FprEN ISO 19069-2
(Main)Plastics - Polypropylene (PP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO/FDIS 19069-2:2024)
Plastics - Polypropylene (PP) moulding and extrusion materials - Part 2: Preparation of test specimens and determination of properties (ISO/FDIS 19069-2:2024)
ISO 19069-2:2016 specifies the methods of preparation of test specimens and the test methods to be used in determining the properties of polypropylene (PP) moulding and extrusion materials. Requirements for handling test material and for conditioning both the test material before moulding and the specimens before testing are given.
Procedures and conditions for the preparation of test specimens and procedures for measuring properties of the materials from which these specimens are made are also given. Properties and test methods which are suitable and necessary to characterize PP moulding and extrusion materials are listed.
The properties have been selected from the general test methods in ISO 10350‑1. Other test methods in wide use for, or of particular significance to, these moulding and extrusion materials are also included in this part of ISO 19069, as are the designatory properties specified in ISO 19069‑1.
In order to obtain reproducible and comparable test results, it is necessary to use the methods of preparation and conditioning, the specimen dimensions and the test procedures specified herein. Values determined will not necessarily be identical to those obtained using specimens of different dimensions or prepared using different procedures.
Kunststoffe - Polypropylen (PP)-Formmassen - Teil 2: Herstellung von Probekörpern und Bestimmung von Eigenschaften (ISO/FDIS 19069-2:2024)
Dieses Dokument legt die Verfahren zur Herstellung von Probekörpern und die Prüfverfahren zur Bestimmung der Eigenschaften von Polypropylen (PP)-Formmassen fest. Es enthält Anforderungen an die Handhabung des Prüfmaterials und an die Konditionierung sowohl des Prüfmaterials vor dem Formen als auch der Probekörper vor der Prüfung.
Dieses Dokument legt Verfahren und Bedingungen für die Herstellung von Probekörpern sowie die Verfahren zum Messen der Eigenschaften der Werkstoffe fest, aus denen diese Probekörper hergestellt werden. Eigenschaften und Prüfverfahren, die anwendbar und wichtig sind, um Polypropylen (PP)-Formmassen zu charakterisieren, sind aufgeführt.
Die Eigenschaften stammen aus den allgemeinen Prüfverfahren, wie sie in ISO 10350 1 festgelegt sind. Andere weithin gebräuchliche Prüfverfahren oder solche von besonderer Bedeutung für diese Formmassen, wie die kennzeichnenden Eigenschaften nach ISO 19069 1, sind in dieses Dokument aufgenommen.
Plastiques - Matériaux à base de polypropylène (PP) pour moulage et extrusion - Partie 2: Préparation des éprouvettes et détermination des propriétés (ISO/FDIS 19069-2:2024)
ISO 19069-2:2016 spécifie les méthodes de préparation des éprouvettes et les méthodes d'essai à appliquer pour déterminer les propriétés des polypropylènes (PP) pour moulage et extrusion. Elle indique les exigences requises lors de la manipulation du matériau pour essai, ainsi que lors de conditionnement dudit matériau avant moulage et des éprouvettes avant l'essai.
Elle précise les modes opératoires et les conditions nécessaires à la préparation des éprouvettes, ainsi que les modes opératoires de mesurage des propriétés des matériaux à partir desquels ces éprouvettes sont fabriquées. Elle fournit également une liste des propriétés et des méthodes d'essai appropriées et nécessaires à la caractérisation des polypropylènes pour moulage et extrusion.
Les propriétés ont été choisies parmi les méthodes d'essai générales données dans l'ISO 10350‑1. D'autres méthodes d'essai, présentant une importance particulière ou largement utilisées dans le cas de ces matériaux pour moulage et extrusion, sont également incluses dans la présente partie de l'ISO 19069, comme le sont les propriétés de désignation figurant dans l'ISO 19069‑1.
