iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 818-4:1996

(Main)

Short link chain for lifting purposes - Safety - Part 4: Chain slings - Grade 8

Short link chain for lifting purposes - Safety - Part 4: Chain slings - Grade 8

This European Standard specifies the requirements related to safety, methods of rating and testing of single-, two-, three-, four-leg and endless chain slings assembled by:    a) mechanical joining devices;   b) welding.   using short link grade 8 medium tolerance lifting chain conforming to EN 818-2 together with the appropriate range of components of the same grade.   Note: Instructions for use and maintenance of chain slings are covered by prEN 818-6.  The hazards covered by this European Standard are identified in clause 4.  Bases for the calculation of working load limits are given in Annex B.  Annex C gives an example of a designation system for chain slings.

Kurzgliedrige Rundstahlketten für Hebezwecke - Sicherheit - Teil 4: Anschlagketten - Güteklasse 8

Diese Europäische Norm legt Anforderungen in bezug auf Sicherheit, Einstufungsmethoden und Prüfverfahren für ein-, zwei-, drei- und viersträngige Anschlagketten und für Kranzketten in a) montierter Bauart und in b) geschweißter Bauart fest, unter Benutzung von Rundstahlketten der Güteklasse 8 nach prEN 818-2 zusammen mit zugeordneten Bauteilen der gleichen Güteklasse. Anmerkung: Gebrauch und Instandhaltung von Anschlagketten ist durch prEN 818-6 abgedeckt.

Chaînes de levage à maillons courts - Sécurité - Partie 4: Elingues en chaînes - Classe 8

La présente norme européenne définit les prescriptions relatives à la sécurité, les méthodes de détermination de la charge d'utilisation et d'essai des élingues en chaînes à un, deux, trois et quatre brin(s) ainsi que les élingues sans fin assemblées par: a) dispositifs d'assemblage mécanique; b) soudage utilisant une chaîne de levage à maillons courts de classe 8, de tolérance moyenne, conforme au prEN 812-2, associée à une gamme d'accessoires adaptée de même classe. Note: Les instructions pour l'utilisation et l'entretien des élingues en chaînes sont couvertes par le prEN 818-6.

Kratkočlene okrogle verige za dvigovalne namene - Varnost - 4. del: Obešalne verige - Kakovostni razred 8

General Information

Status
Withdrawn
Publication Date
18-Jun-1996
Withdrawal Date
01-Apr-2008
ICS
53.020.30 - Accessories for lifting equipment
Technical Committee
CEN/TC 168 - Chains, ropes, webbing, slings and accessories - safaty
Drafting Committee
CEN/TC 168/WG 1 - Welded round steel link chains and chain slings
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
02-Apr-2008
Completion Date
02-Apr-2008
Directive
89/392/EEC - Machinery - Safety of machinery: general essential health and safety requirements
98/37/EC - Machinery
Mandate
M/BC/CEN/91/1 - Standardization request to CEN/CENELEC concerning machines presenting hazards due to mobility or load lifting
Ref Project
SIST EN 818-4:1999 - Short link chain for lifting purposes - Safety - Part 4: Chain slings - Grade 8

Relations

Merged Into
EN 818-4:1996+A1:2008 - Short link chain for lifting purposes - Safety - Part 4: Chain slings - Grade 8
Effective Date
18-Jan-2023
Amended By
EN 818-4:1996/prA1 - Short link chain for lifting purposes - Safety - Part 4: Chain slings - Grade 8
Effective Date
22-Dec-2008

Buy Standard

EN 818-4:1999EN 818-4:1999
PreviousNext
Standard
EN 818-4:1999
English language
27 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 818-4:1999
01-april-1999
.UDWNRþOHQHRNURJOHYHULJH]DGYLJRYDOQHQDPHQH9DUQRVWGHO2EHãDOQH
YHULJH.DNRYRVWQLUD]UHG
Short link chain for lifting purposes - Safety - Part 4: Chain slings - Grade 8
Kurzgliedrige Rundstahlketten für Hebezwecke - Sicherheit - Teil 4: Anschlagketten -
Güteklasse 8
Chaînes de levage a maillons cour
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 13411-3:2022(Main)
Terminations for steel wire ropes - Safety - Part 3: Ferrules and ferrule-securing
SIST EN 13411-3:2023

