Copper and copper alloys - Hot-dip tinned strip

This European Standard specifies:
-   the composition and tolerances on dimensions of strip produced by rolling in the thickness range from 0,10 mm up to and including 1,50 mm of copper and copper alloys to be tinned, with tin, a tin-lead alloy or other tin alloys;
-   the composition of material normally used for the melt;
-   the properties of strip before tinning;
-   the properties of hot-dip tinned strip;
-   the preferred thicknesses (mean values) and thickness ranges of coatings;
-   the edgewise curvature of hot-dip tinned strip;
-   the sampling procedure;
-   the methods of test to be used for verification of conformity to the requirements of this European
Standard;
   the delivery conditions.

Kupfer und Kupferlegierungen - Feuerverzinnte Bänder

Diese Europäische Norm legt fest:
-   die Zusammensetzung und Grenzabmaße von mit Zinn, einer Zinn Blei Legierung oder einer anderen Zinnlegierung zu verzinnenden Bänder, die durch walzen produziert wurden, mit einer Dicke von 0,10 mm bis 1,50 mm aus Kupfer und Kupferlegierungen;
-   die Zusammensetzung der für die Schmelze üblicherweise zu verwendenden Werkstoffe;
-   die Eigenschaften von Bändern vor dem Verzinnen;
-   die Eigenschaften von feuerverzinnten Bändern;
-   die bevorzugten Dicken (Mittelwerte) und Dickenbereiche von Überzügen;
-   die Säbelförmigkeit von feuerverzinnten Bändern;
-   den Ablauf der Probenentnahme;
-   die Prüfverfahren zur Feststellung der Übereinstimmung mit den Anforderungen dieser Europäischen Norm;
-   die Lieferbedingungen.

Cuivres et alliages de cuivre - Bandes étamées à chaud

La présente Norme européenne prescrit :
⎯ la composition et les tolérances des dimensions de la bande, dans une plage d’épaisseur de 0,10 mm
jusqu’à et y compris 1,50 mm, de cuivre et d'alliages de cuivre à étamer avec de l'étain, un alliage
étain-plomb ou d'autres alliages d'étain ;
⎯ la composition du matériau normalement utilisé pour la fusion ;
⎯ les propriétés de la bande avant étamage ;
⎯ les propriétés de la bande étamée à chaud ;
⎯ les épaisseurs recommandées (valeurs moyennes) et les plages d'épaisseurs pour les revêtements ;
⎯ la flèche latérale de la bande étamée à chaud ;
⎯ le mode opératoire d'échantillonnage ;
⎯ les méthodes d'essai à utiliser pour la vérification de la conformité aux exigences de la présente Norme
européenne ;
⎯ les conditions de livraison.

Baker in bakrove zlitine - Vroče pokositreni trakovi

Ta evropski standard določa:
 sestavo in tolerance dimenzij trakov, proizvedenih z valjanjem v razponu debeline od 0,10 mm do vključno 1,50 mm bakra in bakrovih zlitin, ki se bodo pokositrile s kositrom, kositrovo-svinčeno zlitino ali drugimi kositrovimi zlitinami;
 sestavo materiala, ki se po navadi uporablja za taljenje;
 lastnosti trakov pred kositrenjem;
 lastnosti vroče pokositrenih trakov;
 prednostne debeline (povprečne vrednosti) in razpon debelin prevlek;
 robno ukrivljenost vroče pokositrenih trakov;
 postopek vzorčenja;
 metode preskušanja, ki se uporabljajo za preverjanje skladnosti z zahtevami tega evropskega
standarda;
 dobavne pogoje.

General Information

Status
Published
Publication Date
28-Sep-2010
Withdrawal Date
30-Mar-2011
Current Stage
9093 - Decision to confirm - Review Enquiry
Completion Date
19-Nov-2020

Relations

Buy Standard

Standard
EN 13148:2011
English language
43 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Kupfer und Kupferlegierungen - Feuerverzinnte BänderCuivres et alliages de cuivre - Bandes étamées à chaudCopper and copper alloys - Hot-dip tinned strip77.150.30Bakreni izdelkiCopper productsICS:Ta slovenski standard je istoveten z:EN 13148:2010SIST EN 13148:2011en,fr,de01-maj-2011SIST EN 13148:2011SLOVENSKI
STANDARDSIST EN 13148:20041DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13148
September 2010 ICS 77.150.30 Supersedes EN 13148:2001English Version
Copper and copper alloys - Hot-dip tinned strip
Cuivres et alliages de cuivre - Bandes étamées à chaud
Kupfer und Kupferlegierungen - Feuerverzinnte Bänder This European Standard was approved by CEN on 21 August 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13148:2010: ESIST EN 13148:2011

Testing of solderability of hot-dip tinned strip by means of vertical dipping test . 38Annex B (normative)
Measuring of coating thickness with X-ray spectrometric method according to EN ISO 3497 . 41Bibliography . 43SIST EN 13148:2011

Standard;  the delivery conditions. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1655, Copper and copper alloys — Declarations of conformity EN 1976, Copper and copper alloys — Cast unwrought copper products SIST EN 13148:2011

EN 13148:20
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.