2023/1230 - Regulation (EU) 2023/1230 of the European Parliament and of the Council of 14 June 2023 on machinery and repealing Directive 2006/42/EC of the European Parliament and of the Council and Council Directive 73/361/EEC (Text with EEA relevance)

IEC 62841-3-15:2024 is to be used in conjunction with the first edition of IEC 62841-1 (2014).
This document supplements or modifies the corresponding clauses in IEC 62841-1:2014, so as to convert it into the IEC Standard: Particular requirements for transportable magnetic drills.
Where a particular subclause of IEC 62841-1:2014 is not mentioned in this Part 3-15, that subclause applies as far as relevant. Where this document states "addition", "modification" or "replacement", the relevant text in IEC 62841-1:2014 is to be adapted accordingly.
IEC 62841-1:2014, Clause 1 is applicable, except as follows.
Addition: This document applies to transportable magnetic drills which can include a liquid system.

2022-07-14: This prAA represents common mods to EN IEC 62841-3-15 (PR=75586)
D164/C043: DOW = DOR + 48 months

This document specifies the requirements for declaration and verification of vibration emission values of continuous and repeated shock vibrations. It is applicable to hand-arm and whole-body vibration values achieved by measurements according to type-B and type-C standards for portable hand-held, hand-guided and mobile machinery.
This document
—   gives guidance on the declaration of vibration emission values,
—   describes vibration and product information to be given in the instructions for use supplied with the machinery, and
—   specifies the method for verifying the declared vibration emission values stated in the instruction for use of the machinery.
NOTE   Machines according to Machinery Regulation (EU) 2023/1230 Annex III Part B 2.2.1.1 and 3.6.3.1 are covered by this document.

This part of IEC 60947-5 provides detailed specifications relating to the electrical and mechanical construction of emergency stop devices with mechanical latching function and to their testing.
This document is applicable to electrical control circuit devices and switching elements which are used to initiate an emergency stop signal. Such devices can be provided with their own enclosure and will be installed according to the product documentation.
This document does not apply to:
– emergency stop devices for non-electrical control applications, for example hydraulic or pneumatic;
– emergency stop devices without mechanical latching function.
An emergency stop device conforming to this document can also be used as part of an emergency switching off means in compliance with IEC 60364-5-53.
NOTE See also IEC 60204-1:2016 and IEC 60204-1:2016/AMD1:2021, 9.2.3.4.
This document does not address specific requirements on acoustic noise as the noise emission of electrical emergency stop devices with mechanical latching function is not considered to be a relevant hazard.

IEC 62841-3-15:2024 is to be used in conjunction with the first edition of IEC 62841-1 (2014). This document supplements or modifies the corresponding clauses in IEC 62841-1:2014, so as to convert it into the IEC Standard: Particular requirements for transportable magnetic drills. Where a particular subclause of IEC 62841-1:2014 is not mentioned in this Part 3-15, that subclause applies as far as relevant. Where this document states "addition", "modification" or "replacement", the relevant text in IEC 62841-1:2014 is to be adapted accordingly. IEC 62841-1:2014, Clause 1 is applicable, except as follows. Addition: This document applies to transportable magnetic drills which can include a liquid system.

2022-07-14: This prAA represents common mods to EN IEC 62841-3-15 (PR=75586)
D164/C043: DOW = DOR + 48 months

This document specifies requirements for the design and selection of electrical, mechanical, hydraulic and pneumatic equipment used in all types of cranes and their associated fixed load lifting attachments with the objectives of protecting personnel from hazards affecting their health and safety.
NOTE 1   Specific requirements for particular types of cranes, and for load lifting attachments, are given in the appropriate European Standard.
The electrical equipment covered by this document commences at the point of connection of the supply to the crane (the crane supply switch) including systems for power supply and control feeders situated outside the crane, e.g. flexible cables, conductor wires or bars, electric motors and cableless controls.
The principles to be applied for cranes transporting hazardous loads are given in this document. Particular requirements are given for cranes transporting hot molten metal.
This document does not cover the detail design of individual items of equipment except with regard to their selection for specific aspects of use.
The proof of competence calculations and related strength requirements or safety margins of equipment and components are not covered by this document.
NOTE 2   Some safety margins are given here for issues not covered in the EN 13001 series.
Hazards due to noise are not covered by this document. They are addressed in safety standards specific to each type of crane.
The specific hazards due to potentially explosive atmospheres, ionizing radiation, and operation in electromagnetic fields are not covered by this document.
The significant hazards covered by this document are identified in Annex A.
This document is not applicable to cranes manufactured before the date of its publication.

This document specifies the requirements for declaration and verification of vibration emission values of continuous and repeated shock vibrations. It is applicable to hand-arm and whole-body vibration values achieved by measurements according to type-B and type-C standards for portable hand-held, hand-guided and mobile machinery.
This document
—   gives guidance on the declaration of vibration emission values,
—   describes vibration and product information to be given in the instructions for use supplied with the machinery, and
—   specifies the method for verifying the declared vibration emission values stated in the instruction for use of the machinery.
NOTE   Machines according to Machinery Regulation (EU) 2023/1230 Annex III Part B 2.2.1.1 and 3.6.3.1 are covered by this document.

