iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 1474-1:2008

(Main)

Installation and equipment for liquefied natural gas - Design and testing of marine transfer systems - Part 1: Design and testing of transfer arms

Installation and equipment for liquefied natural gas - Design and testing of marine transfer systems - Part 1: Design and testing of transfer arms

This European Standard specifies the design, minimum safety requirements and inspection and testing procedures for liquefied natural gas (LNG) transfer arms intended for use on conventional onshore (LNG) terminals  ). It also covers the minimum requirements for safe LNG transfer between ship and shore.
Although the requirements for remote control power systems are covered, the standard does not include all the details for the design and fabrication of standard parts and fittings associated with transfer arms.
The content of this European Standard is supplementary to local or national standards and regulations and is additional to the requirements of EN 1532 and EN 1473.

Anlagen und Ausrüstung für Flüssigerdgas - Auslegung und Prüfung von Schiffsübergabesystemen - Teil 1: Auslegung und Prüfung von Verladearmen

Diese Europäische Norm legt die Auslegung, die minimalen Sicherheitsanforderungen und die Kontroll- und Prüfverfahren für Verladearme für Flüssigerdgas (LNG, en: liquefied natural gas) fest, die zum Gebrauch auf konventionellen landgebundenen (LNG) Verladestationen dienen ). Diese Norm enthält auch die Mindestanforderungen für sicheren Umschlag von Flüssigerdgas zwischen Schiff und Landanlage.
Obgleich die Anforderungen für Fernbedienungssysteme aufgeführt sind, gibt das Dokument nicht alle Einzelheiten für die Auslegung und Herstellung von genormten Teilen und Armaturen für Ladearme an.
Der Inhalt des Dokuments gilt zusätzlich zu örtlichen oder nationalen Normen und Vorschriften. Er ergänzt die Anforderungen von EN 1532 und EN 1473.

Installations et équipements relatifs au gaz naturel liquéfié - Conception et essais des systèmes de transfert marins - Partie 1: Conception et essais des bras de chargement/déchargement

Cette Norme Européenne spécifie les règles de conception, les prescriptions minimales de sécurité ainsi que
les procédures de contrôle et d'essais relatifs aux bras de chargement/déchargement de gaz naturel liquéfié
(GNL) destinés à être utilisés sur des terminaux terrestres conventionnels1). Elle fixe également les
prescriptions minimales permettant de garantir que le transfert de GNL entre le navire et le terminal s'effectue
en toute sécurité.
Bien que la présente norme s'applique aux systèmes de télécommande, elle ne fixe pas tous les détails
relatifs à la conception et à la fabrication des pièces normalisées et des raccords des bras de
chargement/déchargement.
Le contenu de cette Norme Européenne vient compléter les normes et règlements locaux ou nationaux, et
s'ajoutent aux dispositions des normes EN 1532 et EN 1473.

Napeljave in oprema za utekočinjeni zemeljski plin - Načrtovanje in preskušanje obalnih pretakališč - 1. del: Načrtovanje in preskušanje rok za pretakanje

General Information

Status
Withdrawn
Publication Date
02-Dec-2008
Withdrawal Date
15-Mar-2016
ICS
75.200 - Petroleum products and natural gas handling equipment
Technical Committee
CEN/TC 282 - Installation and equipment for LNG
Drafting Committee
CEN/TC 282 - Installation and equipment for LNG
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
16-Mar-2016
Ref Project
SIST EN 1474-1:2009 - Installation and equipment for liquefied natural gas - Design and testing of marine transfer systems - Part 1: Design and testing of transfer arms

Relations

Replaces
EN 1474:1997 - Installation and equipment for liquefied natural gas - Design and testing of loading/unloading arms
Effective Date
22-Dec-2008
Replaced By
EN ISO 16904:2016 - Petroleum and natural gas industries - Design and testing of LNG marine transfer arms for conventional onshore terminals (ISO 16904:2016)
Effective Date
08-Jun-2022

