EN ISO 15245-1:2021
(Main)Gas cylinders - Parallel threads for connection of valves to gas cylinders - Part 1: Specification (ISO 15245-1:2021)
Gas cylinders - Parallel threads for connection of valves to gas cylinders - Part 1: Specification (ISO 15245-1:2021)
This document specifies definitions, dimensions and tolerances of parallel screw threads of M30 x 2, M25 x 2 and M18 x 1,5, for the connection of valves to medical and industrial gas cylinders.
This document does not contain the connection requirements for:
— mechanical strength;
— gas tightness;
— capability of repeated assembly and dismounting operations (this aspect is covered in ISO 13341).
Ortsbewegliche Gasflaschen - Zylindrische Gewinde für den Anschluss von Ventilen an Gasflaschen - Teil 1: Spezifikation (ISO 15245-1:2021)
Dieses Dokument legt Begriffe, Maße und Toleranzen für zylindrische Gewinde M30 × 2, M25 × 2 und M18 × 1,5 für den Anschluss von Ventilen an Gasflaschen für den medizinischen und industriellen Gebrauch fest.
Dieses Dokument enthält keine Anforderungen an die Verbindung hinsichtlich
- der mechanischen Festigkeit,
- der Gasdichtheit, und
- der Fähigkeit, eine Reihe von Montagen und Demontagen unbeschadet zu überstehen (dieser Aspekt wird in ISO 13341 behandelt).
Bouteilles à gaz - Filetages parallèles pour le raccordement des robinets sur les bouteilles à gaz - Partie 1: Spécification (ISO 15245-1:2021)
Le présent document spécifie les définitions, les dimensions et les tolérances des filetages parallèles M30 x 2, M25 x 2 et M18 x 1,5, destinés au raccordement des robinets sur des bouteilles à gaz médicales ou industrielles.
Le présent document ne spécifie pas les exigences de raccordement pour les éléments suivants:
— la résistance mécanique;
— l’étanchéité au gaz;
— la capacité à répéter les opérations de montage et de démontage (cet aspect est couvert par l’ISO 13341).
Plinske jeklenke - Cilindrični navoji za priključitev ventilov na plinske jeklenke - 1. del: Specifikacija (ISO 15245-1:2021)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2021
Nadomešča:
SIST EN ISO 15245-1:2002
SIST EN ISO 15245-1:2002/A1:2013
Plinske jeklenke - Cilindrični navoji za priključitev ventilov na plinske jeklenke - 1.
del: Specifikacija (ISO 15245-1:2021)
Gas cylinders - Parallel threads for connection of valves to gas cylinders - Part 1:
Specification (ISO 15245-1:2021)
Ortsbewegliche Gasflaschen - Zylindrische Gewinde für den Anschluss von Ventilen an
Gasflaschen - Teil 1: Spezifikation (ISO 15245-1:2021)
Bouteilles à gaz - Filetages parallèles pour le raccordement des robinets sur les
bouteilles à gaz - Partie 1: Spécification (ISO 15245-1:2021)
Ta slovenski standard je istoveten z: EN ISO 15245-1:2021
ICS:
21.040.30 Posebni navoji Special screw threads
23.020.35 Plinske jeklenke Gas cylinders
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 15245-1
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2021
EUROPÄISCHE NORM
ICS 23.020.35 Supersedes EN ISO 15245-1:2001, EN ISO 15245-
1:2001/A1:2013
English Version
Gas cylinders - Parallel threads for connection of valves to
gas cylinders - Part 1: Specification (ISO 15245-1:2021)
Bouteilles à gaz - Filetages parallèles pour le Ortsbewegliche Gasflaschen - Zylindrische Gewinde für
raccordement des robinets sur les bouteilles à gaz - den Anschluss von Ventilen an Gasflaschen - Teil 1:
Partie 1: Spécification (ISO 15245-1:2021) Spezifikation (ISO 15245-1:2021)
This European Standard was approved by CEN on 16 May 2021.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15245-1:2021 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 15245-1:2021) has been prepared by Technical Committee ISO/TC 58 "Gas
cylinders" in collaboration with Technical Committee CEN/TC 23 “Transportable gas cylinders” the
secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2021, and conflicting national standards
shall be withdrawn at the latest by December 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 15245-1:2001.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 15245-1:2021 has been approved by CEN as EN ISO 15245-1:2021 without any
modification.
INTERNATIONAL ISO
STANDARD 15245-1
Second edition
2021-05
Gas cylinders — Parallel threads
for connection of valves to gas
cylinders —
Part 1:
Specification
Bouteilles à gaz — Filetages parallèles pour le raccordement des
robinets sur les bouteilles à gaz —
Partie 1: Spécification
Reference number
ISO 15245-1:2021(E)
©
ISO 2021
ISO 15245-1:2021(E)
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved
ISO 15245-1:2021(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Requirements . 3
4.1 Thread rotation . 3
4.2 Thread profile . 3
4.3 Pitch . 4
4.4 Thread dimensions . 6
4.5 O-rings . 6
5 Thread end finish . 7
6 Marking . 7
Bibliography . 8
ISO 15245-1:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 58, Gas cylinders, Subcommittee SC 2,
Cylinder fittings, in collaboration with the European Committee for Standardization (CEN) Technical
Committee CEN/TC 23, Transportable gas cylinders, in accordance with the Agreement on technical
cooperation between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 15245-1:2001), which has been technically
revised. It also incorporates the Amendment ISO 15245-1:2001/Amd.1:2013.
The main changes compared to the previous edition are as follows:
— modification of Figure 2;
— addition of subclause 4.5;
— minor editorial changes throughout the document to fully align with ISO/IEC Directives Part 2.
A list of all parts in the ISO 15245 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2021 – All rights reserved
ISO 15245-1:2021(E)
Introduction
Cylinders intended to contain compressed, liquefied or dissolved gas under pressure are fitted with
accessories (valves, straight or angle fittings) to allow release of and refilling with gas. In this document,
the term “valve” applies to such accessories.
The connection between cylinder and valve is obtained by the assembly of two parallel threads with
the same nominal pitch and thread profile – an external one on the valve stem and an internal one in
the cylinder neck – and an O-ring seal.
INTERNATIONAL STANDARD ISO 15245-1:2021(E)
Gas cylinders — Parallel threads for connection of valves to
gas cylinders —
Part 1:
Specification
1 Scope
This document specifies definitions, dimensions and tolerances of parallel screw threads of M30 x 2,
M25 x 2 and M18 x 1,5, for the connection of valves to medical and industrial gas cylinders.
This document does not contain the connection requirements for:
— mechanical strength;
— gas tightness;
— capability of repeated assembly and dismounting operations (this aspect is covered in ISO 13341).
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 724, ISO general-purpose metric screw threads — Basic dimensions
ISO 5408, Screw threads — Vocabulary
ISO 10286, Gas cylinders — Terminology
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 10286, ISO 5408 and the
following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at http:// www .electropedia .org/
3.1
valve stem
parallel sided end of valve body, with a thread formed on the external surface with a plain machined
section close to the flange on the valve body for O-ring seating and seal
Note
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.