This document specifies design requirements for non-powered means of access installed on cranes.
Slidable, retractable means of access are excluded from the scope, except movable hoop guards.
This document covers means of access to control stations and all access required for maintenance, certain erection and dismantling operations.
For those cranes which are intended to be erected and dismantled frequently to change their places of work, e.g. tower cranes, specific requirements for the access needed during these operations are not covered by this document and can be given in the appropriate European Standards for specific crane types.
Lighting of means of access is not covered by this document and can be given in the appropriate European Standards for specific crane types.
Specification of the required rescue equipment, use of rescue equipment and the adaptation of crane access to the selected rescue equipment, are not covered by this document and can be given in the appropriate European Standards for specific crane types.
NOTE   Specific requirements for access on particular types of cranes are given in the appropriate European Standard for the particular crane type.
The requirements given in this document do not take into account the safety distances related to:
-   guarding against hazard from moving parts;
-   relative movement between crane and adjacent structure or the ground/floor;
-   hazardous surface temperature;
-   electrical equipment.
The significant hazards covered by this document are identified in Annex A.
This document is not applicable to cranes manufactured before the date of its publication.

IEC 60947-5-5:2026 This edition includes the following significant technical changes with respect to the previous edition: a) re-shaping the document with the clause numbers and names to be in line with other documents of the 60947 series; b) review of the test method to reasonably determine that the latch mechanism meets the requirements of the document; c) new Annex B for special requirements for illuminated push-button type emergency stop devices, including the reference to a function to distinguish between "active and inactive" by changing the colour of the push-button depending on the illumination. This part of IEC 60947-5 provides detailed specifications relating to the electrical and mechanical construction of emergency stop devices with mechanical latching function and to their testing. This document is applicable to electrical control circuit devices and switching elements which are used to initiate an emergency stop signal. Such devices can be provided with their own enclosure and will be installed according to the product documentation. This document does not apply to: – emergency stop devices for non-electrical control applications, for example hydraulic or pneumatic; – emergency stop devices without mechanical latching function. An emergency stop device conforming to this document can also be used as part of an emergency switching off means in compliance with IEC 60364-5-53. NOTE See also IEC 60204-1:2016 and IEC 60204-1:2016/AMD1:2021, 9.2.3.4. This document does not address specific requirements on acoustic noise as the noise emission of electrical emergency stop devices with mechanical latching function is not considered to be a relevant hazard. This second edition cancels and replaces the first edition published in 1997. This edition constitutes a technical revision.

This document supplements or modifies the corresponding clauses in IEC 62841-1, so as to convert it into the IEC Standard: Particular requirements for transportable planers and thicknessers.
IEC 62841-1:2014, Clause 1 is applicable, except as follows:
This document applies to transportable planers, thicknessers and combined planers and thicknessers intended for cutting wood and analogous materials with a maximum planing width of 330 mm.
This document does not apply to planers, thicknessers or combined planers and thicknessers other than transportable.
NOTE 101 ISO 19085-7:2019 gives requirements for planers, thicknessers or combined planers and thicknessers other than transportable.

2022-01-05:: This prAA includes common mods to EN IEC 62841-3-3 (PR=75427)
DOW=DOR+48 months is applied to all parts in EN IEC 62841 series

This document specifies technical safety requirements and measures to be adopted by persons undertaking the design, manufacture and supply of press brakes which are intended to work cold metal or material partly of cold metal but which can be used in the same way to work other sheet materials (e.g. cardboard, plastic, rubber, leather) and also referred to as machines.
NOTE 1        The design of a machine includes the study of the machine itself, taking into account all phases of the “life” of the machine mentioned in ISO 12100:2010, 5.4, and the drafting of the instructions related to all the above phases.
This document covers the following types of machines (see Annex J):
hydraulic press brakes;
hydraulic servo-drive press brakes;
screw servo-drive press brakes;
belt-spring servo-drive press brakes.
The requirements in this document take account of intended use, as defined in ISO 12100:2010, 3.23, as well as reasonably foreseeable misuse, as defined in ISO 12100:2010, 3.24. This document presumes access to the press brake from all directions, deals with all significant hazards during the various phases of the life of the machine described in Clause 4, and specifies the safety measures for both the operator and other exposed persons.
NOTE 2        All significant hazards means those identified or associated with press brakes at the time of the publication of this document.
This document can also be used as a guide for the design of press brakes which are intended to be integrated in a manufacturing system.
This document deals with all significant hazards, hazardous situations or hazardous events relevant to press brakes and ancillary devices (see Clause 4) when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer. This document specifies the safety requirements for press brakes defined in Clause 3.
This document does not cover press brakes which transmit energy to impart beam motion by using pneumatic means or mechanical clutch or press brakes that use combination of technologies (e.g. combined hydraulic and screw servo-drive press brake or combined hydraulic servo-drive and screw servo-drive press brake).
This document does not cover machines whose principal designed purpose is:
sheet folding by rotary action;
tube and pipe bending by rotary action;
roll bending.
This document does not cover hazards related to the use of press brakes in explosive atmospheres.
This document is not applicable to press brakes which are manufactured before the date of its publication.
This document does not cover the safety aspect of equipment for automatic workpiece loading and unloading where provided. Guidance on how to take into account additional automatic loading and unloading equipment can be found in ISO 11161:2007.

