FprEN ISO 19085-15
(Main)Woodworking machines - Safety - Part 15: Presses (ISO/FDIS 19085-15:2024)
Woodworking machines - Safety - Part 15: Presses (ISO/FDIS 19085-15:2024)
1.1 This document specifies the safety requirements and measures for
— cold presses,
— hot presses,
— bending presses,
— edge/face gluing presses,
— membrane presses, and
— embossing presses,
where the pressing force is applied by hydraulic, pneumatic or electrical actuators pushing two flat or shaped surfaces against each other, capable of continuous production use, altogether referred to as “machines”.
This document deals with all significant hazards, hazardous situations and events as listed in Annex A, relevant to machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer, including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases are taken into account.
1.2 This document is applicable to machines fitted with one or more of the following devices or additional working units, whose hazards have been dealt with:
a) a device for hot gluing;
b) a device for high-frequency gluing in the frequency range from 1 MHz to 400 MHz;
c) a device for high-frequency shaping in the frequency range from 1 MHz to 400 MHz;
d) an automatic workpiece loading and unloading system;
e) an intermediate additional platen;
f) a workpiece extractor;
g) a horizontal pressing system;
h) split moveable platens.
1.3 The machines are designed to process workpieces consisting of:
a) solid wood;
b) materials with similar characteristics to wood (see ISO 19085-1:2021, 3.2), except those with light alloy laminates/edges/profiles for high-frequency presses;
c) wood-based material such as chipboard, fibreboard and plywood composed/laminated with steel sheets/edges/profiles, except for high-frequency presses;
d) honeycomb board;
e) composite boards made from the materials listed above.
1.4 This document does not deal with any hazards related to:
— specific devices that differ from the list above;
— hot fluid heating systems internal to the machine other than electrical;
— any hot fluid heating systems external to the machine;
— operation of taking intermediate platens out and in again;
— the combination of a single machine being used with any other machine (as part of a line).
1.5 This document is not applicable to:
— frame presses;
— membrane presses where the pressing force is applied by vacuum only;
— presses for producing chipboard, fibreboard, OSB;
— machines intended for use in potentially explosive atmosphere;
— machines manufactured before the date of publication of this document.
Holzbearbeitungsmaschinen - Sicherheit - Teil 15: Pressen (ISO/FDIS 19085 15:2024)
Dieses Dokument stellt Sicherheitsanforderungen und Maßnahmen zur Verfügung für stationäre
— Kaltpressen;
— Heißpressen;
— Biegepressen;
— Kanten-/Flächenverleimpressen;
— Membranpressen;
— Prägepressen;
mit Handbeschickung und Handentnahme, bei denen die Presskraft durch hydraulische Antriebe aufgebracht wird, die zwei ebene oder geformte Flächen gegeneinander drücken, nachfolgend als „Maschinen“ bezeichnet.
Es behandelt alle im Abschnitt 4 aufgeführten signifikanten Gefährdungen, Gefährdungssituationen und Gefährdungsereignisse, die auf die Maschinen zutreffen, wenn sie bestimmungsgemäß und entsprechend den vom Hersteller vorhergesehenen Bedingungen verwendet, eingestellt und gewartet werden, einschließlich der vernünftigerweise vorhersehbaren Fehlanwendung. Ferner werden die Phasen Transport, Montage, Demontage, Rückbau und Verschrottung berücksichtigt.
ANMERKUNG Hinsichtlich zutreffender aber nicht signifikanter Gefährdungen, z. B. scharfe Kanten des Maschinengestells, siehe ISO 12100:2010.
Es gilt auch für Maschinen, die mit einer oder mehreren der folgenden Einrichtungen/zusätzlichen Arbeitsaggregate ausgerüstet sind, deren Gefährdungen behandelt wurden:
a) Einrichtung zum Heißverleimen;
b) Einrichtung zum Hochfrequenzverleimen;
c) Einrichtung zum Hochfrequenzformen;
d) automatisches Be- und Entladesystem für Werkstücke;
e) zusätzliche Zwischenplatten;
f) Werkstück-Auszieher;
g) Werkstück-Spanndruckbalken;
h) geteilte bewegliche Platten.
Die Maschinen sind gestaltet für die Bearbeitung von Werkstücken aus:
1) Massivholz;
2) Werkstoffen mit ähnlichen Eigenschaften wie Holz (siehe ISO 19085-1:2017, 3.2);
3) Wabenplatten.
