CEN/TC 133/WG 2 - Rolled flat products

This European Standard specifies the composition, property requirements including electrical properties, and tolerances on dimensions and form for copper plate, sheet and strip for electrical purposes with thicknesses from 0,05 mm up to and including 25 mm and widths from 10 mm up to and including 1 250 mm.
The sampling procedures and the methods of test for verification of conformity to the requirements of this European Standard are also specified.

This European Standard specifies requirements for copper sheet and strip in thicknesses from 0,4 mm up to and including 1 mm and in widths up to and including 1 250 mm.
This European Standard is applicable to sheet and strip for use in building construction, e.g. for roof drainage systems, gutters, down pipes, roof coverings, external wall claddings, dormer windows, verges, chimney flashings and roof valleys.

This European Standard specifies:
-   the composition and tolerances on dimensions of strip produced by rolling in the thickness range from 0,10 mm up to and including 1,50 mm of copper and copper alloys to be tinned, with tin, a tin-lead alloy or other tin alloys;
-   the composition of material normally used for the melt;
-   the properties of strip before tinning;
-   the properties of hot-dip tinned strip;
-   the preferred thicknesses (mean values) and thickness ranges of coatings;
-   the edgewise curvature of hot-dip tinned strip;
-   the sampling procedure;
-   the methods of test to be used for verification of conformity to the requirements of this European
Standard;
   the delivery conditions.

This document specifies:
-   the composition and tolerances on dimensions in the thickness range from 0,1 mm up to and including 4 mm of strip of copper and copper alloys to be tinned with tin or a tin lead alloy or other tin alloys;
-   the composition of the material to be used for the coating;
-   the properties of strip before tinning;
-   the properties of the electrolytically tinned strip;
-   the preferred thicknesses (mean values) and thickness ranges of coatings and their eventual sub layers;
-   the types of coating and sub layer;
-   the edgewise curvature of electrolytically tinned strip;
-   the sampling procedure;
-   the methods of test to be used for verification of conformity to the requirements of this standard;
-   the delivery conditions.

TC - Table 2 - Change in Ni-content of CuNi2Be

This European Standard specifies a method for the determination of residual stresses in the areas adjacent to the slit edges of wrought copper and copper alloy strip, by measurement of the angle of twist, longitudinal curvature and sideways curvature of test pieces cut from strip.

Migrated from Progress Sheet (TC Comment) (2000-07-10): UAP of 4 months (TC Res 4/1998) (CC/981029)
2020-01-20: Originator of XML version: NEN (on behalf of NEN, ASI, DS, SFS, SIS, SN)

This European standard specifies test methods to determine the modulus of elasticity E and the spring bending limit O fb of strip in thicknesses from 0,05 mm up to and including 1,0 mm. This standard applies to strip specified in EN 1654.

This European Standard specifies the composition, property requirements and tolerances on dimensions and form for copper and copper alloy plate, sheet and circles for boilers, pressure vessels, heat exchangers and hot water storage units.  The sampling procedures, the methods of test for verification of conformity to the requirements of this standard, and the delivery conditions are also specified.

This European Standard specifies the composition, property requirements and tolerances on dimensions and form for copper and copper alloy strip for lead frame material, with width up to and including 100 mm. Thickness from 0,1 mm up to and including 1,0 mm, generally used for stamped lead frames for integrated circuits and low power devices and thicknesses from 1,0 mm up to and including 2,0 mm are generally used for stamped lead frames for high power devices.

This European Standard specifies the composition, property requirements and tolerances on dimensions and form for copper alloy strip intended for the fabrication of springs and connectors, with thicknesses from 0,1 mm up to and including 1,0 mm and with width up to and including 350 mm. The sampling procedures, the methods of test for verification of conformity to the requirements of this standard, and the delivery conditions are also specified.

This European Standard specifies the composition, property requirements and tolerances on dimensions and form for copper and copper alloy plate, sheet, strip and circles for general purposes.  The sampling procedures, the methods of test for verification of conformity to the requirements of this standard, and the delivery conditions are also specified.

This European Standard specifies the composition, property requirements including electrical properties, and
tolerances on dimensions and form for copper plate, sheet and strip for electrical purposes with thicknesses from
0,05 mm up to and including 25 mm and widths from 10 mm up to and including 1 250 mm.
The sampling procedures, the methods of test for verification of conformity to the requirements of this standard, and
the delivery conditions are also specified.

This European Standard specifies requirements for copper sheet and strip in thicknesses from 0,5 mm up to and including 1 mm and in widths up to and including 1250 mm. This standard is applicable to sheet and strip for use in building construction, e.g. for roof drainage systems, gutters, downpipes, roof coverings, external wall claddings, dormer windows, verges, chimney flashings and roof valleys.

This European Standard specifies:
-     the composition and tolerances on dimensions of strip in the thickness range from 0,10 mm up to and including
     1,50 mm of copper and copper alloys to be tinned, with tin, a tin-lead alloy or other tin alloys;
-    the composition of material normally used for the melt;
-    the properties of strip before tinning;
-    the properties of hot-dip tinned strip;
-    the preferred thicknesses (mean values) and thickness ranges of coatings;
-    the edgewise curvature of hot-dip tinned strip;
-    the sampling procedure;
-    the methods of test to be used for verification of conformity to the requirements of this standard;
-     the delivery conditions.