EN ISO 16610-28:2016
(Main)Geometrical product specifications (GPS) - Filtration - Part 28: Profile filters: End effects (ISO 16610-28:2016)
Geometrical product specifications (GPS) - Filtration - Part 28: Profile filters: End effects (ISO 16610-28:2016)
ISO 16610-28:2016 provides methods for treating the end effects of linear profile filters where such effects occur.
Geometrische Produktspezifikation (GPS) - Filterung - Teil 28: Profilfilter: Endeffekte (ISO 16610-28:2016)
Dieses Dokument enthält Verfahren zur Behandlung von Endeffekten bei linearen Profilfiltern im Fall ihres Auftretens.
Spécification géométrique des produits (GPS) - Filtrage - Partie 28: Filtres de profil: Effets de bords (ISO 16610-28:2016)
ISO 16610-28:2016 fournit des méthodes pour traiter les effets de bord des filtres de profil linéaire, lorsque ces effets se produisent.
Specifikacije geometrijskih veličin izdelka (GPS) - Filtriranje - 28. del: Profilni filtri: končni učinki (ISO 16610-28:2016)
Ta del standarda ISO 16610 podaja metode za popravljanje končnih učinkov linearnih profilnih filtrov, kjer se pojavljajo taki učinki.
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-marec-2017
6SHFLILNDFLMHJHRPHWULMVNLKYHOLþLQL]GHOND *36 )LOWULUDQMHGHO 3URILOQLILOWUL
NRQþQLXþLQNL ,62
Geometrical product specifications (GPS) - Filtration - Part 28: Profile filters: End effects
(ISO 16610-28:2016)
Geometrische Produktspezifikation (GPS) - Filterung - Teil 28: Profilfilter: Endeffekte
(ISO 16610-28:2016)
Spécification géométrique des produits (GPS) - Filtrage - Partie 28: Filtres de profil:
Effets de bords (ISO 16610-28:2016)
Ta slovenski standard je istoveten z: EN ISO 16610-28:2016
ICS:
17.040.20 Lastnosti površin Properties of surfaces
17.040.40 6SHFLILNDFLMDJHRPHWULMVNLK Geometrical Product
YHOLþLQL]GHOND *36 Specification (GPS)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 16610-28
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2016
EUROPÄISCHE NORM
ICS 17.040.40
English Version
Geometrical product specifications (GPS) - Filtration - Part
28: Profile filters: End effects (ISO 16610-28:2016)
Spécification géométrique des produits (GPS) - Filtrage Geometrische Produktspezifikation (GPS) - Filterung -
- Partie 28: Filtres de profil: Effets de bords (ISO Teil 28: Profilfilter: Endeffekte (ISO 16610-28:2016)
16610-28:2016)
This European Standard was approved by CEN on 19 November 2016.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 16610-28:2016 E
worldwide for CEN national Members.
Contents Page
European Foreword . 3
European Foreword
This document (EN ISO 16610-28:2016) has been prepared by Technical Committee ISO/TC 213
“Dimensional and geometrical product specifications and verification” in collaboration with Technical
Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the
secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2017, and conflicting national standards shall be
withdrawn at the latest by June 2017.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,
Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 16610-28:2016 has been approved by CEN as EN ISO 16610-28:2016 without any
modification.
INTERNATIONAL ISO
STANDARD 16610-28
First edition
2016-12-15
Geometrical product specifications
(GPS) — Filtration —
Part 28:
Profile filters: End effects
Spécification géométrique des produits (GPS) — Filtrage —
Partie 28: Filtres de profil: Effets de bords
Reference number
ISO 16610-28:2016(E)
©
ISO 2016
ISO 16610-28:2016(E)
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2016 – All rights reserved
ISO 16610-28:2016(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 End effect correction methods . 2
4.1 General . 2
4.2 Extrapolation of the profile — Methods . 4
4.2.1 Zero padding . 4
4.2.2 Linear extrapolation . 5
4.2.3 Symmetric extension . 6
4.3 Moment retainment criterion . 8
5 Recommendations .14
5.1 Default end correction .14
5.2 End correction designations .15
Annex A (normative) Filters according to ISO 16610 with automatic correction of end effects.16
Annex B (informative) Relationship to the filtration matrix model .18
Annex C (informative) Relationship to the GPS matrix model .19
Bibliography .20
ISO 16610-28:2016(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 213, Dimensional and geometrical product
specifications and verification.
This first edition of ISO 16610-28 cancels and replaces ISO/TS 16610-28:2010, which has been
technically revised.
A list of all parts in the ISO 16610 series can be found on the ISO website.
iv © ISO 2016 – All rights reserved
ISO 16610-28:2016(E)
Introduction
This document is a geometrical product specification (GPS) standard and is to be regarded as a general
GPS standard (see ISO 14638). It influences the chain link C of all chains of standards.
The ISO/GPS Matrix model given in ISO 14638 gives an overview of the ISO/GPS system of which this
document is a part. The fundamental rules of ISO/GPS given in ISO 8015 apply to this document and
the default decision rules given in ISO 14253-1 apply to specifications made in accordance with this
document, unless otherwise indicated.
For more detailed information of the relation of this document to the GPS matrix model, see Annex C.
This document develops the concept of handling end effects in the case of linear profile filters.
INTERNATIONAL STANDARD ISO 16610-28:2016(E)
Geometrical product specifications (GPS) — Filtration —
Part 28:
Profile filters: End effects
1 Scope
This document provides methods for treating the end effects of linear profile filters where such
effects occur.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 16610-1, Geometrical product specifications (GPS) — Filtration — Part 1: Overview and basic concepts
ISO 16610-20, Geometrical product specifications (GPS) — Filtration — Part 20: Linear profile filters: Basic
concepts
ISO 16610-21, Geometrical product specifications (GPS) — Filtration — Part 21: Linear profile filters:
Gaussian filters
ISO 16610-22, Geometrical product specifications (GPS) — Filtration — Part 22: Linear profile filters:
Spline filters
ISO 16610-31, Geometrical product specifications (GPS) — Filtration — Part 31: Robust profile filters:
Gaussian regression filters
ISO/TS 16610-32, Geometrical product specifications (GPS) — Filtration — Part 32: Robust profile filters:
Spline filters
ISO/IEC Guide 99, International vocabulary of metrology — Basic and general concepts and associated
terms (VIM)
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO/IEC Guide 99, ISO 16610-1,
ISO 16610-20, ISO 16610-21, ISO 16610-22, ISO 16610-31, ISO/TS 16610-32 and the fol
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.