EN ISO 21182:2006
(Main)Light conveyor belts - Determination of the coefficient of friction (ISO 21182:2005)
Light conveyor belts - Determination of the coefficient of friction (ISO 21182:2005)
ISO 21182:2005 specifies test methods for determining the dynamic and static coefficients of friction for light conveyor belts according to ISO 21183-1.
Leichte Fördergurte - Bestimmung des Reibwertes (ISO 21182:2005)
Diese Europäische Norm beschreibt Prüfverfahren für die Bestimmung des dynamischen und statischen Reibwertes für leichte Fördergurte, wie sie in ISO 21183-1 beschrieben sind.
Courroies transporteuses légères - Détermination du coefficient de frottement (ISO 21182:2005)
L'ISO 21182:2005 spécifie les méthodes d'essai permettant de déterminer les coefficients de frottement dynamique et statique des courroies transporteuses légères, telles que décrites dans l'ISO 21183-1.
Naprave za kontinuirni transport – Lahki trakovi tračnih transporterjev – Ugotavljanje koeficienta trenja (ISO 21182:2005)
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Light conveyor belts - Determination of the coefficient of friction (ISO 21182:2005)Courroies transporteuses légeres - Détermination du coefficient de frottement (ISO 21182:2005)Leichte Fördergurte - Bestimmung des Reibwertes (ISO 21182:2005)Ta slovenski standard je istoveten z:EN ISO 21182:2006SIST EN
ISO 21182:2007en53.040.20Deli za transporterjeComponents for conveyorsICS:SLOVENSKI
STANDARDSIST EN
ISO 21182:200701-april-2007
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN ISO 21182November 2006ICS 53.040.10Supersedes EN 1724:1998
English VersionLight conveyor belts - Determination of the coefficient of friction(ISO 21182:2005)Courroies transporteuses légères - Détermination ducoefficient de frottement (ISO 21182:2005)Leichte Fördergurte - Bestimmung des Reibwertes (ISO21182:2005)This European Standard was approved by CEN on 21 October 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2006 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN ISO 21182:2006: E
Endorsement notice The text of ISO 21182:2005 has been approved by CEN as EN ISO 21182:2006 without any modifications.
Reference numberISO 21182:2005(E)© ISO 2005
INTERNATIONAL STANDARD ISO21182First edition2005-11-01Light conveyor belts — Determination of the coefficient of friction Courroies transporteuses légères — Détermination du coefficient de frottement
ISO 21182:2005(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
©
ISO 2005 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 • CH-1211 Geneva 20 Tel.
+ 41 22 749 01 11 Fax
+ 41 22 749 09 47 E-mail
copyright@iso.org Web
www.iso.org Published in Switzerland
ii
ISO 21182:2005(E) © ISO 2005 – All rights reserved
iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 21182 was prepared by Technical Committee ISO/TC 41, Pulleys and belts (including veebelts), Subcommittee SC 3, Conveyor belts. This International Standard is based on EN 1724:1998, prepared by CEN/TC 188.
ISO 21182:2005(E) iv
INTERNATIONAL STANDARD ISO 21182:2005(E) © ISO 2005 – All rights reserved
1Light conveyor b
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.