17.040.30 - Measuring instruments

This document specifies the most important design and metrological characteristics of calliper
depth gauges
— with analogue indication: vernier scale or circular scale (dial); and
— with digital indication: digital display.

This document specifies the most important design and metrological characteristics of calliper depth gauges — with analogue indication: vernier scale or circular scale (dial); and — with digital indication: digital display.

This document specifies acceptance and periodic reverification tests of CMM performance with
contacting probing systems and is only applicable to CMMs using:
— any type of contacting probing system; and
— spherical or hemispherical stylus tip(s).
NOTE CMM probing performance tests are specified by the maximum permissible errors (MPEs), due to the
impracticality of isolating the performance of the probing system from that of the CMM, even on a small artefact
such as a test sphere.
This doc...view more

This document specifies acceptance and periodic reverification tests of CMM performance with contacting probing systems and is only applicable to CMMs using:
— any type of contacting probing system; and
— spherical or hemispherical stylus tip(s).
NOTE CMM probing performance tests are specified by the maximum permissible errors (MPEs), due to the impracticality of isolating the performance of the probing system from that of the CMM, even on a small artefact such as a test sphere.
This docume...view more

This document specifies acceptance and periodic reverification tests of CMM performance with contacting probing systems and is only applicable to CMMs using: — any type of contacting probing system; and — spherical or hemispherical stylus tip(s). NOTE CMM probing performance tests are specified by the maximum permissible errors (MPEs), due to the impracticality of isolating the performance of the probing system from that of the CMM, even on a small artefact such as a test sphere. This document a...view more

This document provides the most important design and metrological characteristics of callipers - with analogue indication: vernier scale or circular scale (dial), and - with digital indication: digital display.

This document provides the most important design and metrological characteristics of callipers
— with analogue indication: vernier scale or circular scale (dial), and
— with digital indication: digital display.

This document provides the most important design and metrological characteristics of callipers — with analogue indication: vernier scale or circular scale (dial), and — with digital indication: digital display.

This document describes principles and tools to control a manufacturing process in accordance with a GPS specification. For this purpose a set of one or more complementary, independent characteristics (size, form, orientation, and location characteristics independent to each other) that correlate to the manufacturing process parameters and to the manufacturing process coordinate system established from the manufacturing datum system are used.
This document describes the concept of decomposition...view more

This document specifies the general requirements, calibration, terms and definitions of characteristics
of GPS measuring equipment, for example micrometers, callipers, gauge blocks and rotary axis form
measuring instruments. This document forms the basis for standards defining and describing the
design characteristics and metrological characteristics for measuring equipment and gives guidance
for the development and content of standards for GPS measuring equipment.
This document is intended...view more

This document specifies the general requirements, calibration, terms and definitions of characteristics of GPS measuring equipment, for example micrometers, callipers, gauge blocks and rotary axis form measuring instruments. This document forms the basis for standards defining and describing the design characteristics and metrological characteristics for measuring equipment and gives guidance for the development and content of standards for GPS measuring equipment.
This document is intended to ...view more

This document specifies the general requirements, calibration, terms and definitions of characteristics of GPS measuring equipment, for example micrometers, callipers, gauge blocks and rotary axis form measuring instruments. This document forms the basis for standards defining and describing the design characteristics and metrological characteristics for measuring equipment and gives guidance for the development and content of standards for GPS measuring equipment. This document is intended to e...view more

This document establishes complementary rules to ISO 1101 to be applied to pattern specifications and defines rules to combine individual specifications, for geometrical specifications e.g. using the symbols POSITION, SYMMETRY, LINE PROFILE and SURFACE PROFILE, as well as STRAIGHTNESS (in the case where the toleranced features are nominally coaxial) and FLATNESS (in the case where the toleranced features are nominally coplanar) as listed in Annex C.
These rules apply when a set of tolerance zon...view more

ISO 17450-4:2017 specifies general rules for quantifying GPS deviations for individual GPS characteristics.
NOTE GPS deviations can be local or global. A GPS characteristic defined from local GPS deviations is a parameter that transforms the set of local deviations into a global characteristic using a quantifying function (for more details, see Table 1).

This document establishes the rules for verifying the conformity or nonconformity with a given
tolerance for a characteristic of a workpiece (or a population of workpieces) or with a given maximum
permissible errors for a metrological characteristic of a measuring equipment, including when the
measured value falls close to the specification limits, taking measurement uncertainty into account.
This document applies to specifications defined in general GPS standards (see ISO 14638), i.e. stand...view more

ISO 14253-1:2017 establishes the rules for verifying the conformity or nonconformity with a given tolerance for a characteristic of a workpiece (or a population of workpieces) or with a given maximum permissible errors for a metrological characteristic of a measuring equipment, including when the measured value falls close to the specification limits, taking measurement uncertainty into account.
ISO 14253-1:2017 applies to specifications defined in general GPS standards (see ISO 14638), i.e. st...view more

ISO 25178-71:2017 defines Type S1 and Type S2 software measurement standards (etalons) for verifying the software of measuring instruments. It also defines the file format of Type S1 software measurement standards for the calibration of instruments for the measurement of surface texture by the areal method as defined in the areal surface texture chain of standards, chain link G.
NOTE Throughout ISO 25178-71:2017, the term "softgauge" is used as a substitute for "software measurement standard Ty...view more

ISO 25178-72:2017 defines the XML file format x3p for storage and exchange of topography and profile data.

This part of ISO 1938 specifies the most important metrological and design characteristics of reference disk gauges. This part of ISO 1938 covers linear sizes of the gauge up to 500 mm.

This Standard applies to the measurement of displacements along a line by means of extensometers carried out for geotechnical monitoring. It is to be applied in conjunction with EN ISO 22474-1.
Specifically, this Standard applies to
–   investigating soils and rocks;
–   checking geotechnical design values in connection with the Observational Design method;
–   deriving geotechnical design values (e.g. pile load test; trial tunnelling);
–   evaluating stability ahead of, during or after construction...view more