EN 6141:2020

Aerospace series - Plug, protective, non-metallic, for EN 6123 fitting ends

This document specifies the dimensions, tolerances and required characteristics of protective plugs, non metallic, for EN 6123 fitting ends to seal fluid ports during transportation and storage in order to prevent
- contamination by moisture, fluids, chemicals and particles,
- spillage inside package or aircraft section,
- port and pipe end damages and
- port and pipe clogging due to plug ingestion.
Because of the cleanliness requirements, parts shall only be used once.

Luft- und Raumfahrt - Stopfen, nicht metallisch, zum Schutz für Endfittinge nach EN 6123

In diesem Dokument werden die Maße, Toleranzen und erforderlichen Kennwerte von nichtmetallischen Stopfen zum Schutz für Endfittinge nach EN 6123 festgelegt, mit denen Fluidanschlüsse während des Transports und der Aufbewahrung verschlossen werden, um Folgendes zu verhindern:
- Verunreinigung durch Feuchtigkeit, Fluide, Chemikalien und Partikel;
- Leckage innerhalb der Verpackung oder einer Luftfahrzeugsektion;
- Beschädigung an Anschlüssen und Rohrenden; und
- Verstopfung von Anschlüssen und Rohren aufgrund des Ansaugens von Stopfen.
Wegen der Reinheitsanforderungen dürfen die Teile stets nur einmal verwendet werden.

Série aérospatiale - Fiche, de protection, non métallique, pour raccords EN 6123

Le présent document spécifie les dimensions, les tolérances et les caractéristiques requises pour les fiches de protection, non métalliques, pour raccords EN 6123, destinées à l’étanchéité des orifices pour les liquides pendant le transport et le stockage afin d’éviter :
- une contamination par moisissure, fluides, produits chimiques et particules,
- un renversement à l’intérieur de l’emballage ou de la section de l’aéronef,
- des endommagements des orifices et de l'extrémité des tuyaux, et
- le bouchage des orifices et des tuyaux à cause de l'absorption de la fiche.
En raison des exigences de propreté, les pièces ne doivent être utilisées qu’une seule fois.

Aeronavtika - Vtič, zaščita, nekovinska, za končno vgradnjo po EN 6123

General Information

• Status: Published
• Publication Date: 15-Sep-2020
• Withdrawal Date: 30-Mar-2021
• ICS: 49.080 - Aerospace fluid systems and components
• Technical Committee: ASD-STAN - Aerospace
• Drafting Committee: ASD-STAN/D 3/S 3 - Hydraulics
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 16-Sep-2020
• Completion Date: 16-Sep-2020
• Ref Project: SIST EN 6141:2020 - Aerospace series - Plug, protective, non-metallic, for EN 6123 fitting ends

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 6141:2020
01-november-2020
Aeronavtika - Vtič, zaščita, nekovinska, za končno vgradnjo po EN 6123
Aerospace series - Plug, protective, non-metallic, for EN 6123 fitting ends
Luft- und Raumfahrt - Stopfen, nicht metallisch, zum Schutz für Endfittinge nach EN
6123
Série aérospatiale - Prise, protectrice,non métallique pour raccord 5 000 PSI
circuits hydrauliques
Ta slovenski standard je istoveten z: EN 6141:2020
ICS:
49.080 Letalski in vesoljski Aerospace fluid systems and
hidravlični sistemi in deli components
SIST EN 6141:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 6141:2020

---------------------- Page: 2 ----------------------
SIST EN 6141:2020


EN 6141
EUROPEAN STANDARD

NORME EUROPÉENNE

September 2020
EUROPÄISCHE NORM
ICS 49.080
English Version

Aerospace series - Plug, protective, non-metallic, for EN
6123 fitting ends
Série aérospatiale - Fiche, de protection, non Luft- und Raumfahrt - Stopfen, nicht metallisch, zum
métallique, pour raccords EN 6123 Schutz für Endfittinge nach EN 6123
This European Standard was approved by CEN on 22 December 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 6141:2020 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 6141:2020
EN 6141:2020 (E)
Contents
Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Requirements . 5
4.1 Configuration, dimensions, tolerances and mass . 5
4.2 Material, surface treatment and colour . 5
4.3 Sealing areas . 5
4.4 Proof Pressure . 5
4.5 Temperature range . 5
4.5.1 Storage and transportation temperature . 5
4.5.2 Installation and removal . 5
4.5.3 Cleanliness . 5
5 Technical requirement.
...