FprEN 15012

Plastics piping systems - Non pressure soil and waste discharge piping components within the building structure - Requirements and test/assessment methods for pipes and fittings

This European Standard specifies requirements for non-pressure plastics pipes and fittings for soil and waste applications.
It is intended to be used in soil and waste discharge applications:
- inside the building (application area code "B"),
- buried in ground within the building structure (application area code "BD") and with a diameter greater than or equal to 75 mm
It gives the associated test/assessment methods.
This standard does not cover adhesives, joint sealings and gaskets
NOTE      For this standard, the term fitting includes the term joint as meant by mandate M131.

Kunststoff-Rohrleitungssysteme - Drucklose Rohrleitungssysteme zum Ableiten von Abwasser innerhalb der Gebäudestruktur - Anforderungen und Prüf-/Bewertungsverfahren für Rohre und Formstücke

Diese Europäische Norm legt Anforderungen für Rohre und Formstücke aus Kunststoff für drucklose Rohr-leitungs¬systeme zum Ableiten von Abwasser fest.
Sie gilt für Abwasseranwendungen:
-   innerhalb von Gebäuden (Anwendungskennzeichen „B“);
-   erdverlegt innerhalb der Gebäudestruktur (Anwendungskennzeichen „BD“) mit einem Durchmesser  75 mm.
Sie enthält die erforderlichen Prüf-/Bewertungsverfahren.
Diese Norm gilt nicht für Klebstoffe, Abdichtungen von Verbindungen und Dichtungen.
ANMERKUNG   Für die Anwendung dieser Norm beinhaltet der Begriff „Formstück“ den Begriff „Verbindung“ im Sinne von Mandat M131.

Systèmes de canalisations en plastique - Composants de canalisations pour l'évacuation des eaux-vannes et des eaux usées à l'intérieur de la structure des bâtiments - Exigences et méthodes d'essai/d'évaluation pour tubes et raccords

La présente Norme européenne spécifie les exigences relatives aux tubes et raccords en plastique, sans pression, destinés aux applications pour eaux-vannes et eaux usées.
Elle est destinée aux applications d’évacuation des eaux-vannes et des eaux usées :
-   à l'intérieur du bâtiment (code de zone d'application « B ») .
-   enterrées dans la structure du bâtiment (code de zone d'application « BD ») et de diamètre supérieur ou égal à 75 mm.
Elle indique les méthodes d’essai/d’évaluation associées.
La présente norme ne couvre pas les adhésifs, les garnitures de joints et les joints d’étanchéité.
NOTE   Pour la présente norme, le terme « raccord » inclut le terme « joint » au sens donné par le mandat M/131.

Cevni sistemi iz polimernih materialov - Odvodne cevne komponente brez tlaka v zgradbah - Zahteve in preskusi/metode ocenjevanja za cevi in fitinge

General Information

• Status: Not Published
• Publication Date: 10-Sep-2012
• ICS: 23.040.01 - Pipeline components and pipelines in general
• ICS: 91.140.80 - Drainage systems
• Technical Committee: CEN/TC 155 - Plastics piping systems and ducting systems
• Drafting Committee: CEN/TC 155 - Plastics piping systems and ducting systems
• Current Stage: 4598 - Decision to abandon - Finalization for Vote
• Start Date: 09-Oct-2012
• Completion Date: 09-Oct-2012
• Directive: 305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
• Directive: 89/106/EEC - Construction products
• Mandate: M/131 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on pipes, tanks and ancillaries, not in contact with water intended for human consumption
• Ref Project: oSIST prEN 15012:2011 - Plastics piping systems - Non pressure soil and waste discharge piping components within the building structure - Requirements and test/assessment methods for pipes and fittings

Relations

• Revises: EN 15012:2007 - Plastics piping systems - Soil and waste discharge systems within the building structure - Performance characteristics for pipes, fittings and their joints
• Effective Date: 18-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
01-junij-2011
Cevni sistemi iz polimernih materialov - Odvodne cevne komponente brez tlaka v
zgradbah - Zahteve in preskusi/metode ocenjevanja za cevi in fitinge
Plastics piping systems - Non pressure soil and waste discharge piping components
within the building structure - Requirements and test/assessment methods for pipes and
fittings
Kunststoff-Rohrleitungssysteme - Drucklose Rohrleitungssysteme zum Ableiten von
Abwasser innerhalb der Gebäudestruktur - Anforderungen und Prüf
-/Bewertungsverfahren für Rohre und Formstücke
Systèmes de canalisations en plastique - Composants de canalisations pour l'évacuation
des eaux-vannes et des eaux usées à l'intérieur de la structure des bâtiments -
Exigences et méthodes d'essai/d'évaluation pour tubes et raccords
Ta slovenski standard je istoveten z: prEN 15012
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
23.040.45 Fitingi iz polimernih Plastics fittings
materialov
91.140.80 Drenažni sistemi Drainage systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
DRAFT
prEN 15012
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2011
ICS 91.140.80 Will supersede EN 15012:2007
English Version
Plastics piping systems - Non pressure soil and waste discharge
piping components within the building structure - Requirements
and test/assessment methods for pipes and fittings
Systèmes de canalisations en plastique - Composants de Kunststoff-Rohrleitungssysteme - Drucklose
canalisations pour l'évacuation des eaux-vannes et des Rohrleitungssysteme zum Ableiten von Abwasser innerhalb
eaux usées à l'intérieur de la structure des bâtiments - der Gebäudestruktur - Anforderungen und Prüf-
Exigences et méthodes d'essai/d'évaluation pour tubes et /Bewertungsverfahren für Rohre und Formstücke
raccords
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 155.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 15012:2011: E
worldwide for CEN national Members.