Buy Standard

EN 1474-1:2009EN 1474-1:2009
PreviousNext
Standard
EN 1474-1:2009
English language
74 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.UHWDNDQMHAnlagen und Ausrüstung für Flüssigerdgas - Auslegung und Prüfung von Schiffsübergabesystemen - Teil 1: Auslegung und Prüfung von VerladearmenInstallations et équipements relatifs au gaz naturel liquéfié - Conception et essais des systemes de transfert marins - Partie 1: Conception et essais des bras de chargement/déchargementInstallation and equipment for liquefied natural gas - Design and testing of marine transfer systems - Part 1: Design and testing of transfer arms75.200Petroleum products and natural gas handling equipmentICS:Ta slovenski standard je istoveten z:EN 1474-1:2008SIST EN 1474-1:2009en,fr,de01-marec-2009SIST EN 1474-1:2009SLOVENSKI
STANDARDSIST EN 1474:19991DGRPHãþD



SIST EN 1474-1:2009



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1474-1December 2008ICS 75.200Supersedes EN 1474:1997
English VersionInstallation and equipment for liquefied natural gas - Design andtesting of marine transfer systems - Part 1: Design and testing oftransfer armsInstallations et équipements relatifs au gaz naturel liquéfié -Conception et essais des systèmes de transfert marins -Partie 1: Conception et essais des bras dechargement/déchargementAnlagen und Ausrüstung für Flüssigerdgas - Auslegung undPrüfung von Schiffsübergabesystemen - Teil 1: Auslegungund Prüfung von VerladearmenThis European Standard was approved by CEN on 1 November 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1474-1:2008: ESIST EN 1474-1:2009



EN 1474-1:2008 (E) 2 Contents Page Foreword .4 1 Scope .5 2 Normative references .5 3 Terms, definitions and abbreviations .7 4 Design of the arms. 15 4.1 Definition of the length and the configuration of the arms, arms description . 15 4.1.1 General . 15 4.1.2 Balancing . 16 4.1.3 Arms dimensions and clearances. 16 4.2 Design basis . 16 4.2.1 Product line diameter and product data . 16 4.2.2 Material and grades . 17 4.3 Swivel joints . 21 4.3.1 General . 21 4.3.2 Product sealing arrangement .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 1474-2:2020/AC:2023(Corrigendum)
Installation and equipment for liquefied natural gas - Design and testing of marine transfer systems - Part 2: Design and testing of transfer hoses
SIST EN 1474-2:2020/AC:2023

This European Standard gives general guidelines for the design, material selection, qualification, certification, and testing details for Liquefied Natural Gas (LNG) transfer hoses for offshore transfer or on coastal weather-exposed facilities for aerial, floating and submerged configurations or a combination of these. Whilst this European Standard is applicable to all LNG hoses, it is acknowledged that there may be further specific requirements for floating and submerged hoses.
The transfer hoses will be designed to be part of transfer systems (it means that they will be fitted with ERS, QCDC, handling systems, hydraulic and electric components etc.) To avoid unnecessary repetition, cross-references to EN 1474-1 and EN 1474-3, are made for all compatible items, and for references, definitions and abbreviations. Where additional references, definitions and abbreviations are required specifically for LNG hoses, they are listed in this European Standard.
Transfer hoses need to be durable when operating in the marine environment and to be flexible with a minimum bending radius compatible with handling and the operating requirements of the transfer system.

  • Corrigendum
    2 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 20257-2:2021(Main)
Installation and equipment for liquefied natural gas - Design of floating LNG installations - Part 2: Specific FSRU issues (ISO 20257-2:2021)
SIST EN ISO 20257-2:2021

This document provides specific requirements and guidance for the design and operation of floating LNG storage and regasification units (FSRU) described in ISO 20257-1.
This document is applicable to offshore, near-shore or docked FSRUs and to both new-built and converted FSRUs.
This document includes requirements to the jetty when an FSRU is moored to a jetty.

  • Standard
    49 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1473:2021(Main)
Installation and equipment for liquefied natural gas - Design of onshore installations
SIST EN 1473:2021