Pour obtenir des résultats d'essai reproductibles et comparables, il est nécessaire d'utiliser les méthodes de préparation et de conditionnement, ainsi que les dimensions d'éprouvettes et les modes opératoires d'essai prescrits ci-après. Les valeurs ainsi déterminées ne seront pas nécessairement identiques à celles obtenues en utilisant des éprouvettes de dimensions différentes ou préparées selon des modes opératoires différents.
Polimerni materiali - Polipropilenski (PP) materiali za oblikovanje in ekstrudiranje - 2. del: Priprava preskušancev in ugotavljanje lastnosti (ISO/FDIS 19069-2:2024)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN ISO 19069-2:2023
01-marec-2023
Nadomešča:
SIST EN ISO 19069-2:2016
Polimerni materiali - Polipropilenski (PP) materiali za oblikovanje in ekstrudiranje -
2. del: Priprava preskušancev in ugotavljanje lastnosti (ISO/DIS 19069-2:2023)
Plastics - Polypropylene (PP) moulding and extrusion materials - Part2: Preparation of
test specimens and determination of properties (ISO/DIS 19069-2:2023)
Kunststoffe - Polypropylen (PP)-Formmassen - Teil2: Herstellung von Probekörpern und
Bestimmung von Eigenschaften (ISO/DIS 19069-2:2023)
Plastiques - Matériaux à base de polypropylène (PP) pour moulage et extrusion - Partie
2: Préparation des éprouvettes et détermination des propriétés (ISO/DIS 19069-2:2023)
Ta slovenski standard je istoveten z: prEN ISO 19069-2
ICS:
83.080.20 Plastomeri Thermoplastic materials
oSIST prEN ISO 19069-2:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
oSIST prEN ISO 19069-2:2023
oSIST prEN ISO 19069-2:2023
DRAFT INTERNATIONAL STANDARD
ISO/DIS 19069-2
ISO/TC 61/SC 9 Secretariat: KATS
Voting begins on: Voting terminates on:
2023-01-02 2023-03-27
Plastics — Polypropylene (PP) moulding and extrusion
materials —
Part 2:
Preparation of test specimens and determination of
properties
Plastiques — Matériaux polypropylène (PP) pour moulage et extrusion —
Partie 2: Préparation des éprouvettes et détermination des propriétés
ICS: 83.080.20
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 19069-2:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023
oSIST prEN ISO 19069-2:2023
ISO/DIS 19069-2:2023(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 19069-2
ISO/TC 61/SC 9 Secretariat: KATS
Voting begins on: Voting terminates on:
Plastics — Polypropylene (PP) moulding and extrusion
materials —
Part 2:
Preparation of test specimens and determination of
properties
Plastiques — Matériaux polypropylène (PP) pour moulage et extrusion —
Partie 2: Préparation des éprouvettes et détermination des propriétés
ICS: 83.080.20
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2023
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: +41 22 749 01 11
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: copyright@iso.org
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 19069-2:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2022
oSIST prEN ISO 19069-2:2023
ISO/DIS 19069-2:2022(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 3
4 Preparation of test specimens . 3
4.1 General . 3
4.2 Treatment of the material before moulding . 3
4.3 Injection moulding . 3
4.4 Compression moulding. 4
5 Conditioning of test specimens . 4
6 Determination of properties .5
Bibliography . 9
iii
oSIST prEN ISO 19069-2:2023
ISO/DIS 19069-2:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT),see
www.iso.org/iso/foreword.html.
This document was prepared by Technical CommitteeISO/TC 61, Plastics, Subcommittee SC 9,
Thermoplastic materials.
This second edition cancels and replaces the first edition (ISO 19069-2:2016), which has been technically
revised.
The main changes compared to the previous edition are as follows:
— updated the Normative references;
— changed the NOTEs in Table 1of previous edition into text;
— added new the test condition of melt mass-flow rate and meltvolume-flowrate into Table 3;
— added two items of flexural strength and thermal oxidative stability in air into Table 3 and Table 4,
respectively.
