EN ISO 13385-1:2011
(Main)Geometrical product specifications (GPS) - Dimensional measuring equipment - Part 1: Callipers; Design and metrological characteristics (ISO 13385-1:2011)
Geometrical product specifications (GPS) - Dimensional measuring equipment - Part 1: Callipers; Design and metrological characteristics (ISO 13385-1:2011)
ISO 13385-1:2011 provides the most important design and metrological characteristics of callipers with analogue indication [vernier scale or circular scale (dial)] and with digital indication (digital display).
Geometrische Produktspezifikation (GPS) - Längenmessgeräte - Teil 1: Messschieber; Konstruktionsmerkmale und messtechnische Anforderungen (ISO 13385-1:2011)
Dieser Teil von ISO 13385 legt die wichtigsten Konstruktionsmerkmale und messtechnischen Merkmale für
Messschieber fest:
⎯ mit Skalenanzeige: Noniusskale oder Rundskale (Skalenträger), und
⎯ mit Ziffernanzeige: Anzeigefeld.
Spécification géométrique des produits (GPS) - Équipement de mesurage dimensionnel - Partie 1: Pieds à coulisse; caractéristiques de conception et caractéristiques métrologiques (ISO 13385-1:2011)
L'ISO 13385-1:2011 fournit les caractéristiques de conception et les caractéristiques métrologiques les plus importantes des pieds à coulisse à indicateur analogique [échelle du vernier ou échelle circulaire (cadran)] et à indicateur numérique (affichage numérique).
Geometrijska specifikacija proizvoda - Oprema za merjenje dimenzij - 1. del: Kljunasta merila; konstrukcija in meroslovne karakteristike (ISO 13385-1:2011)
Ta del ISO 13385 navaja najpomembnejše konstrukcijske in meroslovne karakteristike kljunastih meril – z analognim prikazom: vernierjeva lestvica ali krožna lestvica (številčnica) in – z digitalnim prikazom: digitalni zaslon.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2011
1DGRPHãþD
SIST ISO 3599:1999
SIST ISO 6906:1999
Geometrijska specifikacija proizvoda - Oprema za merjenje dimenzij - 1. del:
Kljunasta merila; konstrukcija in meroslovne karakteristike (ISO 13385-1:2011)
Geometrical product specifications (GPS) - Dimensional measuring equipment - Part 1:
Callipers; Design and metrological characteristics (ISO 13385-1:2011)
Geometrische Produktspezifikation (GPS) - Längenmessgeräte - Teil 1: Messschieber;
Konstruktionsmerkmale und messtechnische Anforderungen (ISO 13385-1:2011)
Spécification géométrique des produits (GPS) - Équipement de mesurage dimensionnel -
Partie 1: Pieds à coulisse; caractéristiques de conception et caractéristiques
métrologiques (ISO 13385-1:2011)
Ta slovenski standard je istoveten z: EN ISO 13385-1:2011
ICS:
17.040.30 Merila Measuring instruments
17.040.40 6SHFLILNDFLMDJHRPHWULMVNLK Geometrical Product
YHOLþLQL]GHOND *36 Specification (GPS)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 13385-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2011
ICS 17.040.30
English Version
Geometrical product specifications (GPS) - Dimensional
measuring equipment - Part 1: Callipers; Design and
metrological characteristics (ISO 13385-1:2011)
Spécification géométrique des produits (GPS) - Geometrische Produktspezifikation (GPS) -
Équipement de mesurage dimensionnel - Partie 1: Pieds à Längenmessgeräte - Teil 1: Messschieber;
coulisse; caractéristiques de conception et caractéristiques Konstruktionsmerkmale und messtechnische
métrologiques (ISO 13385-1:2011) Anforderungen (ISO 13385-1:2011)
This European Standard was approved by CEN on 28 April 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 13385-1:2011: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (EN ISO 13385-1:2011) has been prepared by Technical Committee ISO/TC 213 “Dimensional
and geometrical product specifications and verification” in collaboration with Technical Committee
CEN/TC 290 “Dimensional and geometrical product specifications and verification” the secretariat of which is
held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by January 2012, and conflicting national standards shall be withdrawn at
the latest by January 2012.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 13385-1:2011 has been approved by CEN as a EN ISO 13385-1:2011 without any
modification.
