prEN ISO 5832-2
(Main)Implants for surgery - Metallic materials - Part 2: Unalloyed titanium (ISO/DIS 5832-2:2025)
Implants for surgery - Metallic materials - Part 2: Unalloyed titanium (ISO/DIS 5832-2:2025)
This document specifies the characteristics of, and corresponding test methods for, unalloyed titanium for use in the manufacture of surgical implants.
Six grades of titanium based on tensile strength are listed in Table 2.
NOTE The mechanical properties of a sample obtained from a finished product made of this metal do not necessarily comply with those specified in this document.
Chirurgische Implantate - Metallische Werkstoffe - Teil 2: Unlegiertes Titan (ISO/DIS 5832‑2:2025)
Implants chirurgicaux - Matériaux métalliques - Partie 2: Titane non allié (ISO/DIS 5832-2:2025)
L'ISO 5832-2:2018 spécifie les caractéristiques du titane non allié utilisé pour la fabrication des implants chirurgicaux et les méthodes d'essai correspondantes.
Le Tableau 2 répertorie six nuances de titane fondées sur la résistance à la traction.
NOTE Les caractéristiques mécaniques d'un échantillon prélevé sur un produit fini fabriqué avec ce métal ne sont pas nécessairement conformes aux valeurs spécifiées dans l'ISO 5832-2:2018.
Vsadki (implantati) za kirurgijo - Kovinski materiali - 2. del: Nelegirani titan (ISO/DIS 5832-2:2025)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-april-2025
Vsadki (implantati) za kirurgijo - Kovinski materiali - 2. del: Nelegirani titan
(ISO/DIS 5832-2:2025)
Implants for surgery - Metallic materials - Part 2: Unalloyed titanium (ISO/DIS 5832-
2:2025)
Chirurgische Implantate - Metallische Werkstoffe - Teil 2: Unlegiertes Titan (ISO/DIS
5832-2:2025)
Implants chirurgicaux - Matériaux métalliques - Partie 2: Titane non allié (ISO/DIS 5832-
2:2025)
Ta slovenski standard je istoveten z: prEN ISO 5832-2
ICS:
11.040.40 Implantanti za kirurgijo, Implants for surgery,
protetiko in ortetiko prosthetics and orthotics
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
International
Standard
ISO/DIS 5832-2
ISO/TC 150/SC 1
Implants for surgery — Metallic
Secretariat: DIN
materials —
Voting begins on:
Part 2: 2025-02-10
Unalloyed titanium
Voting terminates on:
2025-05-05
Implants chirurgicaux — Produits à base de métaux —
Partie 2: Titane non allié
ICS: 11.040.40
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Reference number
ISO/DIS 5832-2:2025(en)
DRAFT
ISO/DIS 5832-2:2025(en)
International
Standard
ISO/DIS 5832-2
ISO/TC 150/SC 1
Implants for surgery — Metallic
Secretariat: DIN
materials —
Voting begins on:
Part 2:
Unalloyed titanium
Voting terminates on:
Implants chirurgicaux — Produits à base de métaux —
Partie 2: Titane non allié
ICS: 11.040.40
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
© ISO 2025
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
BE CONSIDERED IN THE LIGHT OF THEIR
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
or ISO’s member body in the country of the requester.
NATIONAL REGULATIONS.
ISO copyright office
RECIPIENTS OF THIS DRAFT ARE INVITED
CP 401 • Ch. de Blandonnet 8
TO SUBMIT, WITH THEIR COMMENTS,
CH-1214 Vernier, Geneva
NOTIFICATION OF ANY RELEVANT PATENT
Phone: +41 22 749 01 11
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/DIS 5832-2:2025(en)
ii
ISO/DIS 5832-2:2025(en)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Chemical composition . 1
5 Microstructure. 2
5.1 Tensile properties .2
5.2 Bending properties .2
6 Test methods . 3
iii
ISO/DIS 5832-2:2025(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of stand
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.