This document gives guidelines for the design, construction and operation of all onshore liquefied natural gas (LNG) installations for the liquefaction, storage, vaporization, transfer and handling of LNG and natural gas (NG).
This document is applicable for plants with an LNG storage capacity above 200 t.
The designated boundary limits are LNG inlet/outlet by the ship’s manifold including vapour return connection, the truck loading/unloading connection including vapour return, the rail car loading/unloading connection including vapour return and the natural gas in and outlet boundary by piping systems.
Terminals or plant types have one or more boundary limits as described in this scope (see Figure 1).
A short description of each of these installations is given in Annex G.
Feed gas for LNG liquefaction installations (plant) can be from gas field, associated gas from oil field, piped gas from transportation grid or from renewables.
Floating solutions (for example FPSO, FSRU, SRV), whether off-shore or near-shore, are not covered by this document even if some concepts, principles or recommendations could be applied. However, in case of berthed FSRU with LNG transfer across the jetty, the following recommendations apply for the jetty and topside facilities.
In case of solutions using floating storage unit (FSU) and land-based re-gasification solution, the on-shore part is covered by these standard recommendations.
Plants with a storage inventory from 5 t up to 200 t are covered by [5].

  • Standard
    139 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1474-2:2020(Main)
Installation and equipment for liquefied natural gas - Design and testing of marine transfer systems - Part 2: Design and testing of transfer hoses
SIST EN 1474-2:2020

This European Standard gives general guidelines for the design, material selection, qualification, certification, and testing details for Liquefied Natural Gas (LNG) transfer hoses for offshore transfer or on coastal weather-exposed facilities for aerial, floating and submerged configurations or a combination of these. Whilst this European Standard is applicable to all LNG hoses, it is acknowledged that there may be further specific requirements for floating and submerged hoses.
The transfer hoses will be designed to be part of transfer systems (it means that they will be fitted with ERS, QCDC, handling systems, hydraulic and electric components etc.) To avoid unnecessary repetition, cross-references to EN 1474-1 and EN 1474-3, are made for all compatible items, and for references, definitions and abbreviations. Where additional references, definitions and abbreviations are required specifically for LNG hoses, they are listed in this European Standard.
Transfer hoses need to be durable when operating in the marine environment and to be flexible with a minimum bending radius compatible with handling and the operating requirements of the transfer system.

  • Standard
    64 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 20257-1:2020(Main)
Installation and equipment for liquefied natural gas - Design of floating LNG installations - Part 1: General requirements (ISO 20257-1:2020, Corrected version 2020-10)
SIST EN ISO 20257-1:2020

This document provides requirements and guidance for the design and operation of floating liquefied natural gas (LNG) installations, including installations for the liquefaction, storage, vaporisation, transfer and handling of LNG, in order to have a safe and environmentally acceptable design and operation of floating LNG installations.
This document is applicable to:
—     floating LNG liquefaction installations (plant) — FLNG;
—     floating LNG regasification installations (plant) — FSRU;
—     floating storage units — FSU.
This document is applicable to offshore, near-shore or docked floating LNG installations.
This document includes any jetty in the scope in case of docked floating LNG installations with regards to the mooring. This document briefly describes floating LNG mooring concepts.
This document is applicable to both newbuilt and converted floating LNG installations, and addresses specific requirements.
This document is not applicable to:
—     onshore LNG storage, liquefaction and/or regasification installations/plants, except for docked FSRU and/or FLNG installations;
—     offshore LNG plants based on non-floating structure (such as gravity based structure [GBS] principle); and
—     support onshore based facilities (such as support vessels, tugs, etc.).
This document is not intended for design floating power generation facilities though relevant parts of this document can be used.
This document is not intended to cover LNG as fuel bunkering applications.

  • Standard
    164 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 20088-2:2020(Main)
Determination of the resistance to cryogenic spill of insulation materials - Part 2: Vapour exposure (ISO 20088-2:2020)
SIST EN ISO 20088-2:2020

This document describes a method for determining the resistance of Cryogenic Spill Protection (CSP) systems to vapour generated from a cryogenic liquid release where the liquid content is practically zero. It is applicable where CSP systems are installed on carbon steel.
The test provided in this document is not applicable to high pressure cryogenic liquid releases that can be found in refrigeration circuits and in LNG streams immediately post-liquefaction.

