prEN ISO 10365

Adhesives - Designation of main failure patterns (ISO/DIS 10365:2020)

Klebstoffe - Bezeichnung der wichtigsten Bruchbilder (ISO/DIS 10365:2020)

Diese Internationale Norm legt die Bezeichnungen der wichtigsten Bruchbildarten von geklebten Fügeanordnungen fest und veranschaulicht durch Abbildungen ihr jeweiliges Aussehen.
Sie ist anwendbar bei allen mechanischen Prüfungen an einer geklebten Fügeanordnung, ungeachtet der Natur der Fügeteile und des Klebstoffes, die zur Herstellung der Fügeanordnung verwendet wurden.

Adhésifs - Désignation des principaux faciès de rupture (ISO/DIS 10365:2020)

Lepila - Označevanje glavnih načinov porušitev (ISO/DIS 10365:2020)

General Information

• Status: Not Published
• ICS: 83.180 - Adhesives
• Technical Committee: CEN/TC 193 - Adhesives
• Drafting Committee: CEN/TC 193/WG 2 - Structural adhesives
• Current Stage: 4599 - Dispatch of FV draft to CMC - Finalization for Vote
• Due Date: 27-Sep-2021
• Completion Date: 27-Sep-2021
• Ref Project: oSIST prEN ISO 10365:2020 - Adhesives - Designation of main failure patterns (ISO/DIS 10365:2020)

RELATIONS

• Revised: EN ISO 10365:1995 - Adhesives - Designation of main failure patterns (ISO 10365:1992)
• Effective Date: 10-Mar-2020

Standards Content (sample)

SLOVENSKI STANDARD
oSIST prEN ISO 10365:2020
01-julij-2020
Lepila - Označevanje glavnih načinov porušitev (ISO/DIS 10365:2020)
Adhesives - Designation of main failure patterns (ISO/DIS 10365:2020)
Klebstoffe - Bezeichnung der wichtigsten Bruchbilder (ISO/DIS 10365:2020)
Adhésifs - Désignation des principaux faciès de rupture (ISO/DIS 10365:2020)
Ta slovenski standard je istoveten z: prEN ISO 10365
ICS:
83.180 Lepila Adhesives
oSIST prEN ISO 10365:2020 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 10365:2020
---------------------- Page: 2 ----------------------
oSIST prEN ISO 10365:2020
DRAFT INTERNATIONAL STANDARD
ISO/DIS 10365
ISO/TC 61/SC 11 Secretariat: JISC
Voting begins on: Voting terminates on:
2020-05-06 2020-07-29
Adhesives — Designation of main failure patterns
Adhésifs — Désignation des principaux faciès de rupture
ICS: 83.180
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 10365:2020(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. ISO 2020
---------------------- Page: 3 ----------------------
oSIST prEN ISO 10365:2020
ISO/DIS 10365:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2020

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting

on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 10365:2020
ISO/DIS 10365:2020(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 Application ................................................................................................................................................................................................................. 1

© ISO 2020 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 10365:2020
ISO/DIS 10365:2020(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified duri
...