prEN 896
(Main)Chemicals used for treatment of water intended for human consumption - Sodium hydroxide
Chemicals used for treatment of water intended for human consumption - Sodium hydroxide
This document is applicable to sodium hydroxide used for treatment of water intended for human consumption. It describes the characteristics and specifies the requirements and the corresponding test methods for sodium hydroxide. It gives information on its use in water treatment.
Produkte zur Aufbereitung von Wasser für den menschlichen Gebrauch - Natriumhydroxid
Dieses Dokument gilt für Natriumhydroxid zur Aufbereitung von Wasser für den menschlichen Gebrauch. Es beschreibt die Eigenschaften von Natriumhydroxid und legt die Anforderungen sowie die entsprechenden Prüfverfahren für Natriumhydroxid fest. Es enthält Angaben zu dessen Anwendung in der Wasseraufbereitung.
Produits chimiques utilisés pour le traitement de l’eau destinée à la consommation humaine - Hydroxyde de sodium
Le présent document s’applique à l’hydroxyde de sodium utilisé pour le traitement de l’eau destinée à la consommation humaine. Il décrit les caractéristiques de l’hydroxyde de sodium et spécifie les exigences et les méthodes d’essai correspondantes. Il donne des informations sur son emploi dans le traitement de l’eau.
Kemikalije, ki se uporabljajo za pripravo pitne vode - Natrijev hidroksid
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2020
Kemikalije, ki se uporabljajo za pripravo pitne vode - Natrijev hidroksid
Chemicals used for treatment of water intended for human consumption - Sodium
hydroxide
Produkte zur Aufbereitung von Wasser für den menschlichen Gebrauch -
Natriumhydroxid
Produits chimiques utilisés pour le traitement de l’eau destinée à la consommation
humaine - Hydroxyde de sodium
Ta slovenski standard je istoveten z: prEN 896
ICS:
13.060.20 Pitna voda Drinking water
71.100.80 Kemikalije za čiščenje vode Chemicals for purification of
water
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2020
ICS 71.100.80 Will supersede EN 896:2012
English Version
Chemicals used for treatment of water intended for human
consumption - Sodium hydroxide
Produits chimiques utilisés pour le traitement de l'eau Produkte zur Aufbereitung von Wasser für den
destinée à la consommation humaine - Hydroxyde de menschlichen Gebrauch - Natriumhydroxid
sodium
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 164.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 896:2020 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Description . 4
4.1 Identification . 4
4.2 Commercial forms . 5
4.3 Physical properties . 5
4.4 Chemical properties . 7
5 Purity criteria . 7
5.1 General . 7
5.2 Composition of commercial product . 8
5.3 Impurities and main by-products . 8
5.4 Chemical parameters . 8
6 Test methods . 9
6.1 Sampling . 9
6.2 Analyses . 9
7 Labelling – Transportation – Storage . 10
7.1 Means of delivery . 10
)
7.2 Labelling according to the EU legislation . 10
7.3 Transportation regulations and labelling . 11
7.4 Marking . 11
7.5 Storage . 12
Annex A (informative) General information on sodium hydroxide . 13
Annex B (normative) Analytical methods . 14
Annex C (normative) General rules relating to safety . 23
Bibliography . 24
European foreword
This document (prEN 896:2020) has been prepared by Technical Committee CEN/TC 164 “Water supply”,
the secretariat of which is held by AFNOR.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 896:2012.
In comparison with the previous edition, the following technical modifications have been made:
a) Modification of 7.3 on transportation regulations and labelling, adding the sentence “The user must be
aware of the incompatibilities between transported products.”;
b) Modification of 7.4 on marking. The requirements of marking are also applied to the accompanying
documents.
1 Scope
This document is applicable to sodium hydroxide used for treatment of water intended for human
consumption. It describes the characteristics and specifies the requirements and the corresponding test
methods for sodium hydroxide. It gives information on its use in water treatment.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
EN ISO 3696, Water for analytical laboratory use — Specification and test methods (ISO 3696)
EN ISO 12846:2012, Water quality — Determination of mercury — Method using atomic absorption
spectrometry (AAS) with and without enrichment (ISO 12846:2012)
ISO 979, Sodium hydroxide for industrial use — Method of assay
ISO 3165, Sampling of chemical products for industrial use — Safety in sampling
ISO 3196, Sodium hydroxide for industrial use — Determination of carbonates content — Titrimetric method
ISO 6206, Chemical products for industrial use — Sampling — Vocabulary
ISO 8213, Chemical products for industrial use — Sampling techniques — Solid chemical products in the form
of particles varying from powders to coarse lumps
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp
— IEC Electropedia: available at https://www.electropedia.org/
4 Description
4.1 Identification
4.1.1 Chemical name
Sodium hydroxide.