This document is applicable to protective ventilation systems to provide breathing air to operator's stations on earth-moving machinery used in contaminated areas. Its purpose is to limit the exposure of the operator (driver) to hazardous agents when earth-moving machinery is used in contaminated areas.
This document describes requirements, test procedures and information to be provided by the manufacturer of protective ventilation systems to provide breathing air to operator's stations on earthmoving machinery used in contaminated areas.
This document gives requirements additional to the common safety requirements of EN 474-1:2022 "Earthmoving machinery - Safety - Part 1: General requirements" and to the machine specific parts of the EN 474:2022 series.
This document does not repeat the requirements from the EN 474:2022 series but adds or replaces the requirements as applicable for Earth-moving machinery.
This document does not cover:
-   the safety requirements to be used for any specific application;
-   the choice of the system for a specific application site;
-   the filter performance or the relevant filtration class for any particular application;
-   the choice of type of filter for a specific application;
-   the cab performance requirement when in-use;
-   the filter durability when in-use.
This document is not applicable to protective ventilation systems which are manufactured before the date of its publication as an EN.
For the list of significant hazards, see informative Annex A.

IEC 62841-3-3:2024 is to be used in conjunction with IEC 62841-1:2014. This document supplements or modifies the corresponding clauses in IEC 62841-1, so as to convert it into the IEC Standard: Particular requirements for transportable planers and thicknessers. IEC 62841-1:2014, Clause 1 is applicable, except as follows: This document applies to transportable planers, thicknessers and combined planers and thicknessers intended for cutting wood and analogous materials with a maximum planing width of 330 mm. This document does not apply to planers, thicknessers or combined planers and thicknessers other than transportable. NOTE 101 ISO 19085-7:2019 gives requirements for planers, thicknessers or combined planers and thicknessers other than transportable.

2022-01-05:: This prAA includes common mods to EN IEC 62841-3-3 (PR=75427)
DOW=DOR+48 months is applied to all parts in EN IEC 62841 series

This document specifies safety requirements for spreaders used with cranes designed for the purpose of handling freight containers, e.g. those based on ISO 668:2020. The connection between the spreader and the container is by the use of twistlocks that engage into the container’s upper corner castings.
This document deals with all significant hazards, hazardous situations or hazardous events relevant to container handling spreaders, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.
The spreader is interfaced to the crane’s control and safety system.
This document does not cover the following types of spreaders:
-   hand operated spreaders (without external power supply);
-   bottom lift grapple spreaders used for swap bodies and road trailers.
This document does not deal with the lifting of persons.
This document is not applicable to container handling spreaders manufactured before the date of its publication.

2021-12-07: This prAA includes CMs to prEN IEC (PR=75392)
DOW=DOR+48 months

IEC 62841-3-11:2024 applies to transportable combined mitre and bench saws intended to be used with a toothed saw blade for cutting wood and analogous materials, plastics and nonferrous metals except magnesium with a saw blade diameter not exceeding 315 mm, which hereinafter is simply referred to as saw or tool.
This document does not apply to:
- saws intended to cut other metals, such as magnesium, steel and iron, or food;
- saws with an automatic feeding device;
- saws designed for use with abrasive wheels;
- saws designed for use with dado blades;
- single function bench or table saws;
- single function mitre saws;
- combined mitre and bench saws other than transportable.
NOTE 101 Transportable saws intended to cut ferrous metals will be covered by a future part of IEC 62841-3.
NOTE 102 Transportable tools designed for use with abrasive wheels are covered by IEC 62841-3-10:2015.
NOTE 103 Transportable table saws are covered by IEC 62841-3-1:2014.
NOTE 104 Transportable mitre saws are covered by IEC 62841-3-9:2020.
NOTE 105 In Europe (EN IEC 62841-3-11), the following additional NOTE applies:
NOTE Z101 Combined mitre and bench saws other than transportable are covered by EN 1870-3:2014.
This document is to be used in conjunction with IEC 62841-1:2014. This document supplements or modifies the corresponding clauses in IEC 62841-1, so as to convert it into the IEC Standard: Particular requirements for transportable combined mitre and bench saws.

