FprEN ISO 16486-3
(Main)Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 3: Fittings (ISO/DIS 16486‑3:2024)
Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 3: Fittings (ISO/DIS 16486‑3:2024)
This document specifies the physical and mechanical properties of fittings made from unplasticized polyamide (PA-U) in accordance with ISO 16486‑1, intended to be buried and used for the supply of gaseous fuels.
It also specifies the test parameters for the test methods to which it refers.
The ISO 16486 series is applicable to PA-U piping systems, the components of which are connected by fusion jointing and/or mechanical jointing.
In addition, it lays down dimensional characteristics and requirements for the marking of fittings.
In conjunction with the other parts of the ISO 16486 series, this document is applicable to PA-U fittings, their joints, joints with components of PA-U and joints with mechanical fittings of other materials, and to the following fitting types:
— fusion fittings (electrofusion fittings and butt fusion fittings), and
— transition fittings.
Kunststoff-Rohrleitungssysteme für die Gasversorgung - Rohrleitungssysteme aus weichmacherfreiem Polyamid (PA-U) mit Schweißverbindungen und mechanischen Verbindungen - Teil 3: Formstücke (ISO/FDIS 16486‑3:2024)
Dieses Dokument legt die physikalischen und mechanischen Eigenschaften von Formstücken fest, die nach ISO 16486 1 aus weichmacherfreiem Polyamid (PA-U) hergestellt und dafür vorgesehen sind, unterirdisch verlegt und für die Gasversorgung verwendet zu werden.
Es legt auch die Prüfparameter für die Prüfverfahren fest, auf die es sich bezieht.
Die Normenreihe ISO 16486 ist anwendbar für PA-U-Rohrleitungssysteme, deren Komponenten durch Schweißverbindungen und/oder mechanische Verbindungen zusammengefügt werden.
Insbesondere legt dieses Dokument Maßeigenschaften und Anforderungen an die Kennzeichnung von Formstücken fest.
Zusammen mit den anderen Teilen der Normenreihe ISO 16486 gilt dieses Dokument für PA-U-Formstücke, deren Verbindungen, Verbindungen mit Komponenten aus PA-U und Verbindungen mit mechanischen Formstücken aus anderen Werkstoffen sowie für die folgenden Arten von Formstücken:
- Schweißformstücke (Heizwendelschweiß- und Stumpfschweiß-Formstücke); und
- Übergangsformstücke.
Systèmes de canalisations en matières plastiques pour la distribution de combustibles gazeux - Systèmes de canalisations en polyamide non plastifié (PA-U) avec assemblages par soudage et assemblages mécaniques - Partie 3: Raccords (ISO/DIS 16486‑3:2024)
Le présent document spécifie les propriétés physiques et mécaniques des raccords en polyamide non plastifié (PA‑U) conformément à l'ISO 16486‑1, destinés à être enterrés et utilisés pour la distribution de combustibles gazeux.
Il spécifie également les paramètres d'essai pour les méthodes d'essai auxquelles il fait référence.
La série ISO 16486 s'applique aux systèmes de canalisations en PA‑U dont les composants sont raccordés par des assemblages par soudage et/ou par des assemblages mécaniques.
De plus, elle définit les caractéristiques dimensionnelles et les exigences pour le marquage des raccords.
En conjonction avec les autres parties de la série ISO 16486, le présent document s'applique aux raccords en PA‑U, à leurs assemblages, aux assemblages avec des composants en PA‑U, aux assemblages avec des raccords mécaniques fabriqués en autres matières, ainsi qu'avec les types de raccords suivants:
— les raccords soudables (raccords électrosoudables et raccords par soudage bout à bout), et
— les raccords de transition.
