EN ISO 25178-6:2010
(Main)Geometrical product specifications (GPS) - Surface texture: Areal - Part 6: Classification of methods for measuring surface texture (ISO 25178-6:2010)
Geometrical product specifications (GPS) - Surface texture: Areal - Part 6: Classification of methods for measuring surface texture (ISO 25178-6:2010)
ISO 25178-6:2010 describes a classification system for methods used primarily for the measurement of surface texture. It defines three classes of methods, illustrates the relationships between the classes, and briefly describes specific methods.
Geometrische Produktspezifikation (GPS) - Oberflächenbeschaffenheit: Flächenhaft - Teil 6: Klassifizierung von Methoden zur Messung der Oberflächenbeschaffenheit (ISO 25178-6:2010)
Dieser Teil von ISO 25178 beschreibt ein Klassifizierungssystem für Methoden, welche vorwiegend zur
Messung der Oberflächenbeschaffenheit verwendet werden. Es legt drei Klassen von Methoden fest, stellt
den Zusammenhang zwischen diesen Klassen dar, und beschreibt kurz die spezifischen Methoden.
Spécification géométrique des produits (GPS) - État de surface: Surfacique - Partie 6: Classification des méthodes de mesurage de l'état de surface (ISO 25178-6:2010)
L'ISO 25178-6:2010 décrit un système de classification des méthodes employées principalement pour le mesurage de l'état de surface. Elle définit trois classes de méthodes, illustre la relation entre les classes et décrit brièvement les méthodes spécifiques.
Specifikacija geometrijskih veličin izdelka - Tekstura površine: ploskovna - 6. del: Klasifikacija metod za merjenje teksture površine (ISO 25178-6:2010)
Ta del ISO 25178 opisuje sistem klasifikacije metod, ki se uporabljajo predvsem za merjenje teksture površine. Opredeljuje tri razrede metod, prikazuje odnos med razredi in na kratko opisuje specifične metode.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-november-2011
6SHFLILNDFLMDJHRPHWULMVNLKYHOLþLQL]GHOND7HNVWXUDSRYUãLQH SORVNRYQDGHO
.ODVLILNDFLMDPHWRG]DPHUMHQMHWHNVWXUHSRYUãLQH ,62
Geometrical product specifications (GPS) - Surface texture: Areal - Part 6: Classification
of methods for measuring surface texture (ISO 25178-6:2010)
Geometrische Produktspezifikation (GPS) - Oberflächenbeschaffenheit: Flächenhaft -
Teil 6: Klassifizierung von Methoden zur Messung der Oberflächenbeschaffenheit (ISO
25178-6:2010)
Spécification géométrique des produits (GPS) - État de surface: surfacique - Partie 6:
Classification des méthodes de mesurage de l'état de surface (ISO 25178-6:2010)
Ta slovenski standard je istoveten z: EN ISO 25178-6:2010
ICS:
17.040.20 Lastnosti površin Properties of surfaces
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 25178-6
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2010
ICS 17.040.20
English Version
Geometrical product specifications (GPS) - Surface texture:
Areal - Part 6: Classification of methods for measuring surface
texture (ISO 25178-6:2010)
Spécification géométrique des produits (GPS) - État de Geometrische Produktspezifikation (GPS) -
surface: Surfacique - Partie 6: Classification des méthodes Oberflächenbeschaffenheit: Flächenhaft - Teil 6:
de mesurage de l'état de surface (ISO 25178-6:2010) Klassifizierung von Methoden zur Messung der
Oberflächenbeschaffenheit (ISO 25178-6:2010)
This European Standard was approved by CEN on 16 January 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 25178-6:2010: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (EN ISO 25178-6:2010) has been prepared by Technical Committee ISO/TC 213 "Dimensional
and geometrical product specifications and verification" in collaboration with Technical Committee
CEN/TC 290 “Dimensional and geometrical product specification and verification” the secretariat of which is
held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by August 2010, and conflicting national standards shall be withdrawn at
the latest by August 2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 25178-6:2010 has been approved by CEN as a EN ISO 25178-6:2010 without any
modification.
