iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 1455-1:1999

(Main)

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 1: Requirements for pipes, fittings and the system

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 1: Requirements for pipes, fittings and the system

This standard specifies the requirements for pipes, fittings and the system of acrylonitrile-butadiene-styrene (ABS) and acrylonitrile-styrene-acrylester (ASA) solid-wall piping systems in the field of soil and waste discharge (low and high temperature) - inside buildings (marked with "B") - for both inside buildings and buried in ground within the building structure (marked with "BD").

Kunststoff-Rohrleitungssysteme zum Ableiten von Abwasser (niedriger und hoher Temperatur) innerhalb der Gebäudestruktur - Acrylnitril-Butadien-Styrol (ABS) - Teil 1: Anforderungen an Rohre, Formstücke und das Rohrleitungssystem

Diese Norm legt für Vollwand-Rohrleitungssysteme aus Acrylnitril-Butadien-Styrol (ABS) und Acrylnitril-Styrol-Acrylester (ASA) Anforderungen an Rohre, Formstücke und das Rohrleitungssystem für Abwasserleitungen fest, die in Schwerkraftenwässerungsanlagen - innerhalb von Gebäuden (Anwendungskennzeichen "B") sowie - innerhalb von Gebäuden und erdverlegt innerhalb der Gebäudestruktur (Anwendungskennzeichen "BD" zum Ableiten von Abwasser (niedriger und hoher Temperatur) eingesetzt werden.

Systèmes de canalisations en plastique pour l'évacuation des eaux-vannes et des eaux usées (à basse et à haute température) à l'intérieur de la structure des bâtiments - Acrylonitrile-butadiène-styrène (ABS) - Partie 1: Exigences pour tubes, raccords ainsi que pour le système

Cette norme spécifie, pour les systèmes de canalisations à paroi pleine en acrylonitrile-butadiène-styrène (ABS) et en acrylonitrile-styrène-acrylester (ASA), les exigences pour les tubes, les raccords et le système, destinés à être utilisés pour l'évacuation des eaux-vannes et des eaux usées (à basse et à haute température) à l'intérieur des bâtiments (marqués "B") et pour les systèmes d'évacuation utilisables aussi bien à l'intérieur des bâtiments qu'en enterré dans la structure du bâtiment (marqués "BD").

Cevni sistemi iz polimernih materialov za nizko- in visokotemperaturne odvodne sisteme v stavbah - Akrilonitril-butadien-stiren (ABS) - 1. del: Zahteve za cevi, fitinge in sistem

General Information

Status
Withdrawn
Publication Date
20-Jul-1999
Withdrawal Date
13-Dec-2022
ICS
23.040.01 - Pipeline components and pipelines in general
91.140.80 - Drainage systems
Technical Committee
CEN/TC 155 - Plastics piping systems and ducting systems
Drafting Committee
CEN/TC 155/WG 33 - Thermoplastics piping systems for soil & waste discharge and non-pressure drainage and sewerage
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
14-Dec-2022
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
89/106/EEC - Construction products
Ref Project
SIST EN 1455-1:2000 - Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 1: Requirements for pipes, fittings and the system

Relations

Replaced By
EN 1455-1:2022 - Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 1: Specifications for pipes, fittings and the system
Effective Date
18-Apr-2018

Buy Standard

EN 1455-1:2000EN 1455-1:2000
PreviousNext
Standard
EN 1455-1:2000
English language
35 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Cevni sistemi iz polimernih materialov za nizko- in visokotemperaturne odvodne sisteme v stavbah - Akrilonitril-butadien-stiren (ABS) - 1. del: Zahteve za cevi, fitinge in sistemKunststoff-Rohrleitungssysteme zum Ableiten von Abwasser (niedriger und hoher Temperatur) innerhalb der Gebäudestruktur - Acrylnitril-Butadien-Styrol (ABS) - Teil 1: Anforderungen an Rohre, Formstücke und das RohrleitungssystemSystemes de canalisations en plastique pour l'évacuation des eaux-vannes et des eaux usées (a basse et a haute température) a l'intérieur de la structure des bâtiments - Acrylonitrile-butadiene-styrene (ABS) - Partie 1: Exigences pour tubes, raccords ainsi que pour le systemePlastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 1: Requirements for pipes, fittings and the system91.140.80Drenažni sistemiDrainage systems23.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
CEN/TS 1455-2:2023(Main)
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 2: Assessment of conformity
SIST-TS CEN/TS 1455-2:2023

This document gives guidance for specifying requirements for the AoC of compounds/formulation, products, joints and assemblies in accordance with the applicable part of EN 1455 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE   A basic test matrix provides an overview of the testing scheme in Annex A.
In conjunction with EN 1455-1 (see European foreword), this document is applicable to solid wall piping systems made of acrylonitrile-butadiene-styrene (ABS) intended to be used for soil and waste discharge (low and high temperature):
-   inside buildings (application area code "B");
-   both inside buildings and buried in ground within the building structure (application area code "BD").

