Dentistry - Filling instrument with contra angle (ISO 19715:2017)

ISO 19715:2017 specifies requirements and test methods for a filling instrument with contra angle, which is used for the restoration of teeth via the application of polymer-based restorative materials and cements. It also specifies requirements for the design, dimensions and marking.

Zahnheilkunde - Füllinstrumente mit Kontrawinkel (ISO 19715:2017)

Dieses Dokument legt Anforderungen und Prüfverfahren für ein Füllinstrument mit Kontrawinkel fest, das für die Restauration von Zähnen durch die Applikation von Füllungswerkstoffen auf Kunststoffbasis und Zementen verwendet wird. Es legt auch Anforderungen an die Konstruktion, Maße und Kennzeichnung fest.

Médecine bucco-dentaire - Instrument d'obturation à double angulation (ISO 19715:2017)

ISO 19715:2017 spécifie les exigences et méthodes d'essai relatives aux instruments d'obturation à double angulation et qui sont utilisés dans le cadre de restaurations dentaires réalisées par application de produits de restauration à base de polymères et ciments. Il spécifie également des exigences relatives à leur conception, leurs dimensions et leur marquage.

Zobozdravstvo - Instrumenti za polnjenje (ISO 19715:2017)

Ta mednarodni standard določa zahteve in povezane preskusne metode za instrumente za polnjenje z delovnimi konci s proti-naborom, ki se uporabljajo za obnovo zobovja s plastičnimi polnilnimi materiali. Določa tudi zahteve za zasnovo, dimenzije in označevanje.

General Information

Status
Published
Publication Date
23-May-2017
Technical Committee
Drafting Committee
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Due Date
24-May-2017
Completion Date
24-May-2017

Buy Standard

Standard
EN ISO 19715:2017
English language
17 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN ISO 19715:2017
01-september-2017
Zobozdravstvo - Instrumenti za polnjenje (ISO 19715:2017)
Dentistry - Filling instrument with contra angle (ISO 19715:2017)
Zahnheilkunde - Füllinstrumente mit Kontrawinkel (ISO 19715:2017)
Médecine bucco-dentaire - Instrument d'obturation à double angulation (ISO
19715:2017)
Ta slovenski standard je istoveten z: EN ISO 19715:2017
ICS:
11.060.25 =RERWHKQLþQLLQVWUXPHQWL Dental instruments
SIST EN ISO 19715:2017 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 19715:2017
---------------------- Page: 2 ----------------------
SIST EN ISO 19715:2017
EN ISO 19715
EUROPEAN STANDARD
NORME EUROPÉENNE
May 2017
EUROPÄISCHE NORM
ICS 11.060.20
English Version
Dentistry - Filling instrument with contra angle (ISO
19715:2017)

Médecine bucco-dentaire - Instrument d'obturation à Zahnheilkunde - Füllinstrumente mit Kontrawinkel

double angulation (ISO 19715:2017) (ISO 19715:2017)
This European Standard was approved by CEN on 1 March 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this

European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by

translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management

Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,

Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,

Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels

© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19715:2017 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 19715:2017
EN ISO 19715:2017 (E)
Contents Page

European foreword ....................................................................................................................................................... 3

---------------------- Page: 4 ----------------------
SIST EN ISO 19715:2017
EN ISO 19715:2017 (E)
European foreword

This document (EN ISO 19715:2017) has been prepared by Technical Committee ISO/TC 106

“Dentistry” in collaboration with Technical Committee CEN/TC 55 “Dentistry” the secretariat of which

is held by DIN.

This European Standard shall be given the status of a national standard, either by publication of an

identical text or by endorsement, at the latest by November 2017 and conflicting national standards

shall be withdrawn at the latest by November 2017.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent

rights.

According to the CEN-CENELEC Internal Regulations, the national standards organizations of the

following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,

Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,

France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,

Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,

Turkey and the United Kingdom.
Endorsement notice

The text of ISO 19715:2017 has been approved by CEN as EN ISO 19715:2017 without any modification.

---------------------- Page: 5 ----------------------
SIST EN ISO 19715:2017
---------------------- Page: 6 ----------------------
SIST EN ISO 19715:2017
INTERNATIONAL ISO
STANDARD 19715
First edition
2017-05
Dentistry — Filling instrument with
contra angle
Médecine bucco-dentaire — Instrument d’obturation à double
angulation
Reference number
ISO 19715:2017(E)
ISO 2017
---------------------- Page: 7 ----------------------
SIST EN ISO 19715:2017
ISO 19715:2017(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form

or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior

written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of

the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 19715:2017
ISO 19715:2017(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

Introduction ..................................................................................................................................................................................................................................v

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 Classification ............................................................................................................................................................................................................ 2

5 Requirements .......................................................................................................................................................................................................... 4

5.1 Dimensions ................................................................................................................................................................................................. 4

5.2 Dimensions of working end ......................................................................................................................................................... 4

5.3 Materials ....................................................................................................................................................................................................... 5

5.4 Surface finish ............................................................................................................................................................................................ 5

5.5 Handle............................................................................................................................................................................................................. 5

5.6 Designation and combination of working ends .......................................................................................................... 5

5.7 Resistance to reprocessing ........................................................................................................................................................... 5

6 Measurement and test methods ........................................................................................................................................................... 6

6.1 Dimensions ................................................................................................................................................................................................. 6

6.2 Hardness testing .................................................................................................................................................................................... 6

6.3 Surface roughness inspection .................................................................................................................................................... 6

6.4 Resistance to reprocessing test ................................................................................................................................................ 6

7 Marking .......................................................................................................................................................................................................................... 6

Annex A (informative) Designation and combinations of working ends ........................................................................ 7

Bibliography ................................................................................................................................................................................................................................ 9

© ISO 2017 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 19715:2017
ISO 19715:2017(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights.

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.