverings - Requirements for tolerances on (linear) dimensions of rugs,
runners, carpet tiles and wall-to-wall carpet and for tolerances on pattern repeat
EN 14499, Textile floor coverings – Minimum requirements for carpet underlays
EN ISO 105-B02:2014, Textiles - Tests for colour fastness - Part B02: Colour fastness to artificial light: Xenon
arc fading lamp test (ISO 105-B02:2014)
EN ISO 105-E01:2013, Textiles - Tests for colour fastness - Part E01: Colour fastness to water (ISO 105-
E01:2013)
EN ISO 105-X12:2016, Textiles - Tests for colour fastness - Part X12: Colour fastness to rubbing (ISO 105-
X12:2016)
EN ISO 9405:2017, Textile floor coverings - Assessment of changes in appearance (ISO 9405:2015)
ISO 1763:2020, Textile floor coverings - Determination of number of tufts and/or loops per unit length and
per unit area
ISO 1765:1986, Machine-made textile floor coverings - Determination of thickness
ISO 1766:1999, Textile floor coverings - Determination of thickness of pile above the substrate
ISO 2424:2007, Textile floor coverings - Vocabulary
ISO 4919:2012, Carpets - Determination of tuft withdrawal force
ISO 8543:2020, Textile floor coverings - Methods for determination of mass
ISO 10361:2015, Textile floor coverings – Production of changes in appearance by means of Vettermann
drum and hexapod tumbler tester
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 2424:2007 and the following
apply.
3.1
nominal value
value stated by the manufacturer
3.2
flat needled floor covering type A1
flat needled homogeneous floor covering
flat needled floor covering with one visible layer
Note 1 to entry: Layers such as secondary backing are also taken into consideration for the determination of the
number of layers.
3.3
flat needled floor covering type A2
flat needled floor covering with more than one visible layer, the bonding compound of which does not
reach the top of the use surface
Note 1 to entry: Layers such as secondary backing are also taken into consideration for the determination of the
number of layers.
3.4
flat needled floor covering type A3
flat needled floor covering with more than one visible layer the bonding compound of which is present
throughout its thickness
Note 1 to entry: Layers such as secondary backing are also taken into consideration for the determination of the
number of layers.
3.5
pile needled floor coverings type B1
needled textile floor covering with pile in which the use-surface is composed of entangled fibres bonded
together by a mechanical and a chemical process, of which the mechanical bonding system is a
consolidation of a batt of fibres through entanglement by multiple penetrations of barbed needles in one
or more (visible) layers and needles are used for structuring this pre-needled felting material, the use
surface is either a geometric or linear design, a velours or a rib pattern
3.6
pile needled floor coverings type B2
needled textile floor covering with pile in which the use-surface is composed of entangled fibres bonded
together by a mechanical and a chemical process, of which the mechanical bonding system is a
consolidation of a batt of fibres through entanglement by multiple penetrations of barbed needles in one
or more (visible) layers and mechanically brushing machines are being used for structuring this pre-
needled felting material, resulting in a roughened surface with relatively long and coarse protruding
fibres and for which the bonding system is applied to the back
3.7
pile needled floor coverings type B3
needled textile floor covering in which the use-surface is composed of fibre spheres bonded together by
a mechanical and a chemical process, the chemical bonding system being incorporated in the backing
4 Identification requirements
This clause specifies the requirements for the identification of the product and tolerances for the
identifying properties.
The following information shall be provided in accordance with the terms and definitions according to
ISO 2424:2007 and in accordance with the list of references in Annex B:
— commercial name,
— composition of use surface (see Annex B, Table B.2.5),
— type of manufacture (see Annex B, Table B.2.1),
— type of surface (see Annex B, Table B.2.2),
— type of primary backing, if applicable (see Annex B, Table B.2.3),
— type of additional backing if applicable(see Annex B, Table B.2.4).
The nominal values of the characteristics shall be declared as listed in Table 1 using the test methods
specified therein. The tolerances of the characteristics shall be in accordance with Table 1.
Table 1 — Identification characteristics
Characteristics Applicable for
(X means applicable)
Tolerances
Test method /
(to nominal
Carpets Carpets
Reference Flat Pile
value)
with pile without needled needled
pile
Fibre composition of use-surface Table B.2.5 Ref 5. X X X X
Dim
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.