Adhesives - Test methods for adhesives for plastic or rubber floor coverings or wall coverings - Determination of dimensional changes after accelerated ageing (ISO 22635:2019)

This document specifies a test method that measures the dimensional changes of a plastic or rubber floor or wall covering bonded to a given substrate after accelerated ageing. The term "wall covering" does not include any type of wallpaper.

Klebstoffe - Prüfverfahren für Klebstoffe für Boden- und Wandbeläge aus Kunststoff oder Gummi - Bestimmung der Maßänderungen nach beschleunigter Alterung (ISO 22635:2019)

Dieses Dokument legt ein Prüfverfahren zur Bestimmung der Maßänderungen von Boden- oder Wandbelägen aus Kunststoff oder Gummi, die auf ein vorgegebenes Substrat geklebt sind und einer beschleunigten Alterung unterworfen wurden, fest. Die Benennung „Wandbelag“ umfasst keine Art von Papier-Wandtapeten.

Adhésifs - Méthodes d'essai des adhésifs pour revêtements de sol ou muraux en plastique ou en caoutchouc - Détermination des variations dimensionnelles après un vieillissement accéléré (ISO 22635:2019)

Le présent document spécifie une méthode d'essai pour mesurer les variations dimensionnelles d'un revêtement de sol ou mural en plastique ou en caoutchouc, collé sur un support donné après un vieillissement accéléré. Le terme « revêtement de mur » (ou « revêtement mural ») n'inclut aucun type de papier peint.

Lepila - Preskusna metoda za lepila za polimerne ali gumene talne in stenske obloge - Ugotavljanje sprememb mer po pospešenem staranju (ISO 22635:2019)

Ta evropski standard določa preskusno metodo, ki meri dimenzijske spremembe pri polimerni ali gumeni talni ali stenski oblogi, zlepljeni na dano podlago, po pospešenem staranju. Izraz »stenska obloga« ne zajema nobene vrste tapet.

General Information

Status
Published
Publication Date
30-Jul-2019
Technical Committee
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Due Date
31-Jul-2019
Completion Date
31-Jul-2019

RELATIONS

Buy Standard

Standard
EN ISO 22635:2019
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN ISO 22635:2019
01-oktober-2019
Nadomešča:
SIST EN 1903:2015
Lepila - Preskusna metoda za lepila za polimerne ali gumene talne in stenske
obloge - Ugotavljanje sprememb mer po pospešenem staranju (ISO 22635:2019)

Adhesives - Test method for adhesives for plastic or rubber floor coverings or wall

coverings - Determination of dimensional changes after accelerated ageing (ISO
22635:2019)

Klebstoffe - Prüfverfahren für Klebstoffe für Boden- und Wandbeläge aus Kunststoff oder

Gummi - Bestimmung der Maßänderungen nach beschleunigter Alterung (ISO
22635:2019)
Adhésifs - Méthodes d'essai des adhésifs pour revêtements de sol ou muraux en

plastique ou en caoutchouc - Détermination des variations dimensionnelles après un

vieillissement accéléré (ISO 22635:2019)
Ta slovenski standard je istoveten z: EN ISO 22635:2019
ICS:
83.180 Lepila Adhesives
SIST EN ISO 22635:2019 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 22635:2019
---------------------- Page: 2 ----------------------
SIST EN ISO 22635:2019
EN ISO 22635
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2019
EUROPÄISCHE NORM
ICS 83.180 Supersedes EN 1903:2015
English Version
Adhesives - Test method for adhesives for plastic or
rubber floor coverings or wall coverings - Determination
of dimensional changes after accelerated ageing (ISO
22635:2019)

Adhésifs - Méthodes d'essai des adhésifs pour Klebstoffe - Prüfverfahren für Klebstoffe für Boden-

revêtements de sol ou muraux en plastique ou en und Wandbeläge aus Kunststoff oder Gummi -

caoutchouc - Détermination des variations Bestimmung der Maßänderungen nach beschleunigter

dimensionnelles après un vieillissement accéléré (ISO Alterung (ISO 22635:2019)
22635:2019)
This European Standard was approved by CEN on 8 September 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this

