EN ISO 13337:1997

Spring-type straight pins - Slotted, light duty (ISO 13337:1997)

Spannstifte (-hülsen) - Geschlitzt, leichte Ausführung (ISO 13337:1997)

Diese Internationale Norm beschreibt die Eigenschaften von Spannstiften, geschlitzt, aus Stahl oder aus austenitischem oder martensitischem nichtrostendem Stahl, leichte Ausführung mit Nenndruckmessern d1 von 2 mm bis einschließlich 50 mm. Anmerkung: Die Nenndurchmesser wurden so gewählt, daß die Spannstifte ineinander montiert oder mit Spannstiften, schwere Ausführung, nach ISO 8752 kombiniert werden können.

Goupilles cylindriques creuses, dites goupilles élastiques - Série mince (ISO 13337:1997)

IEC 61788-22-1:2017 décrit les éléments généraux relatifs aux spécifications des capteurs et détecteurs supraconducteurs, qui sont la base des spécifications données dans les autres parties de l’IEC 61788 pour différents types de capteurs et de détecteurs. Les capteurs et détecteurs décrits sont principalement constitués de matériaux supraconducteurs et dépendent des phénomènes supraconducteurs ou relatifs. Les objets à mesurer (mesurandes) comprennent les champs magnétiques, les ondes électromagnétiques, les photons de différentes énergies, les électrons, les ions, les particules, et autres.

Valjasto zviti vzmetni zatiči - Lahka izvedba (ISO 13337:1997)

General Information

• Status: Withdrawn
• Publication Date: 14-Nov-1997
• Withdrawal Date: 14-Jun-2009
• ICS: 21.060.50 - Pins, nails
• Technical Committee: CEN/TC 185 - Threaded and nonthreaded mechanical fasteners and accessories
• Drafting Committee: CEN/TC 185 - Threaded and nonthreaded mechanical fasteners and accessories
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 15-Jun-2009
• Completion Date: 15-Jun-2009
• Ref Project: SIST EN ISO 13337:2001 - Spring-type straight pins - Slotted, light duty (ISO 13337:1997)

Relations

• Replaced By: EN ISO 13337:2009 - Spring-type straight pins - Slotted, light duty (ISO 13337:2009)
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 13337:2001
01-julij-2001
9DOMDVWR]YLWLY]PHWQL]DWLþL/DKNDL]YHGED,62
Spring-type straight pins - Slotted, light duty (ISO 13337:1997)
Spannstifte (-hülsen) - Geschlitzt, leichte Ausführung (ISO 13337:1997)
Goupilles cylindriques creuses, dites goupilles élastiques - Série mince (ISO
13337:1997)
Ta slovenski standard je istoveten z: EN ISO 13337:1997
ICS:
21.060.50 =DWLþLåHEOML Pins, nails
SIST EN ISO 13337:2001 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 13337:2001

---------------------- Page: 2 ----------------------

SIST EN ISO 13337:2001

---------------------- Page: 3 ----------------------

SIST EN ISO 13337:2001

---------------------- Page: 4 ----------------------

SIST EN ISO 13337:2001

---------------------- Page: 5 ----------------------

SIST EN ISO 13337:2001

---------------------- Page: 6 ----------------------

SIST EN ISO 13337:2001
INTERNATIONAL ISO
STANDARD 13337
First edition
1997-11-15
Spring-type straight pins — Slotted, light
duty
Goupilles cylindriques creuses, dites goupilles élastiques — Série mince
A
Reference number
ISO 13337:1997(E)

---------------------- Page: 7 ----------------------

SIST EN ISO 13337:2001
ISO 13337:1997(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide
federation of national standards bodies (ISO member bodies). The work of
preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which
a technical committee has been established has the right to be represented
on that committee. International organizations, governmental and non-
governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard ISO 13337 was prepared by Technical Committee
ISO/TC 2, Fasteners.
Annex A of this International Standard is for information only.
©  ISO 1997
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet [e-mail]
X.400 c=ch; a=400net; p=iso; o=isocs; s=central
Printed in Switzerland
ii

---------------------- Page: 8 ----------------------

SIST EN ISO 13337:2001
©
INTERNATIONAL STANDARD  ISO ISO 13337:1997(E)
Spring-type straight pins – Slotted, light duty
1 Scope
This International Standard specifies the characteristics of slotted spring-type straight pins, made of steel or of
austenitic or martensitic stainless steel, light duty with nominal diameter, d , from 2 mm to 50 mm inclusive.
1
NOTE —  The nominal diameters have been chosen in such a way that pins may be fitted one into the other
or combined with pins, heavy duty in accordance with ISO 8752.
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this
International Standard. At the time of publication, the editions indicated were valid. All standards are subject
to revision, and parties to agreements based on this International Standard are encouraged to investigate the
possibility of applying the most recent editions of the standards indicated below. Members of IEC and ISO
maintain registers of currently valid International Standards.
ISO 3269:1988, Fasteners – Acceptance inspection.
1)
ISO 4042:— , Fasteners – Electroplated coatings.
ISO 8749:1986, Pins and grooved pins – Shear test.
3 Dimensions
See figure 1 and table 1.
1) For spring pins with a nominal diameter d ≥ 10 mm a single chamfer configuration is optional at the
1
discretion of the supplier
2) d < d
3 1, nom
NOTE —  For non-interlocking spring-pins (slot type N) see clauses 5 and 6.
Figure 1
1) To be published. (Revision of ISO 4042:1989)
1

---------------------- Page: 9 ----------------------

SIST EN ISO 13337:2001
©
ISO
ISO 13337:1997(E)
Table 1 — Dimensions
nom. 2  2,5 3  3,5 4  4,5 5  6  8  10
d max. 2,4 2,9 3,5 4,0 4,6 5,1 5,6 6,7 8,8 10,8
1
before
mounting min. 2,3 2,8 3,3 3,8 4,4 4,9 5,4 6,4 8,5 10,5
d before
2
1,9 2,3 2,7 3,1 3,4 3,9 4,4 4,9 7 8,5
1)
mounting
a max. 0,4 0,45 0,45 0,5 0,7 0,7 0,7 0,9 1,
...