This document deals with the requirements for the ferrule-securing of eyes and endless loops.
It also deals with the requirements for ferrules for the ferrule-securing of eyes and endless loops.
This document applies to the ferrule-securing of eye terminations formed either by a Flemish eye or turn-back eye and covers ferrules made of non-alloy carbon steel and aluminium.
This document applies to slings and assemblies using steel wire ropes for general lifting applications up to and including 60 mm diameter conforming to EN 12385-4, lift ropes conforming to EN 12385-5 and spiral strand ropes conforming to EN 12385-10.
Type testing of ferrule-secured systems and manufacturing quality control requirements are also specified.
This document deals with all significant hazards, hazardous situations, and events relevant to this particular steel wire rope termination when used as intended and under conditions of use which are foreseeable by the manufacturer.
This document applies to terminations of steel wire ropes with ferrules and ferrule-securing which are manufactured after the date of this publication.
NOTE   One design of ferrule-secured turn-back eye termination using an oval aluminium ferule which satisfies the requirements of this document when securing ropes having rope grades up to and including 1960 is given for information in Annex A.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13411-7:2021(Main)
Terminations for steel wire ropes - Safety - Part 7: Symmetric wedge socket
SIST EN 13411-7:2021

This document specifies the minimum requirements for symmetrical wedge socket terminations for stranded steel wire ropes conforming to EN 12385-5 for lifts.
This document covers those symmetric wedge sockets intended for use at temperatures between −20 °C and 100 °C.
This document only covers those symmetric wedge sockets that have welded socket bodies. An example of the construction and sizes of a symmetric wedge socket is given in informative Annex A.
The informative Annex B gives the recommendations for the safe use and inspection of symmetric wedge socket according to Annex A.
This document deals with all significant hazards, hazardous situations and events relevant to symmetric wedge sockets for terminations for steel wire ropes, when used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer.
The hazards covered by this document are identified in Clause 4.
This document applies to symmetric wedge sockets, which are manufactured after the date of its publication.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13411-9:2021(Main)
Terminations for steel wire ropes - Safety - Part 9: Solid thimbles
SIST EN 13411-9:2021

This document specifies the minimum requirements for solid thimbles made of steel or cast iron for terminations of stranded steel wire ropes.
This document is applicable to ferrule-secured terminations with solid thimbles in combination with ferrules (see EN 13411-3), that have an efficiency factor KT of at least 0,9, and to spliced terminations with solid thimbles (see EN 13411-2), that have an efficiency factor KT of at least 0,8, which are used as accessories for steel wire ropes, such as slings or wire rope assemblies, having a lifting, lowering or load-bearing effect in hoisting equipment.
Examples of designs of solid thimbles which meet the requirements of this standard are given in informative Annexes B and C.
Round thimbles (thimble with rotational symmetry around the bore) are not subject to this document.
This document is applicable to ferrule-secured terminations that are manufactured after the date of publication of this document.
Hazards that are dealt with in this document are listed in Clause 4.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 3266:2010/A1:2015(Amendment)
Forged steel eyebolts grade 4 for general lifting purposes (ISO 3266:2010/Amd 1:2015)
SIST EN ISO 3266:2010/A1:2016

2014-04-02 GVN: Draft for // ENQ received at ISO/CS (see ISO notification in dataservice on 2014-04-01).

  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13411-8:2011(Main)
Terminations for steel wire ropes - Safety - Part 8: Swage terminals and swaging
SIST EN 13411-8:2012

This European Standard specifies the minimum requirements for swage terminals and the securing of such terminals by a swaging process to carbon steel rope conforming to EN 12385-4 and EN 12385-5, spiral strand rope conforming to EN 12385-10 and stainless steel stranded rope.
This European Standard is not applicable to spiral rope incorporating full lock wires - see EN 12385-10 -, nor ropes with coverings and /or fillings (see 3.6.3 of EN 12385-2:2002+A1:2008).
This European Standard is applicable to swaged terminations that have a terminal efficiency factor, KT, of at least 0,9 and are used as part of a wire rope accessory such as a sling, or wire rope assembly that performs a raising, lowering, hauling or supporting function on lifting machinery.
This European Standard is applicable to terminals of the following types that are made of carbon or stainless steel:
-   open swage socket;
-   closed swage socket;
-   swage terminal with thread;
-   swage terminal end stop.
This European Standard deals with all significant hazards, hazardous situations and events relevant to swaged terminations, when used as intended and under conditions of misuse which are reasonably foreseeable (see Clause 4).
This European Standard applies to swaged terminations which are manufactured after the date of its publication.
This European Standard is not applicable to swaged terminations used for anchoring ropes to winch drums.

