EN ISO 10462:2013
(Main)Gas cylinders - Acetylene cylinders - Periodic inspection and maintenance (ISO 10462:2013)
Gas cylinders - Acetylene cylinders - Periodic inspection and maintenance (ISO 10462:2013)
ISO 10462:2013 specifies requirements for the periodic inspection of acetylene cylinders as required for the transport of dangerous goods and for maintenance in connection with periodic inspection. It applies to acetylene cylinders with and without solvent and with a maximum nominal water capacity of 150 l.
Gasflaschen - Acetylenflaschen - Wiederkehrende Inspektion und Wartung (ISO 10462:2013)
Diese Internationale Norm legt Anforderungen für die wiederkehrende Inspektion von Acetylenflaschen, die für den Transport von gefährlichen Gütern benötigt werden, und für die Wartung in Zusammenhang mit der wiederkehrenden Inspektion fest. Sie gilt für Acetylenflaschen mit und ohne Lösemittel und mit einem maximalen Fassungsraum von 150 l.
ANMERKUNG Die Begrenzung von 150 l wird von der Definition einer Flasche nach [1] hergeleitet.
Bouteilles à gaz - Bouteilles d'acétylène - Contrôle et entretien périodiques (ISO 10462:2013)
L'ISO 10462:2013 spécifie les exigences relatives au contrôle périodique des bouteilles d'acétylène, comme cela est exigé pour le transport des marchandises dangereuses et pour l'entretien en rapport avec le contrôle périodique. Elle s'applique aux bouteilles d'acétylène avec et sans solvant, d'une contenance en eau nominale maximale de 150 l.
Plinske jeklenke - Jeklenke za acetilen - Periodična kontrola in vzdrževanje (ISO 10462:2013)
ISO 10462 določa zahteve za periodične preglede jeklenk za acetilen, kot se zahteva za prevoz nevarnega blaga, in vzdrževanje v povezavi s periodičnimi pregledi. Velja za jeklenke za acetilen z in brez topil ter z nominalno prostornino vode 150 litrov.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2014
1DGRPHãþD
SIST EN 12863:2002
SIST EN 12863:2002/A1:2006
3OLQVNHMHNOHQNH-HNOHQNH]DDFHWLOHQ3HULRGLþQDNRQWURODLQY]GUåHYDQMH ,62
Gas cylinders - Acetylene cylinders - Periodic inspection and maintenance (ISO
10462:2013)
Gasflaschen - Acetylenflaschen - Wiederkehrende Inspektion und Wartung (ISO
10462:2013)
Bouteilles à gaz - Bouteilles d'acétylène - Contrôle et entretien périodiques (ISO
10462:2013)
Ta slovenski standard je istoveten z: EN ISO 10462:2013
ICS:
23.020.30 7ODþQHSRVRGHSOLQVNH Pressure vessels, gas
MHNOHQNH cylinders
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 10462
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2013
ICS 23.020.30 Supersedes EN 12863:2002
English Version
Gas cylinders - Acetylene cylinders - Periodic inspection and
maintenance (ISO 10462:2013)
Bouteilles à gaz - Bouteilles d'acétylène - Contrôle et Gasflaschen - Acetylenflaschen - Wiederkehrende
entretien périodiques (ISO 10462:2013) Inspektion und Wartung (ISO 10462:2013)
This European Standard was approved by CEN on 23 November 2013.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10462:2013 E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (EN ISO 10462:2013) has been prepared by Technical Committee ISO/TC 58 “Gas cylinders”
in collaboration with the Technical Committee CEN/TC 23 “Transportable gas cylinders” the secretariat of
which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2014, and conflicting national standards shall be withdrawn at
the latest by June 2014.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 12863:2002.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 10462:2013 has been approved by CEN as EN ISO 10462:2013 without any modification.
INTERNATIONAL ISO
STANDARD 10462
Third edition
2013-12-15
Gas cylinders — Acetylene cylinders —
Periodic inspection and maintenance
Bouteilles à gaz — Bouteilles d’acétylène — Contrôle et entretien
périodiques
Reference number
ISO 10462:2013(E)
©
ISO 2013
ISO 10462:2013(E)
© ISO 2013
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2013 – All rights reserved
ISO 10462:2013(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General . 3
4.1 Intervals between periodic inspections . 3
4.2 Requirements for inspection . 3
5 Preparation of the acetylene cylinder . 3
5.1 Depressurization of the acetylene cylinder. 3
5.2 Preparation for external visual inspection . 4
5.3 Removal of the valve . . 4
5.4 Removal of neck/core hole filters . 4
6 Inspection and maintenance . 5
6.1 External visual inspection . 5
6.2 Inspection of the porous material . 5
6.3 Addition of non-monolithic porous material . 6
6.4 Replacement of porous material . 7
6.5 Inspection of fusible plugs . 7
6.6 Inspection of valves . 7
6.7 Inspection of cylinder neck . 7
6.8 Reassembly. 8
7 Cylinder marking and identification . 8
8 Records . 9
9 Rejection and rendering cylinders unserviceable . 9
10 Disposal of unserviceable cylinders . 9
Annex A (informative) Tops of acetylene cylinders containing monolithic porous material .11
Annex B (normative) External visual inspection .14
Annex C (normative) Determination of the top clearance .17
Annex D (normative) Cracks in the porous material .19
Annex E (informative) Rings for indicating the date of the next periodic inspection for
gas cylinders .20
Bibliography .22
ISO 10462:2013(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received. www.iso.org/patents
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers
to Trade (TBT) see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 58, Gas cylinders, Subcommittee SC 4, Operational
requirements for gas cylinders.
This third edition cancels and replaces the second edition (ISO 10462:2005), which has been technically
revised.
The following are the main technical modifications.
a) The second edition (ISO 10462:2005) has been revised taking EN 12863 into account; EN 12863 has
been superseded by this third edition.
b) Periodic inspection periods are based on the relevant regulations and do not have to be repeated in
this International Standard, thus also avoiding possible inconsistencies in case periodic inspection
periods are changed in the regulations. Consequently, the former Annex A has been deleted and
relevant information is covered in 4.1.
c) For the removal of the valve, reference to ISO 25760 is included and, consequently, the forme
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.