  • Standard
    23 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 20088-3:2019(Main)
Determination of the resistance to cryogenic spillage of insulation materials - Part 3: Jet release (ISO 20088-3:2018)
SIST EN ISO 20088-3:2020

This document describes a method for determining the resistance of a cryogenic spill protection (CSP) system to a cryogenic jet as a result of a pressurized release which does not result in immersion conditions. It is applicable where CSP systems are installed on carbon steel and will be in contact with cryogenic fluids.
A cryogenic jet can be formed upon release from process equipment operating at pressure (e.g. some liquefaction processes utilize 40 to 60 bar operating pressure). Due to high pressure discharge, the cryogenic spillage protection can be compromised by the large momentum combined with extreme cryogenic temperature.
Although the test uses liquid nitrogen as the cryogenic liquid, the test described in this document is representative of a release of LNG, through a 20 mm orifice or less, at a release pressure of 6 barg or less, based upon simulated parameters 1 m from the release point. Confidence in this test being representative is based upon a comparison of the expected dynamic pressure of the simulated release in comparison with dynamic pressure from releases in accordance with this document.
It is not practical in this test to cover the whole range of cryogenic process conditions found in real plant conditions; in particular the test does not cover high pressure cryogenic jet releases that might be found in refrigeration circuits and in LNG streams immediately post-liquefaction.
Liquid nitrogen is used as the cryogenic medium due to the ability to safely handle the material at the pressures described in this document. The test condition is run at nominally 8 barg pressure.
ISO 20088-1 covers cryogenic release scenarios which can lead to pooling conditions for steel work protected by cryogenic spill protection as a result of a jet release or low pressure release of LNG or liquid nitrogen. ISO 20088-2 covers vapour phase exposure conditions as a result of a jet release or low pressure release of LNG or liquid nitrogen.

  • Standard
    31 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 20088-1:2016(Main)
Determination of the resistance to cryogenic spillage of insulation materials - Part 1: Liquid phases (ISO 20088-1:2016)
SIST EN ISO 20088-1:2017

ISO 20088-1:2016 describes a method for determining the resistance to liquid cryogenic spillage on cryogenic spillage protection (CSP) systems. It is applicable where CSP systems are installed on carbon steel and will be in contact with cryogenic fluids.
Liquid nitrogen is used as the cryogenic medium since it has a lower boiling point than liquid natural gas or liquid oxygen and it is not flammable. Additionally, it can be safely used for experiment.
Future parts of the standard will cover vapour phase and jet exposure conditions.
The test laboratory is responsible to conduct an appropriate risk assessment according to local regulation in order to consider the impact of liquid and gaseous nitrogen exposure to equipment and personnel.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 16904:2016(Main)
Petroleum and natural gas industries - Design and testing of LNG marine transfer arms for conventional onshore terminals (ISO 16904:2016)
SIST EN ISO 16904:2016

ISO 16904:2016 specifies the design, minimum safety requirements and inspection and testing procedures for liquefied natural gas (LNG) marine transfer arms intended for use on conventional onshore LNG terminals, handling LNG carriers engaged in international trade. It can provide guidance for offshore and coastal operations. It also covers the minimum requirements for safe LNG transfer between ship and shore.
Although the requirements for power/control systems are covered, this International Standard does not include all the details for the design and fabrication of standard parts and fittings associated with transfer arms.
ISO 16904:2016 is supplementary to local or national standards and regulations and is additional to the requirements of ISO 28460.
ISO 16904:2016 needs not be applied to existing facilities.

  • Standard
    76 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN ISO 28460:2010(Main)
Petroleum and natural gas industries - Installation and equipment for liquefied natural gas - Ship-to-shore interface and port operations (ISO 28460:2010)
SIST EN ISO 28460:2011

ISO 28460:2010 specifies the requirements for ship, terminal and port service providers to ensure the safe transit of an LNG carrier through the port area and the safe and efficient transfer of its cargo. It is applicable to
          pilotage and vessel traffic services (VTS);
          tug and mooring boat operators;
          terminal operators;
          ship operators;
          suppliers of bunkers, lubricants and stores and other providers of services whilst the LNG carrier is moored alongside the terminal.
ISO 28460:2010 includes provisions for
       a ship's safe transit, berthing, mooring and unberthing at the jetty;
       cargo transfer;
       access from jetty to ship;
       operational communications between ship and shore;
       all instrumentation, data and electrical connections used across the interface, including OPS (cold ironing), where applicable;
       the liquid nitrogen connection (where fitted);
       ballast water considerations.
ISO 28460:2010 applies only to conventional onshore LNG terminals and to the handling of LNGC's in international trade. However, it can provide guidance for offshore and coastal operations.

  • Standard
    37 pages
    English language
    sale 10% off
    e-Library read for
    1 day