European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by

translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management

Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and

United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 22635:2019 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 22635:2019
EN ISO 22635:2019 (E)
Contents Page

European foreword ....................................................................................................................................................... 3

---------------------- Page: 4 ----------------------
SIST EN ISO 22635:2019
EN ISO 22635:2019 (E)
European foreword

This document (EN ISO 22635:2019) has been prepared by Technical Committee ISO/TC 61 "Plastics"

in collaboration with Technical Committee CEN/TC 193 “Adhesives” the secretariat of which is held by

UNE.

This European Standard shall be given the status of a national standard, either by publication of an

identical text or by endorsement, at the latest by January 2020, and conflicting national standards shall

be withdrawn at the latest by January 2020.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CEN shall not be held responsible for identifying any or all such patent rights.

This document supersedes EN 1903:2015.

According to the CEN-CENELEC Internal Regulations, the national standards organizations of the

following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,

Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,

Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of

North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the

United Kingdom.
Endorsement notice

The text of ISO 22635:2019 has been approved by CEN as EN ISO 22635:2019 without any modification.

---------------------- Page: 5 ----------------------
SIST EN ISO 22635:2019
---------------------- Page: 6 ----------------------
SIST EN ISO 22635:2019
INTERNATIONAL ISO
STANDARD 22635
First edition
2019-07
Adhesives — Test methods for
adhesives for plastic or rubber
floor coverings or wall coverings
— Determination of dimensional
changes after accelerated ageing
Adhésifs — Méthodes d'essai des adhésifs pour revêtements de sol
ou muraux en plastique ou en caoutchouc — Détermination des
variations dimensionnelles après un vieillissement accéléré
Reference number
ISO 22635:2019(E)
ISO 2019
---------------------- Page: 7 ----------------------
SIST EN ISO 22635:2019
ISO 22635:2019(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2019

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting

on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address

below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 22635:2019
ISO 22635:2019(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

1 Scope ................................................................................................................................................................................................................................. 1

2 Normative references ...................................................................................................................................................................................... 1

3 Terms and definitions ..................................................................................................................................................................................... 1

4 Principle ........................................................................................................................................................................................................................ 2

5 Apparatus and materials.............................................................................................................................................................................. 2

6 Preparation of test specimens ................................................................................................................................................................ 4

6.1 Conditioning of fibre cement substrate ............................................................................................................................. 4

6.2 Conditioning of test covering ......... ............................................................................................................................................. 5

6.2.1 Room temperature storage ..................................................................................................................................... 5

6.2.2 Elevated temperature pre-treatment ............................................................................................................. 5

6.3 Sampling and conditioning of adhesive ............................................................................................................................. 5

6.4 Datum points ............................................................................................................................................................................................ 5

6.4.1 Fixing of gauge positions .......................................................................................................................................... 5

6.4.2 Edge to edge measurements .................................................................................................................................. 5

6.5 Initial measurements of dimensions prior to bonding ........................................................................................ 5

6.6 Preparation of bonded test specimens ............................................................................................................................... 6

6.6.1 Cleaning ................................................................................................................................................................................... 6

6.6.2 Application of adhesive .............................................................................................................................................. 6

6.6.3 Bonding .................................................................................................................................................................................... 6

7 Procedure..................................................................................................................................................................................................................... 6

7.1 Preconditioning ...................................................................................................................................................................................... 6

7.2 Conditioning cycle (accelerated ageing) ........................................................................................................................... 6

7.3 Subsequent cycles ................................................................................................................................................................................ 6

8 Evaluation and expression of results .............................................................................................................................................. 7

9 Test report ................................................................................................................................................................................................................... 7

© ISO 2019 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 22635:2019
ISO 22635:2019(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www .iso .org/patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information abo
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.