A list of all parts in the ISO 19069 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
oSIST prEN ISO 19069-2:2023
DRAFT INTERNATIONAL STANDARD ISO/DIS 19069-2:2022(E)
Plastics — Polypropylene (PP) moulding and extrusion
materials —
Part 2:
Preparation of test specimens and determination of
properties
1 Scope
This document specifies the methods of preparation of test specimens and the test methods for
determining the properties of polypropylene (PP) moulding and extrusion materials. It gives
requirement for handling test material and for conditioning both the test material before moulding and
the specimens before testing.
This document describes procedures and conditions for the preparation of test specimens, and
procedures for measuring properties of the materials from which these specimens are made. Properties
and test methods which are suitable and essential to characterize PP moulding and extrusion materials
are listed.
The properties have been selected from the general test methods in ISO 10350-1. Other test methods in
wide use for, or of particular significance to PP moulding and extrusion materials are also included in
this document, as are the designatory properties specified in ISO 19069-1.
In order to obtain reproducible and comparable test results, it is desirable to use the methods of
specimen preparation and conditioning, the specimen dimensions and the test procedures specified
herein. Values determined will not necessarily be identical to those obtained using specimens of
different dimensions or prepared using different procedures.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 62, Plastics — Determination of water absorption
ISO 75-2, Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
ISO 178, Plastics — Determination of flexural properties
ISO 179-1, Plastics —Determination of Charpy impact properties —Part 1:Non-instrumented impact test
ISO 179-2, Plastics — Determination of Charpy impact properties — Part 2: Instrumented impact test
ISO 293, Plastics —Compression moulding of test specimens of thermoplastic materials
ISO 294-1, Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General
principles, and moulding of multipurpose and bar test specimens
ISO 294-3, Plastics — Injection moulding of test specimens of thermoplastic materials — Part 3: Small
plates
ISO 294-4, Plastics — Injection moulding of test specimens of thermoplastic materials — Part 4:
Determination of moulding shrinkage
oSIST prEN ISO 19069-2:2023
ISO/DIS 19069-2:2022(E)
ISO 527-2, Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and
extrusion plastics
ISO 899-1, Plastics — Determination of creep behaviour — Part 1: Tensile creep
ISO 1133-1, Plastics — Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR)
of thermoplastics — Part 1: Standard method
ISO 1183-1, Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion
method, liquid pycnometer method and titration method
ISO 1183-2, Plastics — Methods for determining the density of non-cellular plastics — Part 2: Density
gradient column method
ISO 1183-3, Plastics — Methods for determining the density of non-cellular plastics — Part 3: Gas
pyknometer method
ISO 1628-3, Plastics — Determination of the viscosity of polymers in dilute solution using capillary
viscometers — Part 3: Polyethylenes and polypropylenes
ISO 2818, Plastics — Preparation of test specimens by machining
ISO 4577, Plastics — Polypropylene and propylene-copolymers — Determination of thermal oxidative
stability in air — Oven method
ISO 4589-2, Plastics — Determination of burning behaviour by oxygen index — Part 2: Ambient-
temperature test
ISO 6603-2, Plastics — Determination of puncture impact behaviour of rigid plastics — Part 2: Instrumented
impact testing
ISO 8256, Plastics — Determination of tensile-impact strength
ISO 10350-1, Plastics — Acquisition and presentation of comparable single-point data — Part 1: Moulding
materials
ISO 11357-2, Plastics — Differential scanning calorimetry (DSC) — Part 2: Determination of glass transition
temperature and step height
ISO 11357-3, Plastics — Differential scanning calorimetry (DSC) — Part 3: Determination of temperature
and enthalpy of melting and crystallization
ISO 11359-2, Plastics — Thermomechanical analysis (TMA) — Part 2: Determination of coefficient of linear
thermal expansion and glass transition temperature
ISO 16152, Plastics — Determination of xylene-soluble matter in polypropylene
ISO 20753, Plastics — Test specimens
IEC 60112, Method for the determina
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.