EN ISO 15750-3:2008
(Main)Packaging - Steel drums - Part 3: Inserted flange-type closure systems (ISO 15750-3:2002)
Packaging - Steel drums - Part 3: Inserted flange-type closure systems (ISO 15750-3:2002)
This part of ISO 15750 specifies the characteristics, dimensions and finish of the inserted flange-type closure systems used for steel drums.
Verpackung - Stahlfässer - Teil 3: Verschlusssysteme mit eingesetztem Flansch (ISO 15750-3:2002)
Dieser Teil von ISO 15750 legt die Eigenschaften, Maße und Beschaffenheit von Verschlusssystemen mit
eingesetztem Flansch für Stahlfässer fest.
Emballages - Fûts en acier - Partie 3: Systèmes de fermeture à collerette (filetée) sertie (ISO 15750-3:2002)
La présente partie de l'ISO 15750 spécifie les caractéristiques, les dimensions et le fini des systèmes de fermeture à collerette (filetée) sertie utilisés pour les fûts en acier.
Embalaža - Jekleni sodi - 3. del: Sistemi zapiranja z vstavljenim obročem (ISO 15750-3:2002)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2008
(PEDODåD-HNOHQLVRGLGHO 6LVWHPL]DSLUDQMD]YVWDYOMHQLPREURþHP ,62
Packaging - Steel drums - Part 3: Inserted flange-type closure systems (ISO 15750-
3:2002)
Verpackung - Stahlfässer - Teil 3: Verschlusssysteme mit eingesetztem Flansch (ISO
15750-3:2002)
Emballages - Futs en acier - Partie 3: Systemes de fermeture a collerette (filetée) sertie
(ISO 15750-3:2002)
Ta slovenski standard je istoveten z: EN ISO 15750-3:2008
ICS:
55.140 6RGL.RYLQVNLVRGL5RþNH Barrels. Drums. Canisters
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 15750-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2008
ICS 55.140
English Version
Packaging - Steel drums - Part 3: Inserted flange-type closure
systems (ISO 15750-3:2002)
Emballages - Fûts en acier - Partie 3: Systèmes de Verpackung - Stahlfässer - Teil 3: Verschlusssysteme mit
fermeture à collerette (filetée) sertie (ISO 15750-3:2002) eingesetztem Flansch (ISO 15750-3:2002)
This European Standard was approved by CEN on 16 May 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15750-3:2008: E
worldwide for CEN national Members.
Contents Page
Foreword.3
Foreword
The text of ISO 15750-3:2002 has been prepared by Technical Committee ISO/TC 122 “Packaging” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 15750-3:2008 by
Technical Committee CEN/TC 261 “Packaging” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by December 2008, and conflicting national standards shall be withdrawn
at the latest by December 2008.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 15750-3:2002 has been approved by CEN as a EN ISO 15750-3:2008 without any
modification.
INTERNATIONAL ISO
STANDARD 15750-3
First edition
2002-04-15
Packaging — Steel drums —
Part 3:
Inserted flange-type closure systems
Emballages — Fûts en acier —
Partie 3: Systèmes de fermeture à collerette (filetée) sertie
Reference number
ISO 15750-3:2002(E)
©
ISO 2002
ISO 15750-3:2002(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2002
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2002 – All rights reserved
ISO 15750-3:2002(E)
Contents Page
Foreword.iv
1 Scope .1
2 Normative references.1
3 Terms and definitions .1
4 Dimensions, materials and finish .2
5 Design and construction.2
5.1 Flanges .2
5.2 Plugs .2
5.3 Capseals and overseals.3
5.4 Label rings and protection rings.3
Annex A (normative) Octagonal base closure system (type A closure) .4
Annex B (normative) Serrated base closure system (type B closure) .17
Annex C (normative) Octagonal(G 2)/hexagonal (G 3/4) base closure system (type C closure).27
Annex D (informative) Plug wrench adaptors .37
Annex E (informative) Closing torques.41
Bibliography.43
ISO 15750-3:2002(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted
by the technical committees are circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 15750 may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 15750-3 was prepared by Technical Committee ISO/TC 122, Packaging.
