Bitumen and bituminous binders - Determination of complex shear modulus and phase angle - Dynamic Shear Rheometer (DSR)

This European standard specifies a number of methods using a dynamic shear rheometer (DSR) capable of measuring the rheological properties of bituminous binders. The procedure involves determining the complex shear modulus and phase angle of binders over a range of test frequencies and test temperatures when tested in oscillatory shear.
From the test, the norm of the complex shear modulus, IG*I, and its phase angle, δ, at a given temperature and frequency can be calculated, as well as the components G', G'', J' and J'' of the complex shear modulus and of the complex compliance.
This method is applicable to un-aged, aged and recovered bituminous binders, cut-backs and bituminous binders stabilised from emulsions.
WARNING — The use of this European Standard can involve hazardous materials, operations and equipment. This European Standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this European Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use.

Bitumen und bitumenhaltige Bindemittel - Bestimmung des komplexen Schermoduls und des Phasenwinkels - Dynamisches Scherrheometer (DSR)

Diese Europäische Norm legt eine Reihe von Verfahren fest, bei denen ein dynamisches Scherrheometer (DSR) zur Anwendung kommt, mit dem die rheologischen Eigenschaften von bitumenhaltigen Bindemitteln gemessen werden können. Die Durchführung schließt die Bestimmung des komplexen Schermoduls und des Phasenwinkels von Bindemitteln über einen Bereich von Prüffrequenzen und Prüftemperaturen bei der Prü-fung im Oszillations-Modus ein. Aus der Prüfung können sowohl der Betrag des komplexen Schermoduls, *G, und der zugehörige Phasen-winkel, δ, für eine gegebene Temperatur und Frequenz als auch die Komponenten G′, G′′, J′ und J′′ des komplexen Schermoduls und der komplexen Nachgiebigkeit berechnet werden. Dieses Verfahren ist anwendbar für nicht gealterte, gealterte und rückgewonnene bitumenhaltige Bindemittel, verschnittene oder gefluxte Bindemittel sowie aus Emulsionen rückgewonnene, stabilisierte Bindemittel. WARNUNG — Die Anwendung dieser Europäischen Norm kann den Umgang mit gefährlichen Substanzen und Ausrüstungsteilen und die Ausführung gefährlicher Arbeitsgänge einschließen. Diese Europäischen Norm erhebt nicht den Anspruch, alle mit ihrer Anwendung verbundenen Sicherheitsprobleme anzusprechen. Es liegt in der Verantwortung des Anwenders dieser Europäischen Norm, geeignete Verhaltensregeln für den Arbeits- und Gesundheitsschutz festzulegen und vor der Anwendung zu klären, ob einschränkende Vorschriften zu berücksichtigen sind.

Bitumes et liants bitumineux - Détermination du module complexe en cisaillement et de l'angle de phase - Rhéomètre à cisaillement dynamique (DSR)

La présente Norme européenne traite de plusieurs méthodes faisant appel à un rhéomètre à cisaillement dynamique (DSR) capable de mesurer certaines caractéristiques rhéologiques de liants bitumineux. La procédure repose sur la détermination du module complexe en cisaillement et de l’angle de phase de liants sur une plage de fréquences et de températures d’essai, lorsqu’ils sont testés en cisaillement oscillatoire. À partir des résultats de cet essai, il est possible de calculer la norme du module complexe en cisaillement, IG*I, et son angle de phase, , à une température et à une fréquence données, ainsi que les composantes G', G'', J' et J'' du module complexe en cisaillement et de la complaisance complexe. Cette méthode est applicable aux liants bitumineux neufs, vieillis et récupérés, ainsi qu’aux liants bitumineux fluidifiés et aux liants bitumineux stabilisés à partir d’une émulsion. AVERTISSEMENT — L'utilisation de la présente Norme européenne peut impliquer l'intervention de produits, d'opérations et d'équipements à caractère dangereux. Cette Norme européenne n'est pas censée aborder tous les problèmes de sécurité concernés par son usage. Il est de la responsabilité de son utilisateur d'établir des règles d'hygiène et de sécurité appropriées et de déterminer l'applicabilité des restrictions réglementaires avant utilisation.