prEN 15012:2011 (E)
Contents Page
Foreword . 3
Introduction . 3
1 Scope . 4
2 Normative references . 4
3 Terms, definitions and symbols . 5
4 Requirements . 6
4.1 Reaction to fire . 6
4.2 Maximum load for admissible deformation for pipes and fittings for applications buried in
ground within the building structure . 6
4.3 Dimensional tolerances . 6
4.4 Tightness . 8
4.5 Durability . 8
4.6 Release of dangerous substances . 8
5 Test methods . 8
5.1 Reaction to fire of pipes and fittings . 8
5.2 Maximum load for admissible deformation . 8
5.3 Dimensional tolerances . 9
5.4 Tightness . 9
5.5 Durability . 9
6 Evaluation of conformity . 10
6.1 General . 10
6.2 Initial type testing – Type testing . 10
6.3 Factory production control (FPC) . 13
Annex A (informative) Product standards for soil and waste discharge piping systems in plastics
materials . 19
Annex B (informative) Standards for assessment of conformity for soil and waste discharge
piping systems in plastics materials . 20
Annex ZA (informative) Clauses of this European Standard addressing the provisions of EU
Construction Products Directive . 21
ZA.1. Scope and relevant characteristics . 21
ZA.2. Procedure for attestation of conformity of plastics pipes and fittings . 23
ZA.2.1. System of attestation of conformity . 23
ZA.2.2. EC Certificate and Declaration of conformity . 25
ZA.3. CE marking and labelling . 26
ZA.3.1. CE marking requirements . 26
Bibliography . 30

prEN 15012:2011 (E)
Foreword
This document (prEN 15012:2011) has been prepared by Technical Committee CEN/TC 155 “Plastics piping
systems and ducting systems”, the secretariat of which is held by NEN.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under Mandate M/131 "Pipes, tanks and ancillaries not in contact with
water intended for human consumption" given to CEN by the European Commission and the European Free
Trade Association and supports essential requirements of EU Directives.
For the relationship with EU Directives, see informative Annex ZA, which is an integral part of this document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech,
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and United Kingdom.
Introduction
This European Standard specifies only those characteristics of pipes and fittings for soil and waste
applications inside buildings or buried in ground within the building structure, that need to be known to
determine if the works in which these are to be installed can satisfy the essential requirements of the EU
Directive(s). Additional characteristics are specified in the documents listed in Annex A or in other appropriate
product specifications.
prEN 15012:2011 (E)
1 Scope
This European Standard specifies requirements for non-pressure plastics pipes and fittings for soil and waste
applications.
It is intended to be used in soil and waste discharge applications:
 inside the building (application area code "B"),
 buried in ground within the building structure (application area code "BD") and with a diameter greater
than or equal to 75 mm
It gives the associated test/assessment methods.
This standard does not cover adhesives, joint sealings and gaskets
NOTE For this standard, the term fitting includes the term joint as meant by mandate M131.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
EN 681-1, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage
applications — Part 1: Vulcanised rubber
EN 681-2, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage
applications — Part 2: Thermoplastic elastomers
EN 681-3, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage
applications — Part 3: Cellular materials of vulcanised rubber
EN 681-4, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage
applications — Part 4: Cast polyurethane sealing elements
EN 727, Plastics piping and ducting systems — Thermoplastics pipes and fittings — Determination of vicat
softening temperature (VST)
EN 728, Plastics piping and ducting systems — Polyolefin pipes and fittings — Determination of oxidation
induction time
EN 1053, Plastics piping systems — Thermoplastics piping systems for non-pressure applications — Test
method for watertightness
EN 1054, Plastics piping systems — Thermoplastics piping systems for soil and waste discharge — Test
method for airtightness of joints
EN 1055, Plastics piping systems — Thermoplastics piping systems for soil and waste discharge inside
buildings — Test method for resistance to elevated temperature cycling
EN 1329-1, Plastics piping systems for soil and waste discharge (low and high temperature) within the
building structure — Unplasticized poly(vinyl chloride) (PVC-U) — Part 1: Specifications for pipes, fittings and
the system
EN 1451-1, Plastics piping systems for soil and waste discharge (low and high temperature) within the
building structure — Polypropylene (PP) — Part 1: Specifications for pipes, fittings and the system
prEN 15012:2011 (E)
EN 1455-1, Plastics piping systems for soil and waste discharge (low and high temperature) within the
building structure — Acrylonitrile-butadiene-styrene (ABS) — Part 1: Requirements for pipes, fittings and the
system
EN 1519-1, Plastics piping systems for soil and waste discharge (low and high temperature) within the
building structure — Polyethylene (PE) — Part 1: Specifications for pipes, fittings and the system
EN 1565-1, Plastics piping systems for soil and waste discharge (low and high temperature) within the
building structure — Styrene copolymer blends (SAN+PVC) — Part 1: Specifications for pipes, fittings and the
system
EN 1566-1, Plastics piping systems for soil and waste discharge (low and high temperature) within the
building structure — Chlorinated poly(vinyl chloride) (PVC-C) — Part 1: Specifications for pipes, fittings and
the system
EN 13501-1, Fire classification of construction products and building elements — Part 1: Classification using
test data from reaction to fire tests
EN 13823, Reaction to fire tests for building products — Building products excluding floorings exposed to the
thermal attack by a single burning item
EN 16000, Plastics piping systems — Systems within the building structure — Mounting and fixing of
components in the test apparatus to therma
...