Dieses Dokument behandelt keine Gefährdungen im Zusammenhang mit:
— spezifischen Einrichtungen, die von der obigen Liste abweichen;
— Heizsystemen für heiße Flüssigkeiten innerhalb der Maschine, die nicht elektrisch betrieben werden;
— Heizsystemen für heiße Flüssigkeiten außerhalb der Maschine;
— dem Vorgang der Entnahme und des Wiedereinsetzens von Zwischenplatten;
— der Kombination einer einzelnen Maschine, die mit einer beliebigen anderen Maschine (als Teil einer Linie) verwendet wird.
Es gilt nicht für:
— Rahmenpressen;
— Membranpressen, bei denen die Presskraft nur durch Vakuum aufgebracht wird;
— Pressen zur Herstellung von Spanplatten, Faserplatten, OSB;
— Maschinen, die zur bestimmungsgemäßen Verwendung in potentiell explosiven Atmosphären vorgesehen sind;
— Maschinen, die vor dem Datum seiner Veröffentlichung als Internationale Norm hergestellt wurden.
Machines à bois - Sécurité - Partie 15: Presses (ISO/FDIS 19085-15:2024)
1.1 Le présent document spécifie les exigences et mesures de sécurité pour:
— les presses à froid,
— les presses à chaud,
— les presses à cintrer,
— les presses de collage sur chant/face,
— les presses à membrane,
— les presses à estamper,
dans lesquelles la force de pressage est appliquée par des actionneurs hydrauliques, pneumatiques ou électriques poussant deux surfaces planes ou façonnées l’une contre l’autre, capables d’une utilisation en production continue, ci-après également désignées «machines».
Le présent document traite de tous les phénomènes dangereux, situations et événements dangereux significatifs, tels qu'énumérés à l'Annexe A, applicables aux machines lorsqu'elles sont utilisées, réglées et entretenues comme prévu et dans les conditions prévues par le fabricant, incluant une mauvaise utilisation raisonnablement prévisible. Les phases de transport, d'assemblage, de démontage, de mise hors service et de mise au rebut sont également prises en compte.
1.2 Le présent document est applicable aux machines équipées d'un ou plusieurs des dispositifs/unités de travail supplémentaires suivants, dont les phénomènes dangereux ont été traités:
a) dispositif de collage à chaud;
b) dispositif de collage à haute fréquence dans la gamme de fréquences de 1 MHz à 400 MHz;
c) dispositif de façonnage à haute fréquence dans la gamme de fréquences de 1 MHz à 400 MHz;
d) système de chargement et déchargement automatiques de la pièce;
e) plateaux intermédiaires supplémentaires;
f) extracteur de pièce;
g) système de pressage horizontal;
h) plateaux mobiles séparés.
1.3 Les machines sont conçues pour usiner des pièces constituées de:
a) bois massif;
b) matériau présentant des caractéristiques similaires à celles du bois (voir l'ISO 19085-1:2021, 3.2) à l’exception de ceux qui comportent des laminés/chants/profilés en alliage léger pour les presses à haute fréquence;
c) matériaux à base de bois tels que les panneaux d’aggloméré, panneaux de fibres et contreplaqués composés de/laminés avec des tôles/chants/profilés en acier, à l’exception des presses à haute fréquence;
d) plaque alvéolaire;
e) plaques composites fabriquées à partir des matériaux énumérés ci-dessus.
1.4 Le présent document ne traite pas des phénomènes dangereux relatifs à:
— des dispositifs spécifiques qui diffèrent de la liste ci-dessus;
— des systèmes de chauffage par fluide chaud internes à la machine, autres qu’électriques;
— tous les systèmes de chauffage par fluide chaud externe à la machine;
— l’opération d’extraction et de réinsertion des plateaux intermédiaires;
— la combinaison d’une machine simple utilisée avec toute autre machine (comme une partie d’une ligne).
1.5 Le présent document ne s’applique pas aux:
— presses à cadre;
— presses à membrane dans lesquelles la force de pressage est appliquée uniquement par dépression;
— presses pour la production de panneaux de particules, de panneaux de fibres, d’OSB;
— machines prévues pour une utilisation en atmosphère explosible;
— machines fabriquées avant la date de publication du présent document.