Bitumen in bitumenska veziva - Ugotavljanje kompleksnega strižnega modula in faznega kota - Dinamični strižni reometer (DSR)

Ta evropski standard določa številne metode, pri katerih se uporablja dinamični strižni reometer (DSR) za ugotavljanje reoloških lastnosti bitumenskih veziv. Postopek zajema ugotavljanje kompleksnega strižnega modula in faznega kota veziv za različne frekvence preskušanja in temperature pri preskušanju pod oscilatornimi strižnimi pogoji. Na podlagi preskusa je mogoče izračunati normo kompleksnega strižnega modula, IG*I, in njegovega faznega kota, δ, pri dani temperaturi in frekvenci ter komponente G', G'', J' in J'' kompleksnega strižnega modula in kompleksne skladnosti. Ta metoda se uporablja za nestarana, starana in ponovno pridobljena bitumenska veziva, rezana bitumenska veziva in bitumenska veziva, stabilizirana iz emulzij.

General Information

Status
Withdrawn
Publication Date
15-May-2012
Withdrawal Date
04-Jul-2023
Current Stage

Relations

Buy Standard

Standard
EN 14770:2012
English language
15 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Bitumen und bitumenhaltige Bindemittel - Bestimmung des komplexen Schermoduls und des Phasenwinkels - Dynamisches Scherrheometer (DSR)Bitumes et liants bitumineux - Détermination du module complexe en cisaillement et de l'angle de phase - Rhéomètre à cisaillement dynamique (DSR)Bitumen and bituminous binders - Determination of complex shear modulus and phase angle - Dynamic Shear Rheometer (DSR)91.100.50Veziva. Tesnilni materialiBinders. Sealing materials75.140Voski, bitumni in drugi naftni proizvodiWaxes, bituminous materials and other petroleum productsICS:Ta slovenski standard je istoveten z:EN 14770:2012SIST EN 14770:2012en,fr,de01-september-2012SIST EN 14770:2012SLOVENSKI
STANDARDSIST EN 14770:20051DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14770
May 2012 ICS 75.140; 91.100.50 Supersedes EN 14770:2005English Version
Bitumen and bituminous binders - Determination of complex shear modulus and phase angle - Dynamic Shear Rheometer (DSR)
Bitumes et liants bitumineux - Détermination du module complexe en cisaillement et de l'angle de phase - Rhéomètre à cisaillement dynamique (DSR)
Bitumen und bitumenhaltige Bindemittel - Bestimmung des komplexen Schermoduls und des Phasenwinkels - Dynamisches Scherrheometer (DSR) This European Standard was approved by CEN on 7 April 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 14770:2012: ESIST EN 14770:2012

Temperature verification procedure . 12Annex B (informative)
Determining equilibration time . 13Annex C (informative)
Determination of the viscoelastic linear range . 14Bibliography . 15 SIST EN 14770:2012

From the test, the norm of the complex shear modulus, IG*I, and its phase angle, /, at a given temperature and frequency can be calculated, as well as the components G', G'', J' and J'' of the complex shear modulus and of the complex compliance. This method is applicable to un-aged, aged and recovered bituminous binders, cut-backs and bituminous binders stabilised from emulsions. WARNING — The use of this European Standard can involve hazardous materials, operations and equipment. This European Standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this European Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations prior to use. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1427, Bitumen and bituminous binders — Determination of softening point — Ring and Ball method EN 12594, Bitumen and bituminous binders — Preparation of tests samples 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 norm of the complex shear modulus IG*I ratio of peak stress to the peak strain in harmonic sinusoidal oscillation 3.2 phase angle / phase difference between stress and strain in harmonic oscillation 3.3 norm of the complex compliance IJ*I
ratio of the peak strain to the peak stress in harmonic sinusoidal oscillation Note 1 to entry: The real parts of the complex shear modulus IG*I and the complex shear compliance IJ*I
are respectively G´ and J´ and are associated with the elastic part of material behaviour which represents energy stored during a shear cycle. They are complex shear modulus or complex shear compliance multiplied with cosine of phase angle expressed in degrees. The imaginary parts of the complex shear modulus and the complex shear compliance are respectively G´´ and J´´ and are associated with the viscous part of material behaviour which represents energy dissipated during a shear cycle. They are complex shear modulus or complex shear compliance multiplied with sine of phase angle expressed in degrees. SIST EN 14770:2012
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.