Cevni sistemi iz polimernih materialov za oskrbo s plinastimi gorivi - Cevni sistemi iz nemehčanega poliamida (PA-U) z zvari in mehanskimi spoji - 3. del: Fitingi (ISO/FDIS 16486‑3:2024)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN ISO 16486-3:2024
01-junij-2024
Cevni sistemi iz polimernih materialov za oskrbo s plinastimi gorivi - Cevni sistemi
iz nemehčanega poliamida (PA-U) z zvari in mehanskimi spoji - 3. del: Fitingi
(ISO/DIS 16486-3:2024)
Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U)
piping systems with fusion jointing and mechanical jointing - Part 3: Fittings (ISO/DIS
16486-3:2024)
Kunststoff-Rohrleitungssysteme für die Gasversorgung - Rohrleitungssysteme aus
weichmacherfreiem Polyamid (PA-U) mit Schweißverbindungen und mechanischen
Verbindungen - Teil 3: Formstücke (ISO/DIS 16486-3:2024)
Systèmes de canalisations en matières plastiques pour la distribution de combustibles
gazeux - Systèmes de canalisations en polyamide non plastifié (PA-U) avec
assemblages par soudage et assemblages mécaniques - Partie 3: Raccords (ISO/DIS
16486-3:2024)
Ta slovenski standard je istoveten z: prEN ISO 16486-3
ICS:
75.200 Oprema za skladiščenje Petroleum products and
nafte, naftnih proizvodov in natural gas handling
zemeljskega plina equipment
83.140.30 Polimerne cevi in fitingi za Plastics pipes and fittings for
snovi, ki niso tekočine non fluid use
oSIST prEN ISO 16486-3:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
oSIST prEN ISO 16486-3:2024
oSIST prEN ISO 16486-3:2024
DRAFT
International
Standard
ISO/DIS 16486-3
ISO/TC 138/SC 4
Plastics piping systems for
Secretariat: NEN
the supply of gaseous fuels —
Voting begins on:
Unplasticized polyamide (PA-U)
2024-04-19
piping systems with fusion jointing
Voting terminates on:
and mechanical jointing —
2024-07-12
Part 3:
Fittings
Systèmes de canalisations en matières plastiques pour la
distribution de combustibles gazeux — Systèmes de canalisations
en polyamide non plastifié (PA-U) avec assemblages par soudage
et assemblages mécaniques —
Partie 3: Raccords
ICS: ISO ics
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Reference number
ISO/DIS 16486-3:2024(en)
oSIST prEN ISO 16486-3:2024
DRAFT
ISO/DIS 16486-3:2024(en)
International
Standard
ISO/DIS 16486-3
ISO/TC 138/SC 4
Plastics piping systems for
Secretariat: NEN
the supply of gaseous fuels —
Voting begins on:
Unplasticized polyamide (PA-U)
piping systems with fusion jointing
Voting terminates on:
and mechanical jointing —
Part 3:
Fittings
Systèmes de canalisations en matières plastiques pour la
distribution de combustibles gazeux — Systèmes de canalisations
en polyamide non plastifié (PA-U) avec assemblages par soudage
et assemblages mécaniques —
Partie 3: Raccords
ICS: ISO ics
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document is circulated as received from the committee secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
© ISO 2024
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
BE CONSIDERED IN THE LIGHT OF THEIR
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
or ISO’s member body in the country of the requester.
NATIONAL REGULATIONS.
ISO copyright office
RECIPIENTS OF THIS DRAFT ARE INVITED
CP 401 • Ch. de Blandonnet 8
TO SUBMIT, WITH THEIR COMMENTS,
CH-1214 Vernier, Geneva
NOTIFICATION OF ANY RELEVANT PATENT
Phone: +41 22 749 01 11
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/DIS 16486-3:2024(en)
ii
oSIST prEN ISO 16486-3:2024
ISO/DIS 16486-3:2024(en)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Material. 3
4.1 PA-U compound .3
4.2 Material for non-unplasticized polyamide parts .3
4.2.1 General .3
4.2.2 Metal parts .4
4.2.3 Elastomers .4
4.2.4 Other materials .4
5 General characteristics . 4
5.1 Appearance .4
5.2 Design .4
5.3 Colour .4
5.4 Electrical characteristics for electrofusion fittings .4
5.5 Appearance of factory-made fusion joints .5
5.6 Fusion compatibility .5
5.7 Appearance of transition fittings.5
6 Geometrical characteristics . 5
6.1 Measurement of dimensions .5
6.2 Dimensions of electrofusion sockets .6
6.2.1 Diameters and lengths of electrofusion sockets .6
6.2.2 Wall thickness .6
6.3 Dimensions of spigot end fittings .7
6.4 Dimensions of tapping tees .9
6.5 Dimensions of transition fittings to other materials .10
7 Mechanical characteristics .10
7.1 General .10
7.2 Conditioning.10
7.3 Mechanical requirements .10
7.4 Additional requirements for transition fittings . 13
8 Physical characteristics .13
8.1 Conditioning. 13
8.2 Requirements . 13
9 Chemical resistance of fittings in contact with chemicals .13
10 Performance requirements . .13
11 Marking . . 14
11.1 General .14
11.2 Minimum required marking of fittings .14
11.3 Additional information required on fitting or label .14
11.4 Fusion system recognition .14
12 Delivery conditions .15
Annex A (informative) Examples of typical terminal connections for electrofusion .16
Annex B (normative) Short-term pressure test method .18
Annex C (normative) Tensile test fitting/pipe assemblies .20
Bibliography .21
©
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.