This document is applicable to protective ventilation systems to provide breathing air to operator's stations on earth-moving machinery used in contaminated areas. Its purpose is to limit the exposure of the operator (driver) to hazardous agents when earth-moving machinery is used in contaminated areas.
This document describes requirements, test procedures and information to be provided by the manufacturer of protective ventilation systems to provide breathing air to operator's stations on earthmoving machinery used in contaminated areas.
This document gives requirements additional to the common safety requirements of EN 474-1:2022 "Earthmoving machinery - Safety - Part 1: General requirements" and to the machine specific parts of the EN 474:2022 series.
This document does not repeat the requirements from the EN 474:2022 series but adds or replaces the requirements as applicable for Earth-moving machinery.
This document does not cover:
-   the safety requirements to be used for any specific application;
-   the choice of the system for a specific application site;
-   the filter performance or the relevant filtration class for any particular application;
-   the choice of type of filter for a specific application;
-   the cab performance requirement when in-use;
-   the filter durability when in-use.
This document is not applicable to protective ventilation systems which are manufactured before the date of its publication as an EN.
For the list of significant hazards, see informative Annex A.

IEC 62841-3-16:2025 applies to transportable belt sanders, disc sanders and belt/disc sanders which are equipped with
– a sanding belt; or
– a sanding disc; or
– a sanding belt and a sanding disc
for sanding solid materials.
This document does not apply to hand-held disc-type sanders.
NOTE 101 Hand-held disc-type sanders are covered by IEC 62841-2-3.
This document does not apply to hand-held belt sanders.
NOTE 102 Hand-held belt sanders are covered by IEC 62841-2-4.
This Part 3-16 is to be used in conjunction with the first edition of IEC 62841-1:2014 and IEC 62841-1:2014/AMD1:2025.
This Part 3-16 supplements or modifies the corresponding clauses in IEC 62841-1:2014, so as to convert it into the IEC Standard: Particular requirements for transportable belt sanders, disc sanders and belt/disc sanders.
Where a particular subclause of IEC 62841-1:2014 is not mentioned in this Part 3-16, that subclause applies as far as relevant. Where this document states "addition", "modification" or "replacement", the relevant text in IEC 62841-1:2014 is to be adapted accordingly.
NOTE The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations can need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests.
It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication.

2021-12-07: This prAA includes CMs to prEN IEC (PR=75392)
DOW=DOR+48 months

IEC 62841-3-11:2024 applies to transportable combined mitre and bench saws intended to be used with a toothed saw blade for cutting wood and analogous materials, plastics and nonferrous metals except magnesium with a saw blade diameter not exceeding 315 mm, which hereinafter is simply referred to as saw or tool. This document does not apply to: - saws intended to cut other metals, such as magnesium, steel and iron, or food; - saws with an automatic feeding device; - saws designed for use with abrasive wheels; - saws designed for use with dado blades; - single function bench or table saws; - single function mitre saws; - combined mitre and bench saws other than transportable. NOTE 101 Transportable saws intended to cut ferrous metals will be covered by a future part of IEC 62841-3. NOTE 102 Transportable tools designed for use with abrasive wheels are covered by IEC 62841-3-10:2015. NOTE 103 Transportable table saws are covered by IEC 62841-3-1:2014. NOTE 104 Transportable mitre saws are covered by IEC 62841-3-9:2020. NOTE 105 In Europe (EN IEC 62841-3-11), the following additional NOTE applies: NOTE Z101 Combined mitre and bench saws other than transportable are covered by EN 1870-3:2014. This document is to be used in conjunction with IEC 62841-1:2014. This document supplements or modifies the corresponding clauses in IEC 62841-1, so as to convert it into the IEC Standard: Particular requirements for transportable combined mitre and bench saws.

This document is to be used together with the other generic parts of the EN 13001 series of standards, see Annex E, as well as pertinent crane type product EN standards, and as such they specify general conditions, requirements and methods to, by design and theoretical verification, prevent mechanical hazards of hydraulic cylinders that are part of the load carrying structures of cranes. Hydraulic piping, hoses and connectors used with the cylinders are not within the scope of this document, as well as cylinders made from other material than carbon steel.
NOTE 1   Specific requirements for particular crane types are given in the appropriate European product standards, see Annex E.
The significant hazardous situations and hazardous events that could result in risks to persons during intended use are identified in Annex F. Clauses 5 to 7 of this document provide requirements and methods to reduce or eliminate these risks:
a)   exceeding the limits of strength (yield, ultimate, fatigue);
b)   elastic instability (column buckling).
NOTE 2   EN 13001-3-6 deals only with the limit state method in accordance with EN 13001-1.

