Anodizing of aluminium and its alloys - Check for continuity of thin anodic oxidation coatings - Copper sulfate test (ISO 2085:2018)

This document specifies a method for checking the continuity of thin anodic oxidation coatings on aluminium and its alloys by a copper sulfate contact test.
The use of this method is limited to anodic oxidation coatings of thickness less than 5 µm or coatings that have been deformed, which includes those produced by coil anodizing techniques.
NOTE The method described enables a rapid check to be made for the continuity of a thin coating of aluminium oxidation on aluminium and its alloys. In cases of doubt regarding a visible fault on the surface of a coating, the use of this method makes it possible to verify whether the fault corresponds to a local gap in the coating that exposes bare metal.

Anodisieren von Aluminium und Aluminiumlegierungen - Prüfung der Kontinuität dünner anodisch erzeugter Oxidschichten - Kupfersulfatversuch (ISO 2085:2018)

Anodisation de l'aluminium et de ses alliages - Contrôle de la continuité des couches anodiques minces - Essai au sulfate de cuivre (ISO 2085:2018)

Le présent document spécifie une méthode de contrôle de la continuité des couches anodiques minces sur l'aluminium et ses alliages par essai au sulfate de cuivre.
L'utilisation de cette méthode est limitée aux couches anodiques de moins de 5 μm d'épaisseur ou à celles ayant subi une déformation, ce qui inclut celles obtenues par des techniques d'anodisation de bandes en continu.
NOTE La méthode décrite permet un contrôle rapide de la continuité de la couche mince d'oxyde sur l'aluminium et ses alliages. Ainsi, en cas de doute sur la présence d'un défaut visible à la surface de la couche, cette méthode permet de vérifier si ce défaut peut correspondre à un manque local de couche laissant le métal à nu.

Anodizacija aluminija in aluminijevih zlitin - Kontrola zveznosti tanke anodizirane plasti - Preskus z bakrovim sulfatom (ISO 2085:2018)

Ta dokument določa metodo za preverjanje neprekinjenosti tanke anodizirane plasti na aluminiju in aluminijevih zlitinah s kontaktnim preskusom z bakrovim sulfatom.
Uporaba te metode je omejena na anodizirane plasti z debelino manj kot 5 μm ali poškodovanih plasti, kar vključuje plasti, ustvarjene s tehnikami anodizacije tuljave.
OPOMBA: Opisana metoda omogoča hitro preverjanje neprekinjenosti tanke plasti aluminijske oksidacije na aluminiju in aluminijevih zlitinah. V primeru dvoma glede vidne poškodbe na površini plasti je s to metodo mogoče preveriti, ali se poškodba ujema z lokalno odprtino v plasti, ki izpostavlja golo kovino.

General Information

Status
Published
Publication Date
25-Sep-2018
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Due Date
26-Sep-2018
Completion Date
26-Sep-2018

RELATIONS

Buy Standard

Standard
EN ISO 2085:2018
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN ISO 2085:2018
01-december-2018
1DGRPHãþD
SIST EN ISO 2085:2011

Anodizacija aluminija in aluminijevih zlitin - Kontrola zveznosti tanke anodizirane

plasti - Preskus z bakrovim sulfatom (ISO 2085:2018)

Anodizing of aluminium and its alloys - Check for continuity of thin anodic oxidation

coatings - Copper sulfate test (ISO 2085:2018)

Anodisieren von Aluminium und Aluminiumlegierungen - Prüfung der Kontinuität dünner

anodisch erzeugter Oxidschichten - Kupfersulfatversuch (ISO 2085:2018)

Anodisation de l'aluminium et de ses alliages - Contrôle de la continuité des couches

anodiques minces - Essai au sulfate de cuivre (ISO 2085:2018)
Ta slovenski standard je istoveten z: EN ISO 2085:2018
ICS:
25.220.20 Površinska obdelava Surface treatment
77.120.10 Aluminij in aluminijeve zlitine Aluminium and aluminium
alloys
SIST EN ISO 2085:2018 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 2085:2018
---------------------- Page: 2 ----------------------
SIST EN ISO 2085:2018
EN ISO 2085
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2018
EUROPÄISCHE NORM
ICS 25.220.20 Supersedes EN ISO 2085:2010
English Version
Anodizing of aluminium and its alloys - Check for
continuity of thin anodic oxidation coatings - Copper
sulfate test (ISO 2085:2018)

Anodisation de l'aluminium et de ses alliages - Contrôle Anodisieren von Aluminium und

de la continuité des couches anodiques minces - Essai Aluminiumlegierungen - Prüfung der Kontinuität

au sulfate de cuivre (ISO 2085:2018) dünner anodisch erzeugter Oxidschichten -
Kupfersulfatversuch (ISO 2085:2018)
This European Standard was approved by CEN on 20 September 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this

European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by

translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management

Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,

Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,

Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 2085:2018 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 2085:2018
EN ISO 2085:2018 (E)
Contents Page

European foreword ....................................................................................................................................................... 3

---------------------- Page: 4 ----------------------
SIST EN ISO 2085:2018
EN ISO 2085:2018 (E)
European foreword

This document (EN ISO 2085:2018) has been prepared by Technical Committee ISO/TC 79 "Light

metals and their alloys" in collaboration with Technical Committee CEN/TC 132 “Aluminium and

aluminium alloys” the secretariat of which is held by AFNOR.

This European Standard shall be given the status of a national standard, either by publication of an

identical text or by endorsement, at the latest by March 2019, and conflicting national standards shall

be withdrawn at the latest by March 2019.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CEN shall not be held responsible for identifying any or all such patent rights.

This document supersedes EN ISO 2085:2010.

According to the CEN-CENELEC Internal Regulations, the national standards organizations of the

following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,

Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,

France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,

Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,

Turkey and the United Kingdom.
Endorsement notice

The text of ISO 2085:2018 has been approved by CEN as EN ISO 2085:2018 without any modification.

---------------------- Page: 5 ----------------------
SIST EN ISO 2085:2018
---------------------- Page: 6 ----------------------
SIST EN ISO 2085:2018
INTERNATIONAL ISO
STANDARD 2085
Third edition
2018-08
Anodizing of aluminium and its
alloys — Check for continuity of thin
anodic oxidation coatings — Copper
sulfate test
Anodisation de l'aluminium et de ses alliages — Contrôle de la
continuité des couches anodiques minces — Essai au sulfate de cuivre
Reference number
ISO 2085:2018(E)
ISO 2018
---------------------- Page: 7 ----------------------
SIST EN ISO 2085:2018
ISO 2085:2018(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2018

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting

on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 2085:2018
ISO 2085:2018(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 Principle ........................................................................................................................................................................................................................ 1

5 Reagents ........................................................................................................................................................................................................................ 2

6 Test area ........................................................................................................................................................................................................................ 2

6.1 Sampling ....................................................................................................................................................................................................... 2

6.2 Size and shape ......................................................................................................................................................................................... 2

6.3 Treatment before testing ......................................................................................................................................

...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.