EN ISO 19085-12:2024
(Main)Woodworking machines - Safety - Part 12: Tenoning-profiling machines (ISO 19085-12:2024)
Woodworking machines - Safety - Part 12: Tenoning-profiling machines (ISO 19085-12:2024)
This document specifies the safety requirements and measures for manually loaded and unloaded
— single-end tenoning machines with a manual feed sliding table,
— single-end tenoning machines with a mechanical feed sliding table,
— single-end tenoning-profiling machines with mechanical feed,
— double-end tenoning-profiling machines with mechanical feed, also designed to be automatically either loaded or unloaded, or both, and
— angular systems for tenoning and profiling with mechanical feed
with maximum workpiece height capacity of 200 mm for single-end machines and 500 mm for double-end machines, capable of continuous production use, altogether referred to as “machines”.
This document deals with all significant hazards, hazardous situations and events as listed in Annex A, relevant to machines, when operated, adjusted and maintained as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Also, transport, assembly, dismantling, disabling and scrapping phases have been taken into account.
The machines are designed to process in one pass one end or two sides, either opposite or perpendicular to each other, of workpieces made of
a) solid wood, and
b) materials with similar physical characteristics to wood (see ISO 19085-1:2021, 3.2); and
c) only the machines with mechanical feed, made of
d) fibre-cement,
e) rock wool and glass wool,
f) gypsum,
g) plasterboard,
h) matrix engineered mineral boards, silicate boards and sulfate boards,
i) composite materials with core consisting of polyurethane or mineral material laminated with light alloy,
j) polymer-matrix composite materials and reinforced thermoplastic, thermoset and elastomeric materials,
k) aluminium light alloy profiles, and
l) composite boards made from the materials listed above.
This document is also applicable to machines fitted with one or more of the following devices or additional working units, whose hazards have been dealt with:
— sanding units;
— fixed or movable workpiece support;
— automatic tool changing;
— automatic workpiece returner;
— glass bead saw unit;
— hinge recessing unit;
— boring unit;
— dynamic processing unit;
— sawing unit installed out of the integral enclosure, between machine halves in double-end machines;
— foiling unit;
— coating unit;
— grooving unit with a milling tool installed out of the integral enclosure, between machine halves;
— brushing unit;
— gluing unit;
— sealing unit;
— dowels inserting unit;
— tongues inserting unit;
— inkjet marking unit;
— laser marking unit;
— labelling unit;
— workpiece back-up device (device that is either anti-chipping or anti-splintering, or both);
— quick tool changing system;
— post-formed edge pre-cutting unit;
— additional workpiece support (at either infeed or outfeed, or both);
— parallel infeed device on single-end machines;
— transversal infeed device on single-end machines;
— intermediate workpiece support on double-end machines;
— automatic infeed device;
— feed chain with dogs.
This document does not deal with any hazards related to:
a) systems for automatic loading and unloading of the workpiece to a single machine other than automatic workpiece returner;
b) single machine being used in combination with any other machine (as part
Holzbearbeitungsmaschinen - Sicherheit - Teil 12: Zapfenschneid- und Schlitzmaschinen/Profiliermaschinen (ISO 19085-12:2024)
Dieses Dokument stellt Sicherheitsanforderungen und Maßnahmen zur Verfügung für stationäre, manuell be- und entladene:
- einseitige Zapfenschneid- und Schlitzmaschinen mit handbetätigtem Vorschubtisch;
- einseitige Zapfenschneid- und Schlitzmaschinen mit mechanischem Vorschubtisch;
- einseitige Zapfenschneid- und Schlitzmaschinen und/oder Profiliermaschinen mit mechanischem Vorschub;
- doppelseitige Zapfenschneid- und Schlitzmaschinen und/oder Profiliermaschinen mit mechanischem Vorschub, auch wenn sie für automatische Beschickung/Entnahme gestaltet sind;
- Winkelanlagen für das Zapfenschneiden/Schlitzen und Profilieren mit mechanischem Vorschub,
mit Handbeschickung und -entnahme und einer größten Werkstückhöhenkapazität von 200 mm für einseitige Maschinen und 500 mm für doppelseitige Maschinen, nachfolgend als „Maschinen“ bezeichnet.
Es behandelt alle im Abschnitt 4 aufgeführten signifikanten Gefährdungen, Gefährdungssituationen und Gefährdungsereignisse, die auf die Maschinen zutreffen, wenn sie bestimmungsgemäß und entsprechend den vorhersehbaren Bedingungen des Herstellers verwendet, eingestellt und gewartet werden, einschließlich der vernünftigerweise vorhersehbaren Fehlanwendung. Ferner wurden Transport, Zusammenbau, Demontage, Rückbau und Verschrottung berücksichtigt.
ANMERKUNG Hinsichtlich zutreffender, aber nicht signifikanter Gefährdungen, z. B. scharfe Kanten des Maschinengestells, siehe ISO 12100:2010.
Die Maschinen sind so gestaltet, dass sie in einem Durchgang einseitig oder zweiseitig, entweder gegenüberliegend oder senkrecht zueinander, Werkstücke aus
1) Massivholz;
2) Werkstoffen mit ähnlichen physikalischen Eigenschaften wie Holz (siehe ISO 19085-1:2017, 3.2);
3) Faserzement-, Stein-/Glaswolle-, Gips-, Gipskartonplatten, nur bei Maschinen mit mechanischem Vorschub
bearbeiten können.