IEC 62841-3-16:2025 applies to transportable belt sanders, disc sanders and belt/disc sanders which are equipped with – a sanding belt; or – a sanding disc; or – a sanding belt and a sanding disc for sanding solid materials. This document does not apply to hand-held disc-type sanders. NOTE 101 Hand-held disc-type sanders are covered by IEC 62841-2-3. This document does not apply to hand-held belt sanders. NOTE 102 Hand-held belt sanders are covered by IEC 62841-2-4. This Part 3-16 is to be used in conjunction with the first edition of IEC 62841-1:2014 and IEC 62841-1:2014/AMD1:2025. This Part 3-16 supplements or modifies the corresponding clauses in IEC 62841-1:2014, so as to convert it into the IEC Standard: Particular requirements for transportable belt sanders, disc sanders and belt/disc sanders. Where a particular subclause of IEC 62841-1:2014 is not mentioned in this Part 3-16, that subclause applies as far as relevant. Where this document states "addition", "modification" or "replacement", the relevant text in IEC 62841-1:2014 is to be adapted accordingly. NOTE The attention of National Committees is drawn to the fact that equipment manufacturers and testing organizations can need a transitional period following publication of a new, amended or revised IEC publication in which to make products in accordance with the new requirements and to equip themselves for conducting new or revised tests. It is the recommendation of the committee that the content of this publication be adopted for implementation nationally not earlier than 36 months from the date of publication.

This document is to be used together with the other generic parts of the EN 13001 series of standards, see Annex E, as well as pertinent crane type product EN standards, and as such they specify general conditions, requirements and methods to, by design and theoretical verification, prevent mechanical hazards of hydraulic cylinders that are part of the load carrying structures of cranes. Hydraulic piping, hoses and connectors used with the cylinders are not within the scope of this document, as well as cylinders made from other material than carbon steel.
NOTE 1   Specific requirements for particular crane types are given in the appropriate European product standards, see Annex E.
The significant hazardous situations and hazardous events that could result in risks to persons during intended use are identified in Annex F. Clauses 5 to 7 of this document provide requirements and methods to reduce or eliminate these risks:
a)   exceeding the limits of strength (yield, ultimate, fatigue);
b)   elastic instability (column buckling).
NOTE 2   EN 13001-3-6 deals only with the limit state method in accordance with EN 13001-1.

This document applies to tyre curing machines having the following configuration:
-   crossing flow tyre curing machines, with one cavity with manual or automatic feeding and discharge;
-   crossing flow tyre curing machines, with two cavities, with manual or automatic feeding and discharge and with:
-   common curing cycle and common safeguarding; or
-   independent curing cycles and common safeguarding; or
-   independent curing cycles and independent safeguarding;
-   tyre curing machines with automatic rear feeding and discharge.
The safety requirements and/or protective measures specified in this document apply to tyre curing machines used to cure bicycle, motorcycle, passenger vehicle and truck tyres or other tyres that can be cured according to the requirements of this document.
This document deals with the following ancillary equipment that are an integral part in a tyre curing machine:
-   loading/unloading device;
-   take-away conveyor;
-   Post Cure Inflator (PCI) integrated in the rear side of a crossing flow machines for passenger vehicle tyres;
-   spraying jib.
This document does not deal with:
-   feeding system and discharge system;
-   tyre curing machines with manual loading of the green tyre into the mould and manual unloading of the cured tyre from the mould;
-   ancillary equipment which is not an integral part of the tyre curing machine, e.g. conveying equipment;
-   exhaust systems.
This document deals with all significant hazards, hazardous situations and events relevant to tyre curing machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex A).
It does not deal with hazards associated with falling of parts of the container or mould because they are not part of the machinery.
This document is not applicable to tyre curing machines which are manufactured before the date of its publication as an EN.

This document covers shank hooks made of steel forgings or steel castings, including stainless steel, with shanks machined for a thread/nut suspension of the hook.
Plate hooks, which are those, assembled of one or several parallel parts of rolled steel plates, are not covered by this document.
The significant hazardous situations and hazardous events that could result in risks to persons during intended use and reasonably foreseeable misuse are identified in Annex N. Clauses 4 to 6 of this document provide requirements and methods to reduce or eliminate the risks of exceeding the limits of strength (yield, ultimate, fatigue, brittle fracture) considering temperature limits of material.
The hazards covered by this document are identified in Annex N. This document is applicable to hooks installed in cranes manufactured after the date of approval of this European Standard by CEN and serves as a reference base for product standards of particular crane types.
This part of EN 13001 deals only with the limit state method in accordance with EN 13001-1:2015.

This document covers shank hooks made of steel forgings or steel castings, including stainless steel, with shanks machined for a thread/nut suspension of the hook.
Plate hooks, which are those, assembled of one or several parallel parts of rolled steel plates, are not covered by this document.
The significant hazardous situations and hazardous events that could result in risks to persons during intended use and reasonably foreseeable misuse are identified in Annex N. Clauses 4 to 6 of this document provide requirements and methods to reduce or eliminate the risks of exceeding the limits of strength (yield, ultimate, fatigue, brittle fracture) considering temperature limits of material.
The hazards covered by this document are identified in Annex N. This document is applicable to hooks installed in cranes manufactured after the date of approval of this European Standard by CEN and serves as a reference base for product standards of particular crane types.
This part of EN 13001 deals only with the limit state method in accordance with EN 13001-1:2015.

