EN ISO 10460:2018
(Main)Gas cylinders - Welded aluminium-alloy, carbon and stainless steel gas cylinders - Periodic inspection and testing (ISO 10460:2018, Corrected version 2019-04)
Gas cylinders - Welded aluminium-alloy, carbon and stainless steel gas cylinders - Periodic inspection and testing (ISO 10460:2018, Corrected version 2019-04)
This document specifies the requirements for the periodic inspection and testing of welded aluminium-alloy, carbon and stainless steel gas cylinders of water capacity from 0,5 l to 150 l intended for compressed and liquefied gas service under pressure and to verify the integrity of such gas cylinders for further service.
It also applies, as far as is practical, to cylinders of less than 0,5 l water capacity and greater than 150 l up to 450 l.
This document does not apply to the periodic inspection and testing of acetylene cylinders or composite (fully wrapped or hoop-wrapped) cylinders.
It is primarily intended for use with cylinders containing industrial gases other than liquefied petroleum gas (LPG). This document may also be applicable to LPG. Requirements for LPG applications are also provided in ISO 10464.
Gasflaschen - Geschweißte Gasflaschen aus Aluminiumlegierung, Kohlenstoffstahl und Edelstahl - Wiederkehrende Inspektion und Prüfung (ISO 10460:2018)
Bouteilles à gaz - Bouteilles à gaz soudées en alliage d'aluminium, carbone et acier inoxydable - Contrôles et essais périodiques (ISO 10460:2018, Version corrigée 2019-04)
Le présent document spécifie les exigences concernant les contrôles et essais périodiques des bouteilles à gaz soudées en alliage d'aluminium, carbone et acier inoxydable d'une contenance en eau de 0,5 l à 150 l, destinées au service sous pression de gaz comprimés et liquéfiés, et la vérification de l'intégrité de ce type de bouteilles à gaz pour une prolongation de leur utilisation.
Il s'applique également, dans la mesure du possible, aux bouteilles d'une contenance en eau inférieure à 0,5 l et de 150 l à 450 l.
Le présent document ne s'applique pas aux contrôles et essais périodiques des bouteilles d'acétylène ou des bouteilles composites (bouteilles bobinées composites et bouteilles frettées).
Il est destiné à être utilisé principalement pour les bouteilles contenant des gaz industriels autres que le gaz de pétrole liquéfié (GPL). Le présent document est cependant susceptible de s'appliquer au GPL. L'ISO 10464 donne également des exigences concernant les applications GPL.
Plinske jeklenke - Varjene jeklenke iz aluminijevih zlitin ter ogljikovih in nerjavnih jekel - Periodični pregledi in preskušanje (ISO 10460:2018)
Za razširitev področja uporabe standarda ISO 10460:2005 za vključitev zahtev glede rednih pregledov in preskušanja varjenih jeklenk iz aluminijevih zlitin in nerjavnega jekla ter za osvežitev seznama zvez s standardi za namene posodobitve tega standarda.
Revizija bo vključevala zahteve, ki veljajo za vse vrste valjev s področja uporabe, in posebne zahteve (po možnosti v obliki normativnih dodatkov) za določene vrste materialov valjev (npr. aluminijeve zlitine).
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2018
3OLQVNHMHNOHQNH9DUMHQHMHNOHQNHL]DOXPLQLMHYLK]OLWLQWHURJOMLNRYLKLQQHUMDYQLK
MHNHO3HULRGLþQLSUHJOHGLLQSUHVNXãDQMH ,62
Gas cylinders - Welded aluminium-alloy, carbon and stainless steel gas cylinders -
Periodic inspection and testing (ISO 10460:2018)
Gasflaschen - Geschweißte Gasflaschen aus Aluminiumlegierung, Kohlenstoff- sowie
rostfreiem Stahl - Wiederkehrende Prüfung (ISO 10460:2018)
Bouteilles à gaz - Bouteilles à gaz soudées en alliage d'aluminium, carbone et acier
inoxydable - Contrôles et essais périodiques (ISO 10460:2018)
Ta slovenski standard je istoveten z: EN ISO 10460:2018
ICS:
23.020.35 Plinske jeklenke Gas cylinders
77.150.10 Aluminijski izdelki Aluminium products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 10460
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2018
EUROPÄISCHE NORM
ICS 23.020.35
English Version
Gas cylinders - Welded aluminium-alloy, carbon and
stainless steel gas cylinders - Periodic inspection and
testing (ISO 10460:2018)
Bouteilles à gaz - Bouteilles à gaz soudées en alliage Gasflaschen - Geschweißte Gasflaschen aus
d'aluminium, carbone et acier inoxydable - Contrôles et Aluminiumlegierung, Kohlenstoffstahl und Edelstahl -
essais périodiques (ISO 10460:2018) Wiederkehrende Inspektion und Prüfung (ISO
10460:2018)
This European Standard was approved by CEN on 8 September 2018.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10460:2018 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 10460:2018) has been prepared by Technical Committee ISO/TC 58 "Gas
cylinders" in collaboration with Technical Committee CEN/TC 23 “Transportable gas cylinders” the
secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2019, and conflicting national standards shall be
withdrawn at the latest by April 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 10460:2018 has been approved by CEN as EN ISO 10460:2018 without any modification.
INTERNATIONAL ISO
STANDARD 10460
Third edition
2018-09
Gas cylinders — Welded aluminium-
alloy, carbon and stainless steel gas
cylinders — Periodic inspection and
testing
Bouteilles à gaz — Bouteilles à gaz soudées en alliage d'aluminium,
carbone et acier inoxydable — Contrôles et essais périodiques
Reference number
ISO 10460:2018(E)
©
ISO 2018
ISO 10460:2018(E)
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
ISO 10460:2018(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Intervals between periodic inspection and testing . 2
5 Periodic inspection and testing procedures . 2
5.1 General . 2
5.2 Depressurization and devalving procedures . 3
5.2.1 Depressurization . 3
5.2.2 Devalving . 3
5.3 External visual inspection . 3
5.3.1 General. 3
5.3.2 Preparation . 3
5.3.3 Procedure . 4
5.3.4 Inspection result . 4
5.4 Internal visual inspection . 5
5.4.1 General. 5
5.4.2 Preparation . 5
5.4.3 Cleaning . 5
5.4.4 Inspection result . 5
5.5 Cylinder neck inspection . 6
5.5.1 Cylinder-to-valve threads . 6
5.5.2 Other neck surfaces . 6
5.5.3 Neckring and/or collar attachment . 7
5.6 Pressure test . 7
5.6.1 General. 7
5.6.2 Test equipment . 8
5.6.3 Test criteria . 8
5.6.4 Acceptance criteria . 9
5.7 Cylinder repair . 9
5.7.1 General. 9
5.7.2 Major repairs . 9
5.7.3 Minor repairs . 9
5.8 Inspection of valve and other accessories . 9
5.9 Final operations . 9
5.9.1 Drying, cleaning, painting and coating. 9
5.9.2 Cylinder revalving .10
5.9.3 Cylinder tare check .10
5.9.4 Cylinder marking after periodic inspection and testing .10
5.9.5 Reference to next periodic inspection and testing date .11
5.9.6 Reports .11
5.10 Rejection and rendering cylinders unserviceable .11
Annex A (informative) Intervals between periodic inspections and tests .13
Annex B (informative) Gas cylinder periodic inspection date rings .14
Annex C (normative) Description and evaluation of imperfections and conditions for
rejection at visual inspection .15
An
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.