4.1.2 Synonym or common name
Caustic soda.
4.1.3 Relative molecular mass
40,0.
4.1.4 Empirical formula
NaOH.
4.1.5 Chemical formula
NaOH.
1)
4.1.6 CAS Registry Number
1310-73-2.
2)
4.1.7 EINECS reference
215-185-5.
4.2 Commercial forms
The product is available as flakes, pearls, solid, or as an aqueous solution of different concentrations. For safe
handling and use and emergency procedures of sodium permanganate, refer to Annex C.
4.3 Physical properties
4.3.1 Appearance
Solid: the product is white, deliquescent.
Liquid: the product is a clear solution, slightly turbid colourless solution, slightly viscous.
4.3.2 Density
Solid : the density of this product is 2,1 g/cm .
The bulk density of pearls is 1,2 kg/dm .
Liquid : the density of solution is 1,52 g/ml for a product concentration of mass fraction of 50 % at 20 °C.
4.3.3 Solubility in water
The product is highly soluble at all temperatures above 20 °C (partial crystallization occurs above
concentration of mass fraction of 55 %, (see Figure 1).
1)
Chemical Abstracts Service Registry Number.
2)
European Inventory of Existing Commercial Chemical Substances.
Key
1 temperature in °C
2 NaOH concentration in mass fraction in %
Figure 1 — Solubility of sodium hydroxide
4.3.4 Vapour pressure
Solution of concentration of mass fraction of 50 %
— 120 Pa at 20 °C;
— 450 Pa at 40 °C;
— 5 000 Pa at 80 °C.
3)
4.3.5 Boiling point at 100 kPa
145 °C for a solution of concentration of mass fraction of 50 %.
4.3.6 Crystallization point
+ 12 °C for a solution of concentration of mass fraction of 50 % (see Figure 1).
3)
100 kPa = 1 bar.
4.3.7 Specific heat
3 220 J/(kg K) at 20 °C for a solution of concentration of mass fraction of 50 %.
4.3.8 Viscosity (dynamic)
For a solution of concentration of mass fraction of 50 %:
— 100 Pa.s at 20 °C;
— 25 Pa.s at 40 °C;
— 5 Pa.s at 80 °C.
4.3.9 Critical temperature
Not applicable.
4.3.10 Critical pressure
Not applicable.
4.3.11 Physical hardness
Not applicable.
4.4 Chemical properties
The solutions of sodium hydroxide are strongly alkaline.
Dilution of sodium hydroxide is very exothermic. For additional information on sodium hydroxide see
Annex A.
5 Purity criteria
5.1 General
This document specifies the minimum purity requirements for sodium hydroxide used for the treatment of
water intended for human consumption. Limits are given for impurities commonly present in the product.
Depending on the raw material and the manufacturing process other impurities may be present and, if so,
this shall be notified to the user and when necessary to relevant authorities.
The national regulations allow to users to clarify whether the product is of appropriate purity for the
treatment of water intended for human consumption, taking into account raw water quality, required
dosage, contents of other impurities and additives used in the product and not stated in this product
standard.
Limits have been given for impurities and chemical parameters where these are likely to be present in
significant quantities from the current production process and raw materials. If the production process or
raw materials leads to significant quantities of impurities, by-products or additives being present, this shall
be notified to the user.
5.2 Composition of commercial product
The product shall contain not less than a mass fraction of 96 % of NaOH for the solid form. Typical
concentration for solutions of sodium hydroxide is either a mass fraction of 50 % or 30 % , and shall be in
any case within the manufacturer’s stated tolerance.
5.3 Impurities and main by-products
The product shall conform to the requirements specified in Table 1.
The concentration limits refer to pure NaOH mass fraction of 100 %.
Table 1 — Impurities
Impurity Limit
in mass fraction in
% of NaOH
a max. 2,4
Sodium chloride (NaCl)
b
max. 0,4
Sodium carbonate (Na CO )
2 3
c
max. 0,7
Sodium chlorate (NaClO )
a
Too high concentrations can cause problems with some ion exchange resins.
b
Sodium carbonate is formed in contact with atmospheric carbon dioxide.
c
The presence of any oxidizing agent in sodium hydroxide is to be avoided.
5.4 Chemical parameters
The product shall conform to the requirements specified in Table 2.
Tabl
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.