IEC 62841-2-16:2024 is to be used in conjunction with IEC 62841-1:2014. This document supplements or modifies the corresponding clauses in IEC 62841-1, so as to convert it into the IEC Standard: Particular requirements for hand-held fastener driving tools. Where a particular subclause of IEC 62841-1 is not mentioned in this document, that subclause applies as far as reasonable. Where this document states "addition", "modification" or "replacement", the relevant text in IEC 62841-1 is to be adapted accordingly. IEC 62841-1:2014, Clause 1 is applicable, except as follows: Addition: This document applies to hand-held fastener driving tools - intended for driving fasteners into or through concrete, fabric, fiberboard, metal, plastic, wood, wood products, cartons, and other materials; and - whose energy to drive the fastener is derived directly or indirectly from an electric motor or magnetic drive. This document does not apply to pneumatically driven tools where the compressed gas comes from an external source, such as a compressor or a tank. This document does not apply to tools powered by combustible gases, even if electrically ignited. NOTE 101 Tools powered by compressed air or combustible gases are covered by ISO 11148-13:2017.

This document applies to tyre curing machines having the following configuration:
-   crossing flow tyre curing machines, with one cavity with manual or automatic feeding and discharge;
-   crossing flow tyre curing machines, with two cavities, with manual or automatic feeding and discharge and with:
-   common curing cycle and common safeguarding; or
-   independent curing cycles and common safeguarding; or
-   independent curing cycles and independent safeguarding;
-   tyre curing machines with automatic rear feeding and discharge.
The safety requirements and/or protective measures specified in this document apply to tyre curing machines used to cure bicycle, motorcycle, passenger vehicle and truck tyres or other tyres that can be cured according to the requirements of this document.
This document deals with the following ancillary equipment that are an integral part in a tyre curing machine:
-   loading/unloading device;
-   take-away conveyor;
-   Post Cure Inflator (PCI) integrated in the rear side of a crossing flow machines for passenger vehicle tyres;
-   spraying jib.
This document does not deal with:
-   feeding system and discharge system;
-   tyre curing machines with manual loading of the green tyre into the mould and manual unloading of the cured tyre from the mould;
-   ancillary equipment which is not an integral part of the tyre curing machine, e.g. conveying equipment;
-   exhaust systems.
This document deals with all significant hazards, hazardous situations and events relevant to tyre curing machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex A).
It does not deal with hazards associated with falling of parts of the container or mould because they are not part of the machinery.
This document is not applicable to tyre curing machines which are manufactured before the date of its publication as an EN.

This document specifies the safety requirements for the design of must and grape harvest pumps and the means for verifying these requirements and gives information for the safe use of the machines covered.
This document applies to must and grape harvest pumps, as defined in 3.1, intended for the transfer of fresh, de-stemmed grapes and pomace.
This document deals with all significant hazards, hazardous situations or hazardous events relevant to grape harvest pumps, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, specified in Annex B.
This document does not deal with hazardous phenomena associated with the integration of grape harvest pumps with other machinery.
This document does not give additional requirements for operations subject to special rules (e.g. explosive atmosphere, power supply from electrical networks where the voltage, frequency and tolerance differ from those of the public network).
This document is not applicable to:
-   adaptations intended for other fruit harvests;
-   pumps for building materials (covered by EN 12001 [1]);
-   pumps on grape harvesters;
-   reception conquests;
-   machines upstream or downstream of the pump.
This document is not applicable to grape harvest pumps manufactured before the date of its publication.

This document specifies the safety requirements for the design of must and grape harvest pumps and the means for verifying these requirements and gives information for the safe use of the machines covered.
This document applies to must and grape harvest pumps, as defined in 3.1, intended for the transfer of fresh, de-stemmed grapes and pomace.
This document deals with all significant hazards, hazardous situations or hazardous events relevant to grape harvest pumps, when it is used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer, specified in Annex B.
This document does not deal with hazardous phenomena associated with the integration of grape harvest pumps with other machinery.
This document does not give additional requirements for operations subject to special rules (e.g. explosive atmosphere, power supply from electrical networks where the voltage, frequency and tolerance differ from those of the public network).
This document is not applicable to:
-   adaptations intended for other fruit harvests;
-   pumps for building materials (covered by EN 12001 [1]);
-   pumps on grape harvesters;
-   reception conquests;
-   machines upstream or downstream of the pump.
This document is not applicable to grape harvest pumps manufactured before the date of its publication.