INTERNATIONAL ISO
STANDARD 25178-6
First edition
2010-02-01
Geometrical product specifications
(GPS) — Surface texture: Areal —
Part 6:
Classification of methods for measuring
surface texture
Spécification géométrique des produits (GPS) — État de surface:
Surfacique —
Partie 6: Classification des méthodes de mesurage de l'état de surface
Reference number
ISO 25178-6:2010(E)
©
ISO 2010
ISO 25178-6:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2010
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2010 – All rights reserved
ISO 25178-6:2010(E)
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Normative references.1
3 Terms and definitions .1
3.1 General terms .1
3.2 Definitions for classification of surface texture measurement methods .2
3.3 Terms and descriptions for specific methods.3
4 Classification scheme.5
Annex A (informative) Metrological limitations.8
Annex B (informative) Relation to the GPS matrix model.9
Bibliography.10
ISO 25178-6:2010(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 25178-6 was prepared by Technical Committee ISO/TC 213, Dimensional and geometrical product
specifications and verification.
ISO 25178 consists of the following parts, under the general title Geometrical product specifications (GPS) —
Surface texture: Areal:
⎯ Part 2: Terms, definitions and surface texture parameters
⎯ Part 3: Specification operators
⎯ Part 6: Classification of methods for measuring surface texture
⎯ Part 7: Software measurement standards
⎯ Part 601: Nominal characteristics of contact (stylus) instruments
⎯ Part 602: Nominal characteristics of non-contact (confocal chromatic probe) instruments
⎯ Part 603: Nominal characteristics of non-contact (phase-shifting interferometric microscopy) instruments
⎯ Part 701: Calibration and measurement standards for contact (stylus) instruments
The following parts are under preparation:
⎯ Part 604: Nominal characteristics of non-contact (coherence scanning interferometry) instruments
⎯ Part 605: Nominal characteristics of non-contact (point autofocusing) instruments
iv © ISO 2010 – All rights reserved
ISO 25178-6:2010(E)
Introduction
This part of ISO 25178 is a geometrical product specification (GPS) standard and is to be regarded as a
[2]
general GPS standard (see ISO/TR 14638 ). It influences the chain link 5 of the chain of standards on
roughness profile, waviness profile, primary profile and areal surface texture.
This part of ISO 25178 describes a classification system for methods used primarily for the measurement of
surface texture. The classification system provides a context for the development of other parts of ISO 25178
that describe characteristics and measurement standards for some of the individual methods. Such a
classification is also intended to aid in choosing and understanding various types of methods and in
determining which standards apply to their application. The classification system is aimed to be as general as
possible. However, instruments may exist that do not clearly fit within any single method class.
INTERNATIONAL STANDARD ISO 25178-6:2010(E)
Geometrical product specifications (GPS) — Surface texture:
Areal —
Part 6:
Classification of methods for measuring surface texture
1 Scope
This part of ISO 25178 describes a classification system for methods used primarily for the measurement of
surface texture. It defines three classes of methods, illustrates the relationships between the classes, and
briefly describes specific methods.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 4287:1997, Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms,
definitions and surface texture parameters
1)
ISO 25178-2:— , Geometrical product specifications (GPS) — Surface texture: Areal — Part 2: Terms,
definitions and surface texture parameters
ISO/IEC Guide 99:2007, International vocabulary of metrology — Basic and general concepts and associated
terms (VIM)
3 Terms and definitions
3.1 General terms
For the purposes of this document, the terms and definitions given in ISO 4287, ISO 25178-2,
ISO/IEC Guide 99 and the following apply.
3.1.1
measurement coordinate system
system of coordinates in which surface texture parameters are measured
NOTE 1 If the nominal surface is a plane (or portion of a plane), it is usual to use a rectangular coordinate system in
which the axes form a right-handed Cartesian set, the X-axis being the direction of tracing co-linear with the mean line and
the Y-axis also lying on the nominal surface, and the Z-axis being in an outward direction (from the material to the
surrounding medium). The rectangular coordinate system is adopted in this part of ISO 25178 except for 3.2.1, Note 3,
and 3.3.3, where a cylindrical coordinate system is described.
NOTE 2 See also specification coordinate system [ISO 25178-2:—].
1) To be published.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.