  • Technical specification
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 1566-2:2023(Main)
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 2: Assessment of conformity
SIST-TS CEN/TS 1566-2:2023

This document gives guidance for specifying requirements for the AoC of compounds/formulations, products, joints and assemblies in accordance with the applicable part of EN 1566 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE   A basic test matrix provides an overview of the testing scheme in Annex A.
In conjunction with EN 1566 1 (see European foreword), this document is applicable to solid-wall piping systems made of chlorinated poly(vinyl chloride) (PVC C) intended to be used for or soil and waste discharge systems (low and high temperature):
-   inside buildings (application area code "B");
-   for both inside buildings and buried in ground within the building structure (application area code "BD").

  • Technical specification
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1455-1:2022(Main)
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 1: Specifications for pipes, fittings and the system
SIST EN 1455-1:2023

This document specifies the requirements for solid wall pipes with smooth internal and external surfaces, extruded from the same formulation throughout the wall, fittings and the system of acrylonitrile-butadiene-styrene (ABS) and acrylonitrile-styrene-acrylester (ASA) piping systems intended for soil and waste discharge applications (low and high temperature):
- inside buildings (application area code “B”);
- for both inside buildings and buried in ground within the building structure (application area code “BD”).
NOTE 1 The intended use is reflected in the marking of products by “B” or “BD”.
NOTE 2 Application “B” covers uses above ground inside buildings, or outside buildings fixed onto the wall.
NOTE 3 Pipes and fittings of the pipe series S 25 are intended to be used for application area “B” only.
NOTE 4 For use buried in ground within the building structure are intended only those components (marked with “BD”) with nominal outside diameters equal to or greater than 75 mm.
NOTE 5 EN 476 [5] specifies the general requirements for components used in discharge pipes, drains and sewers for gravity systems. Pipes and fittings conforming to this document fully meet these requirements.
This document is also applicable to ABS and ASA pipes, fittings and the system intended for the following purposes:
- ventilating part of the pipework in association with discharge applications;
- rainwater pipework within the building structure.
It also specifies the test parameters for the test methods that are referred to.
This document covers a range of nominal sizes, a range of pipes and fittings series and gives recommendations concerning colours.
NOTE 6 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
NOTE 7 Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex A can be used with pipes and fittings conforming to this document, provided they conform to the requirements for joint dimensions given in Clause 7 and to the requirements of Table 21.

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1566-1:2022(Main)
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Chlorinated poly(vinyl chloride) (PVC-C) - Part 1: Specifications for pipes, fittings and the system
SIST EN 1566-1:2023

This document specifies the requirements for solid wall pipes with smooth internal and external surfaces, extruded from the same formulation throughout the wall, fittings and the system of chlorinated poly(vinyl chloride) (PVC-C) piping systems intended for soil and waste discharge (low and high temperature):
- inside buildings (application area code “B”);
- for both inside buildings and buried in ground within the building structure (application area code “BD”).
NOTE 1 The intended use is reflected in the marking of products by “B” or “BD”.
NOTE 2 Application “B” covers uses above ground inside buildings, or outside buildings fixed onto the wall.
NOTE 3 Pipes and fittings of the pipe series S 25 are intended to be used for application area “B” only.
NOTE 4 For use buried in ground within the building structure are intended only those components (marked with “BD”) with nominal outside diameters equal to or greater than 75 mm.
NOTE 5 EN 476 [5] specifies the general requirements for components used in discharge pipes, drains and sewers for gravity systems. Pipes and fittings conforming to this document fully meet these requirements.
This document is applicable to PVC-C pipes and fittings and the system intended for the following purposes:
- ventilating part of the pipework in association with discharge applications;
- rainwater pipework within the building structure.
It also specifies the test parameters for the test methods that are referred to.
This document covers a range of nominal sizes, a range of pipe series and gives recommendations concerning colours.
NOTE 6 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
NOTE 7 Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex A can be used with pipes and fittings conforming to this document, provided they conform to the requirements for joint dimensions given in Clause 7 and to the requirements of Table 21.

  • Standard
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1519-1:2019/AC:2021(Corrigendum)
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylene (PE) - Part 1: Requirements for pipes, fittings and the system
SIST EN 1519-1:2019/AC:2021

2021-02-24 - TC - Correcting some editorial aspects in Table 13

  • Corrigendum
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 1519-2:2020(Main)
Plastic piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylene (PE) - Part 2: Guidance for the assessment of conformity
SIST-TS CEN/TS 1519-2:2020

This document gives requirements and guidance for the assessment of conformity of materials, products, joints and assemblies in accordance with EN 1519 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of third-party certification procedures.
NOTE 1   It is recommended that the quality management system conforms to or is no less stringent than the relevant requirements to EN ISO 9001 [1].
NOTE 2   If certification is involved, it is recommended that the certification body is compliant with either EN ISO/IEC 17065 [2] or EN ISO/IEC 17021-series [4], as applicable.
NOTE 3   A basic test matrix providing an overview of the testing scheme is given in Annex A.
In conjunction with EN 1519-1 this document is applicable to piping systems made of polyethylene (PE) intended to be used:
-   for soil and waste discharge systems (low and high temperature) inside buildings (application area code "B") and
-   for soil and waste discharge systems (low and high temperature) for both inside buildings and buried in ground within the building structure (application area code "BD").
This is reflected in the marking of products by "B" or "BD".