This document covers safety requirements for powder actuated fixing and hard marking tools which operate with an intermediate member (piston) and are handled manually.
This document deals with all significant hazards (see Annex I), hazardous situations and events relevant to powder actuated fixing and hard marking tools, when they are used as intended and under conditions of misuse which are reasonably foreseeable (see Clause 4). It deals with the significant hazards in the different operating modes and intervention procedures as referred to in EN ISO 12100:2010, 5.4, 5.5, 5.6.
Although the safe use of powder actuated tools depends to an important extent on the use of appropriate cartridges and fasteners, this document is not formulating requirements for the cartridges and fasteners to be used with the tools (see Clause 6).
This document applies to tools designed for use with cartridges with casings made of metal or plastic and with solid propellant and containing a minor quantity of primer mix with a composition different from that of the main propellant.
This document applies to tools designed for use with single cartridges or with cartridges collated in disks or in strips.
The fixing tools in the scope are those intended for use with fasteners made from metal.
NOTE   Information about cartridges can be found either in EN 16264:2014 or the publication of the Permanent International Commission for the Proof of Small Arms (C.I.P.).
This document is not applicable to powder actuated fixing and hard marking tools which are manufactured before this document’s date of publication.

This European Standard is applicable for travelators, with or without a tunnel, for winter sport or leisure use.
These requirements are applicable to travelators for the transport of persons (either passengers or operators) wearing snow-sliding devices, or pedestrians wearing ski boots or heavy boots who may be holding their snow-sliding devices, for winter sports activities. For other uses, the persons (whether passengers or operators) shall wear suitable (enclosed and solid) footwear for travelators.
NOTE Snow-sliding devices include seated ski equipment for handicapped people.
This document has been prepared on the basis of the automatic operation of these installations with no staff permanently present at the actual installation.
It covers requirements relating to the prevention of accidents and the safety of operators.
This document covers all the significant hazards, hazardous situations and hazardous events specific to travelators for winter sport or leisure activities, when they are used in conformity to the application for which they are intended as well as for inappropriate applications that could be reasonably foreseen by the manufacturer (see Clause 4).
This document does not apply either to moving walkways as specified in EN 115 or to loading bands as specified in EN 1907.
This document does not apply to travelators manufactured prior to the date of its publication as an EN.

This European Standard is applicable for travelators, with or without a tunnel, for winter sport or leisure use.
These requirements are applicable to travelators for the transport of persons (either passengers or operators) wearing snow-sliding devices, or pedestrians wearing ski boots or heavy boots who may be holding their snow-sliding devices, for winter sports activities. For other uses, the persons (whether passengers or operators) shall wear suitable (enclosed and solid) footwear for travelators.
NOTE Snow-sliding devices include seated ski equipment for handicapped people.
This document has been prepared on the basis of the automatic operation of these installations with no staff permanently present at the actual installation.
It covers requirements relating to the prevention of accidents and the safety of operators.
This document covers all the significant hazards, hazardous situations and hazardous events specific to travelators for winter sport or leisure activities, when they are used in conformity to the application for which they are intended as well as for inappropriate applications that could be reasonably foreseen by the manufacturer (see Clause 4).
This document does not apply either to moving walkways as specified in EN 115 or to loading bands as specified in EN 1907.
This document does not apply to travelators manufactured prior to the date of its publication as an EN.

This European Standard deals with the safety of sealed (hermetic and semi-hermetic type) motor-compressors, their protection and control systems, if any, which are intended for use in equipment for household and similar purposes and which conform with the standards applicable to such equipment. It applies to motor-compressors tested separately, under the most severe conditions that may be expected to occur in normal use, their rated voltage being not more than 250 V for single-phase motor-compressors and 480 V for other motor-compressors

This European Standard deals with the safety of sealed (hermetic and semi-hermetic type) motor-compressors, their protection and control systems, if any, which are intended for use in equipment for household and similar purposes and which conform with the standards applicable to such equipment. It applies to motor-compressors tested separately, under the most severe conditions that may be expected to occur in normal use, their rated voltage being not more than 250 V for single-phase motor-compressors and 480 V for other motor-compressors

This document specifies safety requirements.
This document is applicable to paper making and paper finishing machines. It contains definitions and requirements which apply to all paper making and paper finishing machines listed in Annex A and is intended to be used in connection with the specific part applicable for the respective machine listed in Annex A. Specific parts can contain additional requirements or deviations from EN 1034-1 in which case the specific stipulations take precedence over the specification made in EN 1034-1. The standard deals with the hazards listed in Annex B.
This document deals with all significant hazards, hazardous situations or hazardous events relevant to paper making and paper finishing machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.
This document does not apply to machines used in paper converting. See EN 1010-1 to EN 1010-5.
This document applies to machines produced after the date of publication of this standard.

This document specifies safety requirements.
This document is applicable to paper making and paper finishing machines. It contains definitions and requirements which apply to all paper making and paper finishing machines listed in Annex A and is intended to be used in connection with the specific part applicable for the respective machine listed in Annex A. Specific parts can contain additional requirements or deviations from EN 1034-1 in which case the specific stipulations take precedence over the specification made in EN 1034-1. The standard deals with the hazards listed in Annex B.
This document deals with all significant hazards, hazardous situations or hazardous events relevant to paper making and paper finishing machines, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.
This document does not apply to machines used in paper converting. See EN 1010-1 to EN 1010-5.
This document applies to machines produced after the date of publication of this standard.

his European Standard deals with the safety of electrically operated commercial grillers and toasters not intended for household use. The rated voltage being not more than 250 V for single-phase appliances connected between one phase and neutral, and 480 V for other appliances. Rotary or continuous grillers and toasters and similar appliances intended for grilling by radiant heat such as rotisseries, salamanders, etc. are within the scope of this standard. Appliances within the scope of this standard are typically used in restaurants, canteens, hospitals and commercial enterprises such as bakeries, butcheries, etc.