INTERNATIONAL ISO
STANDARD 13385-1
First edition
2011-07-15
Geometrical product specifications
(GPS) — Dimensional measuring
equipment —
Part 1:
Callipers; Design and metrological
characteristics
Spécification géométrique des produits (GPS) — Équipement de
mesurage dimensionnel —
Partie 1: Pieds à coulisse; caractéristiques de conception et
caractéristiques métrologiques
Reference number
ISO 13385-1:2011(E)
©
ISO 2011
ISO 13385-1:2011(E)
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
ISO 13385-1:2011(E)
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Normative references.1
3 Terms and definitions .2
4 Design characteristics .2
4.1 General design and nomenclature .2
4.2 Dimensions .4
4.3 Types of indicating devices .4
4.4 Measuring faces .7
5 Metrological characteristics.7
5.1 General .7
5.2 Effect of slider locking.7
5.3 Maximum permissible error of indication (limited by MPE).7
5.4 MPE and MPL for a number of metrological characteristics .8
6 Indication in product documentation and data sheets.8
7 Proof of conformance with specifications.9
7.1 General .9
7.2 Measurement standards for the calibration of metrological characteristics.9
8 Marking.10
Annex A (informative) Error tests.11
Annex B (informative) Advice on application.14
Annex C (informative) Examples of different types of callipers.15
Annex D (informative) Examples of types of measurements .16
Annex E (informative) Data sheet (example).17
Annex F (informative) Calibration of metrological characteristics.18
Annex G (informative) Relation to the GPS matrix model .19
Bibliography.21
ISO 13385-1:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 13385-1 was prepared by Technical Committee ISO/TC 213, Dimensional and geometrical product
specifications and verification.
This first edition of ISO 13385-1, together with ISO 13385-2, cancels and replaces ISO 3599:1976 and
ISO 6906:1984, which have been technically revised.
ISO 13385 consists of the following parts, under the general title Geometrical product specifications (GPS) —
Dimensional measuring equipment:
⎯ Part 1: Callipers; Design and metrological characteristics
⎯ Part 2: Calliper depth gauges; Design and metrological characteristics
iv © ISO 2011 – All rights reserved
ISO 13385-1:2011(E)
Introduction
This part of ISO 13385 is a geometrical product specification (GPS) standard and is to be regarded as a
general GPS standard (see ISO/TR 14638). It influences chain link 5 of the chains of standards on size and
distance in the general GPS matrix.
The ISO/GPS Masterplan given in ISO/TR 14638 gives an overview of the ISO/GPS system of which this
document is a part. The fundamental rules of ISO/GPS given in ISO 8015 apply to this document and the
default decision rules given in ISO 14253-1 apply to specifications made in accordance with this document
unless otherwise indicated.
For more detailed information on the relation of this part of ISO 13385 to other standards and the GPS matrix
model, see Annex G.
INTERNATIONAL STANDARD ISO 13385-1:2011(E)
Geometrical product specifications (GPS) — Dimensional
measuring equipment —
Part 1:
Callipers; Design and metrological characteristics
1 Scope
This part of ISO 13385 provides the most important design and metrological characteristics of callipers
⎯ with analogue indication: vernier scale or circular scale (dial), and
⎯ with digital indication: digital display.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 14253-1, Geometrical Product Specifications (GPS) — Inspection by measurement of workpieces and
measuring equipment — Part 1: Decision rules for proving conformance or non-conformance with
specifications
ISO 14253-2:2011, Geometrical product specifications (GPS) — Inspection by measurement of workpieces
and measuring equipment — Part 2: Guidance for the estimation of uncertainty in GPS measurement, in
calibration of measuring equipment and in product verification
ISO 14978:2006, Geometrical product specifications (GPS) — Gen
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.