ISO 15750 consists of the following parts, under the general title Packaging — Steel drums:
— Part 1: Removable head (open head) drums with a minimum total capacity of 208 l, 210 l and 216,5 l
— Part 2: Non-removable head (tight head) drums with a minimum total capacity of 212 l, 216,5 l and 230 l
— Part 3: Inserted flange-type closure systems
Annexes A to C form a normative part of this part of ISO 15750. Annexes D and E are for information only.
iv © ISO 2002 – All rights reserved
INTERNATIONAL STANDARD ISO 15750-3:2002(E)
Packaging — Steel drums —
Part 3:
Inserted flange-type closure systems
1 Scope
This part of ISO 15750 specifies the characteristics, dimensions and finish of the inserted flange-type closure
systems used for steel drums.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this part of ISO 15750. For dated references, subsequent amendments to, or revisions of, any of these publications
do not apply. However, parties to agreements based on this part of ISO 15750 are encouraged to investigate the
possibility of applying the most recent editions of the normative documents indicated below. For undated
references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain
registers of currently valid International Standards.
ISO 228-1, Pipe threads where pressure-tight joints are not made on the threads — Part 1: Dimensions, tolerances
and designation
ISO 228-2, Pipe threads where pressure-tight joints are not made on the threads — Part 2: Verification by means
of limit gauges
ISO 301, Zinc alloy ingots intended for casting
ISO 3573, Hot-rolled carbon steel sheet of commercial and drawing qualities
ISO 3574, Cold-reduced carbon steel sheet of commercial and drawing qualities
ISO 5002, Hot-rolled and cold-reduced electrolytic zinc-coated carbon steel sheet of commercial and drawing
qualities
ISO 11949, Cold reduced electrolytic tinplate
ISO 11950, Cold reduced electrolytic chromium/chromium oxide-coated steel
3 Terms and definitions
For the purposes of this part of ISO 15750, the following terms and definitions apply.
3.1
inserted flange-type closure
mechanical fixed steel insert with threads, closable with plugs made of steel, other metals or synthetic materials
such as plastics, ensuring a leaktight closing in drums
ISO 15750-3:2002(E)
3.2
elastomer
macromolecular material which returns rapidly to its initial dimensions and shape after substantial deformation by a
weak stress and release of the stress
[ISO 472:1999]
3.3
thermoplastics
plastics that are capable of being repeatedly softened by heating and hardened by cooling through a temperature
range characteristic of the plastics and, in the softened state, of being repeatedly shaped by flow into articles by
moulding, extrusion or forming
4 Dimensions, materials and finish
4.1 The nominal pitch diameter and the pitch of the thread of the closures G 2 and G 3/4 shall conform to
ISO 228-1.
These closures shall fit GO gauges conforming to ISO 228-2.
4.2 The dimensions and materials of the closure systems shall be in accordance with the relevant annexes for
the closure type, i.e.:
annex A: octagonal base closure system (type A closure);
annex B: serrated base closure system (type B closure);
annex C: octagonal (G 2)/hexagonal (G 3/4) base closure system (type C closure).
4.3 The finish of the flanges, steel plugs, label rings and protection rings shall be electrolytically zinc plated.
If for reasons of compatibility another finish of the closure system is required, the nature of the internal and external
finish should be agreed upon between the purchaser and supplier.
5 Design and construction
5.1 Flanges
The flanges shall be the mechanical inserted type and shall make a leaktight fit when inserted.
5.2 Plugs
The plugs shall be designed so that they can be inserted or removed by means of a simple tool.
The plugs shall have a wrenching insert projection welded to the bottom of the sump of the plug or have a
wrenching device formed as part of the plug.
The dimensions of the wrenching insert shall be such that
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.