Lesnoobdelovalni stroji - Varnost - 15. del: Stiskalnice (ISO/FDIS 19085 15:2024)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN ISO 19085-15:2023
01-februar-2023
Lesnoobdelovalni stroji - Varnost - 15. del: Stiskalnice (ISO/DIS 19085-15:2022)
Woodworking machines - Safety - Part 15: Presses (ISO/DIS 19085-15:2022)
Holzbearbeitungsmaschinen - Sicherheit - Teil 15: Pressen (ISO/DIS 19085 15:2022)
Machines à bois Sécurité Partie 15: Presses (ISO/DIS 19085-15:2022)
Ta slovenski standard je istoveten z: prEN ISO 19085-15
ICS:
13.110 Varnost strojev Safety of machinery
25.120.10 Kovaški stroji. Stiskalnice. Forging equipment. Presses.
Škarje Shears
79.120.10 Lesnoobdelovalni stroji Woodworking machines
oSIST prEN ISO 19085-15:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
oSIST prEN ISO 19085-15:2023
oSIST prEN ISO 19085-15:2023
DRAFT INTERNATIONAL STANDARD
ISO/DIS 19085-15
ISO/TC 39/SC 4 Secretariat: UNI
Voting begins on: Voting terminates on:
2022-11-23 2023-02-15
Woodworking machines — Safety —
Part 15:
Presses
Machines à bois — Sécurité —
Partie 15: Presses
ICS: 13.110; 79.120.10
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 19085-15:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2022
oSIST prEN ISO 19085-15:2023
ISO/DIS 19085-15:2022(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 19085-15
ISO/TC 39/SC 4 Secretariat: UNI
Voting begins on: Voting terminates on:
Woodworking machines — Safety —
Part 15:
Presses
Machines à bois — Sécurité —
Partie 15: Presses
ICS: 13.110; 79.120.10
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2022
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: +41 22 749 01 11
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: copyright@iso.org
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 19085-15:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2022
oSIST prEN ISO 19085-15:2023
ISO/DIS 19085-15:2022(E)
Contents Page
Foreword .v
Introduction . vi
1 Scope . 1
2 Normative references . 2
3 Terms and definitions . 2
4 Safety requirements and measures for controls .12
4.1 Safety and reliability of control systems.12
4.2 Control devices .12
4.3 Start . 13
4.3.1 Direct start .13
4.3.2 Start via control power-on . 13
4.4 Safe stops . 13
4.4.1 General .13
4.4.2 Normal stop .13
4.4.3 Operational stop . 14
4.4.4 Emergency stop . 14
4.5 Braking function of tools . 14
4.6 Mode selection . 14
4.7 Tool speed changing . 14
4.7.1 Speed changing by shifting the belts on the pulleys . 14
4.7.2 Speed changing by incremental speed change motor . 14
4.7.3 Infinitely variable speed by frequency inverter . 14
4.8 Failure of any power supply . 14
4.9 Manual reset control . 15
4.10 Standstill detection and monitoring . 15
4.11 Machine moving parts speed monitoring. 15
4.12 Time delay. 15
4.13 Teleservice . 15
5 Safety requirements and measures for protection against mechanical hazards .15
5.1 Stability . 15
5.2 Risk of break-up during operation . 16
5.3 Tool holder and tool design . 16
5.3.1 General . 16
5.3.2 Spindle locking . 16
5.3.3 Circular saw blade fixing devices . 16
5.3.4 Flange dimensions for circular saw blades . 16
5.4 Braking . 16
5.4.1 Braking of tool spindles . 16
5.4.2 Maximum run-down time . 16
5.4.3 Brake release . 16
5.5 Safeguards . 17
5.5.1 Fixed guards . 17
5.5.2 Interlocking moveable guards . 17
5.5.3 Hold-to-run control . 17
5.5.4 Two hand control . 17
5.5.5 Electro-sensitive protective equipment (ESPE) . 17
5.5.6 Pressure sensitive protective equipment (PSPE) . 17
5.5.7 Enabling control . 17
5.6 Prevention of access to hazardous moving parts . 17
5.6.1 Guarding of racks . 17
5.6.2 Safeguarding machines with manual loading and unloading . 18
5.6.3 Safeguarding machines with high-frequency system . 19
iii
oSIST prEN ISO 19085-15:2023
ISO/DIS 19085-15:2022(E)
5.6.4 Safeguarding machines with automatic workpiece loading/unloading
systems type 1, type 2 and type 3 . 20
5.6.5 Safeguarding machines with automatic workpiece loading/unloading
system type 4 . 20
5.6.6 Safeguarding machines with automatic workpiece loading/unloading
system type 5 . 21
5.6.7 Safeguarding machines with automatic workpiece loading/unloading
system type 6 . 21
5.7 Impact hazard . 22
5.8 Clamping devices .23
5.9 Measures against ejection .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.