  • Standard
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 3266:2010(Main)
Forged steel eyebolts grade 4 for general lifting purposes (ISO 3266:2010)
SIST EN ISO 3266:2010

ISO 3266:2010 specifies the general characteristics, performance and critical dimensions necessary for interchangeability and compatibility with other components, of forged steel eyebolts grade 4 for general lifting purposes. These eyebolts can be used for axial and inclined loading.
ISO 3266:2010 specifies the dimensions of the eyes of eyebolts permitting direct connection with shackles of the same working load limit as those defined in ISO 2415. These dimensions also allow designs with a larger eye which can permit direct connection with sling hooks of similar working load limit.
ISO 3266:2010 covers all significant hazards, hazardous situations and events relevant to eyebolts grade 4.
ISO 3266:2010 is applicable to eyebolts grade 4 for use in the temperature range of -20 ºC to 200 ºC.
ISO 3266:2010 is not applicable to eyebolts which are not forged in one piece.
ISO 3266:2010 is not applicable to forged steel eyebolts grade 4 manufactured before the date of its publication as an International Standard.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1492-1:2000+A1:2008(Main + Amendment)
Textile slings - Safety - Part 1: Flat woven webbing slings made of man-made fibres for general purpose use
SIST EN 1492-1:2001+A1:2009

This European Standard specifies the requirements related to safety, including methods of rating and testing single-, two-, three-, four-leg and endless sewn flat woven webbing slings, with or without fittings,  made of polyamide, polyester and polypropylene man-made fibre webbing in the width range of 25 mm to 450 mm inclusive.
The flat woven webbing slings covered by this Part of EN 1492 are intended for general purpose lifting operations, i.e. when used for lifting objects, materials or goods which require no deviations from the requirements, safety factors or working load limits specified. Lifting operations not covered by this standard would include the lifting of persons, potentially dangerous materials such as molten metal and acids, glass sheets, fissile materials, nuclear reactors and where special conditions apply.
Flat woven webbing slings conforming to this European Standard are suitable for use and storage in the following temperature ranges:
a)   polyester and polyamide -40°C to 100°C,
b)   polypropylene -40°C to 80°C
This European Standard does not apply to the types of webbing sling indicated below:
a)   slings such as bag slings, nets (consisting of several crossed webbings stitched together), ‘adjustable’ slings (containing, for example, intermediate buckles stitched along the webbing), etc.;
b)   slings made from webbing woven from monofilament yarns;
c)   slings designed for pre-slinging and intended not to be re-used;
This European Standard deals with the technical requirements to minimize the hazards listed in clause 4 which can arise during the use of flat woven webbing slings when carried out in accordance with the instructions and specifications given by the manufacturer or authorized representative.

  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13889:2003+A1:2008(Main + Amendment)
Forged steel shackles for general lifting purposes - Dee shackles and bow shackles - Grade 6 - Safety
SIST EN 13889:2004+A1:2009

This European Standard specifies requirements for forged steel Dee and bow shackles of grade 6 for general lifting purposes in a range of working load limits 0,5 t to 25 t maximum.
This standard applies only to those shackles with threaded pins.
Annex A gives information on the safe use of shackles, annex B gives information on types of pins, and annex C gives an example of a designation system for forged steel shackles.
The hazards covered are identified in clause 4.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1677-1:2000+A1:2008(Main + Amendment)
Components for slings - Safety - Part 1: Forged steel components, Grade 8
SIST EN 1677-1:2001+A1:2009

This Part of EN 1677 specifies general requirements for forged steel components of grade 8 up to 63 t WLL, mainly for use in:
-   chain slings according to EN 818-4;
-   steel wire rope slings according to prEN 13414-1:1999;
-   textile slings according to EN 1492-1:2000, EN 1492-2:2000
intended for lifting objects, materials or goods.
This standard does not apply to hand forged components and welded links, nor to other welded components.
The hazards covered by this Part of EN 1677 are identified in clause 4.
Annex A is informative, and gives the bases for calculation of tabulated values of mechanical properties.
Annex B is informative, and gives an example of a designation system for forged steel lifting components of grade 8.
Annex ZA gives the relationship with EU-Directives.

  • Standard
    19 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1677-6:2001+A1:2008(Main + Amendment)
Components for slings - Safety - Part 6: Links - Grade 4
SIST EN 1677-6:2001+A1:2009

Dieser Teil von EN 1677 legt Anforderungen für geschweißte Aufhänge-, Zwischen- und Endglieder und Aufhänge¬garnituren aus Stahl in Güteklasse 4 im Bereich bis 67 t Tragfähigkeit fest, die hauptsächlich Verwendung finden in:
   Anschlagketten nach EN 818 5,
   Anschlagseilen aus Stahldrahtseilen nach EN 13414 1 und
   textilen Anschlagmitteln nach EN 1492 1 und EN 1492 2,
die zum Heben von Gegenständen, Materialien und Gütern vorgesehen sind.
Die Gefährdungen, die durch diesen Teil von EN 1677 abgedeckt werden, sind in Abschnitt 4 aufgeführt.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day