This European Standard Deals with the safety of electrically operated commerical multi-purpose cooking pans not intended for household use. The rated voltage being not more than 250 V for single-phase appliances connected between one phase and neutral and 480 V for other appliances. Appliances within the scope of this standard are typically used in restaurants, canteens, hospitals, and commercial enterprises such as bakeries, butcheries, etc. The electrical part of appliances making use of other forms of energy is also within the scope of this standard.

This European Standard deals with the safety of electrically operated commercial hot cupboards not intended for household use. The rated voltage being not more than 250 V for single-phase appliances connected between one phase and neutral, and 480 V for other appliances. Hot cupboards with heated tops, heated display cases, heated crockery dispensers and heated shelves and tables are also within the scope of this standard. The appliances within the scope of this standard are typically used in restaurants, canteens, hospitals and similar commercial enterprises.

1.1   This document specifies the safety requirements for lifting tables which fulfil the following characteristics:
—   serving no more than 2 fixed landings but able to pass a fixed landing and,
—   having a vertical travel speed of no more than 0,15 m/s, unless the lifting table is safe by position and,
—   raising or lowering goods (with or without operator(s) and/or authorized person(s)) with a fixed, movable or mobile lifting table or,
—   raising or lowering operator(s) and/or authorized person(s) with or without goods, to positions where they can carry out work from a fixed lifting table that is guided throughout its vertical travel only.
1.2   This document specifies the appropriate technical measures for eliminating and reducing the risks arising from the significant hazards listed in Annex B.
1.3   This document does not apply to the following equipment:
—   lifting tables with a vertical travel speed exceeding 0,15 m/s, unless the lifting table is safe by position;
—   lifting tables, serving more than 2 fixed landings of a construction, for lifting goods, with a vertical travel speed not exceeding 0,15 m/s (EN 1570 2:2016);
—   lifting tables, serving more than 2 fixed landings of a construction, for lifting operators, with a vertical travel speed not exceeding 0,15 m/s;
—   lifting tables carrying operators and installed in full enclosures with a vertical travel speed not exceeding 0,15 m/s;
—   lifting tables used on ships;
—   lifting tables designed for artists and stage set features during artistic performances (EN 17206:2020);
—   power operated lifting platforms for persons with impaired mobility (EN 81 41:2010);
—   mobile lifting tables for airport ground support equipment (EN 1915 2:2001+A1:2009 and EN 12312 1:2013);
—   mobile elevating work platforms (EN 280 1:2022);
—   vehicle servicing lifts (EN 1493:2022);
—   mobile lifting tables used for firefighting (EN 1777:2010);
—   mobile lifting tables with a horizontal travelling speed of more than 1,6 m/s;
—   rail dependent storage and retrieval equipment (EN 528:2021);
—   scissor lift pallet trucks (EN ISO 3691 5:2015);
—   lifting tables suspended from a ceiling.
1.4   This document does not consider the requirements for:
—   operation in severe conditions (e.g. extreme climates, freezer applications, strong magnetic fields);
—   operation subject to special rules (e.g. potentially explosive atmospheres, mines);
—   handling of loads, the nature of which could lead to dangerous situations (e.g. molten metal, acids, radiating materials, particularly brittle loads, loose loads (gravel, tubes));
—   hazards occurring during construction, transportation, and disposal;
—   equipment installed on the load platform or the replacing or maintaining of it;
—   integration into broader systems or other machines, etc.;
—   cable-less controls, i.e. wireless;
—   lifting tables where the hydraulic pressure is derived directly from gas pressure;
—   lifting tables powered by internal combustion engines.
This document is not applicable to lifting tables manufactured before the date of its publication.

This document is applicable to the following non-woven abrasive products: non-woven flap discs with backing plate, non-woven
unitized discs with backing plate, non-woven general purpose discs with backing plate. These products are manufactured using
abrasive grains and are entirely made of non-woven web.
This document specifies requirements and/or measures for removal or reduction of hazards resulting from the design and application
of the non-woven abrasive products.
This document also contains procedures and tests for verification of compliance with the requirements as well as safety information
for use, which is to be made available to the user by the manufacturer.
Further, this document lists the hazards to be taken into consideration.

This standard deals with the safety of electrically operated commercial deep fat fryers and doughnut fryers including pressurized types with a pressure not exceeding 50 kPa and a pressure volume litres product not exceeding 200, their rated voltage being not more than 250 V for single-phase appliances connected between one phase and neutral and 480 V for other appliances