  • Technical specification
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
CEN/TS 17176-7:2020(Main)
Plastics piping systems for water supply and for buried and above ground drainage, sewerage and irrigation under pressure - Oriented unplasticized poly(vinyl chloride) (PVC-O) - Part 7: Assessment of conformity
SIST-TS CEN/TS 17176-7:2020

This document gives requirements and guidance for the assessment of conformity of compounds/formulations, products, joints and assemblies in accordance with the applicable parts of EN 17176 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE 1   The quality management system is expected to conform to or is no less stringent than the relevant requirements to EN ISO 9001 [1].
NOTE 2   If third-party certification is involved, the certification body is expected be accredited to EN ISO/IEC 17065 [2] or EN ISO/IEC 17021 [3], as applicable.
NOTE 3   In order to help the reader, a basic test matrix is given in Annex A.
In conjunction with EN 17176 1, EN 17176 2, CEN/TS 17176 3 and EN 17176 5, this document is applicable to oriented unplasticized poly(vinyl chloride) (PVC-O) plastics piping systems for water supply and for buried and above-ground drainage, sewerage and irrigation under pressure.

  • Technical specification
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1519-1:2019(Main)
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polyethylene (PE) - Part 1: Requirements for pipes, fittings and the system
SIST EN 1519-1:2019

This document specifies the requirements for solid-wall polyethylene (PE) pipes with smooth internal and external surfaces extruded from the same compound/formulation throughout the wall, fittings and the system for:
-   soil and waste discharge applications (low and high temperature) inside buildings (application area code "B");
-   soil and waste discharge applications (low and high temperature) for both inside buildings and buried in the ground within the building structure (application area code "BD").
NOTE 1   The intended use is reflected in the marking of products by "B" or "BD".
NOTE 2   For use buried in the ground within the building structure are intended only those components marked with "BD", with a nominal ring stiffness of at least SN4 for dimensions equal to or greater than 75 mm.
This document is also applicable to PE pipes and fittings and the system intended for the following purposes:
-   ventilating part of the pipework in association with discharge applications;
-   rainwater pipework within the building structure.
It also specifies the test parameters for the test methods referred to in this standard.
This document covers a range of nominal sizes, a range of pipes and fittings series and gives recommendations concerning colours.
NOTE 3   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes, e.g. CEN/TR 13801 [1].
NOTE 4   Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex B can be used with pipes and fittings conforming to this European Standard, if applicable.
It applies to pipes and fittings, marked with “B”, which are intended to be used inside buildings and outside buildings fixed onto the wall.
It applies to pipes and fittings, marked with “BD”, which are intended to be used for both inside buildings and buried in the ground within the building structure.
This standard is applicable to PE pipes and fittings of the following types:
-   plain-ended;
-   with integral elastomeric ring seal socket;
-   for butt fusion joints;
-   for electrofusion joints;
-   for mechanical joints
where the fittings can be manufactured by injection-moulding or can be fabricated from pipes and/or mouldings.
NOTE 5   EN 476[2] specifies the general requirements for components used in discharge pipes, drains and sewers for gravity systems. Pipes and fittings conforming to this standard fully meet these requirements.
NOTE 6   For information about the chemical resistance of PE, guidance is given in ISO/TR 10358[3] and for rubber materials in ISO/TR 7620[4].

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1451-1:2017/AC:2018(Corrigendum)
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system
SIST EN 1451-1:2018/AC:2018

TC - Modification to table 2 last column fifth line, in the three language versions.

  • Corrigendum
    2 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1451-1:2017(Main)
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) - Part 1: Specifications for pipes, fittings and the system
SIST EN 1451-1:2018

This part of EN 1451 specifies the requirements for solid-wall polypropylene (PP) pipes, fittings and the system intended for:
-   soil and waste discharge applications (low and high temperature) inside buildings (application area code "B");
-   soil and waste discharge applications (low and high temperature) for both inside buildings and buried in the ground within the building structure (application area code "BD").
This part of EN 1451 is also applicable to PP pipes and fittings and the system intended for the following purposes:
-   ventilating part of the pipework in association with discharge applications;
-   rainwater pipework within the building structure.
It also specifies the test parameters for the test methods referred to in this standard.
This standard covers a range of nominal sizes, a range of pipes and fittings series and gives recommendations concerning colours.
It applies to pipes and fittings, marked with "B", which are intended to be used inside buildings and outside buildings fixed onto the wall.
This standard is applicable to PP pipes and fittings of the following types:
-   plain-ended;
-   with integral elastomeric ring seal socket;
-   for butt fusion joints.
whereby the fittings can be manufactured by injection-moulding or be fabricated from pipes and/or mouldings.

  • Standard
    51 pages
    English language
    sale 10% off
    e-Library read for
    1 day