Es gilt auch für Maschinen, die mit einem oder mehreren der folgenden zusätzlichen Arbeitsaggregate ausgestattet sind, deren Gefährdungen berücksichtigt wurden:
- Schleifaggregate;
- feststehende oder bewegliche Werkstückauflagen;
- automatischer Werkzeugwechsel;
- automatische Werkstück-Rückführung;
- Glasleistensägeaggregat;
- Beschlageinlass-Fräsaggregat;
- Postforming-Aggregat;
- Bohraggregat;
- dynamisches Bearbeitungsaggregat;
- außerhalb der Teilkapselung installiertes Sägeaggregat, das bei doppelseitigen Maschinen zwischen den Maschinenhälften angeordnet ist;
- Aggregat zum Folieren;
- Aggregat zum Beschichten;
- Nutaggregat mit Fräswerkzeugen, das außerhalb der Teilkapselung zwischen den Maschinenhälften angeordnet ist;
- Aggregat zum Bürsten;
- Aggregat zum Beleimen;
- Aggregat zum Versiegeln;
- Aggregat zum Dübelsetzen;
- Aggregat zum Einsetzen von Federn;
- Aggregat zum Beschriften mittels Inkjetdruck;
- Aggregat zum Beschriften mittels Laser;
- Aggregat zum Kennzeichnen;
- Werkstückgegenhalter (Splitterreißschutz);
- Werkzeug-Schnellwechselsystem.
Dieses Dokument behandelt keine Gefährdungen im Zusammenhang mit:
a) Systemen zum automatischen Beschicken und Entnehmen des Werkstücks an einer einzelnen Maschine, ausgenommen die automatische Werkstück-Rückführung;
b) Einzelmaschinen, die in Kombination mit irgendeiner anderen Maschine (als Teil einer Linie) verwendet werden;
c) der Verwendung von Werkzeugen, ausgenommen Sägeblätter oder Fräswerkzeuge zum Nuten, die bei doppelseitigen Maschinen zwischen den Maschinenhälften außerhalb der Teilkapselung angeordnet sind;
d) der Verwendung von Werkzeugen, die über die Teilkapselung hervorstehen;
e) den chemischen Eigenschaften von Faserzement-, Stein-/Glaswolle-, Gips-, Gipskartonplatten und deren Stäuben.
Es gilt nicht für Maschinen, die zur bestimmungsgemäßen Verwendung in potentiell explosiven Atmosphären vorgesehen sind oder Maschinen, die vor seinem Ausgabedatum hergestellt werden.
Machines à bois - Sécurité - Partie 12: Machines à tenonner-profiler (ISO 19085-12:2024)
Le présent document donne les exigences et mesures de sécurité pour les machines fixes, à chargement et déchargement manuels:
— tenonneuses simples à table mobile à avance manuelle;
— tenonneuses simples à table mobile à avance mécanisée;
— machines à tenonner et/ou profiler simples à avance mécanisée;
— machines à tenonner et/ou profiler doubles à avance mécanisée, également conçues pour être chargées/déchargées automatiquement;
— systèmes angulaires pour tenonnage et profilage à avance mécanisée;
ayant une capacité de hauteur de pièce maximale de 200 mm pour les machines simples et de 500 mm pour les machines doubles, ci-après désignées «machines».
Il traite de tous les phénomènes dangereux, situations et événements dangereux significatifs, tels qu'énumérés à l'Article 4, applicables aux machines lorsqu'elles sont utilisées, réglées et entretenues comme prévu et dans les conditions prévues par le fabricant, incluant une mauvaise utilisation raisonnablement prévisible. Les phases de transport, d'assemblage, de démontage, de mise hors service et de mise au rebut sont également prises en compte.
NOTE Pour les phénomènes dangereux pertinents mais non significatifs, par exemple, les arêtes vives du bâti de la machine, voir l'ISO 12100:2010.
Les machines sont conçues pour usiner en une seule passe une extrémité ou deux chants, soit opposés, soit perpendiculaires l'un à l'autre, de pièces constituées de:
1) bois massif;
2) matériaux ayant des caractéristiques physiques similaires à celles du bois (voir l'ISO 19085-1:2017, 3.2);
3) fibre-ciment, laine de roche/verre, plâtre, plaque de plâtre, uniquement avec des machines à avance mécanisée.
Il est également applicable aux machines équipées d'une ou plusieurs des unités de travail supplémentaires suivantes, dont les phénomènes dangereux ont été traités:
— unités de ponçage;
— support de pièce fixe ou mobile;
— changement automatique d'outil;
— dispositif de retour automatique de la pièce;
— unité de sciage de parclose;
— unité de mortaisage;
— unité de précoupe de chant postformé;
— unité d'alésage;
— unité dynamique;
— unité de sciage installée à l'extérieur de l'enceinte intégrée, entre les demi-machines dans les machines doubles;
— unité de placage;
— unité d'enrobage;
— unité de rainurage avec outil de fraisage installée à l'extérieur de l'enceinte intégrée, entre les demi-machines;
— unité de brossage;
— unité de collage;
— unité de scellement;
— unité d'insertion de chevilles;
— unité d'insertion de languettes;
— unité de marquage par jet d'encre;
— unité de marquage par laser;
— unité d'étiquetage;
— dispositif de protection de la pièce (dispositif anti-écaillage/anti-flâches);
— système de changement rapide d'outil.
Le présent document ne traite pas des phénomènes dangereux relatifs:
a) aux systèmes de chargement et déchargement automatiques de la pièce d'une machine simple autres qu'un dispositif de retour automatique de la pièce;
b) à une machine simple utilisée en combinaison avec toute autre machine (comme partie d'une ligne);
c) à l'utilisation d'outils autres que des lames de scie ou des outils de fraisage pour le rainurage, installés entre des demi-machines et à l'extérieur de l'enceinte intégrée dans des ma
Lesnoobdelovalni stroji - Varnost - 12. del: Stroji za izdelovanje čepov in utorov/profilni stroji (ISO 19085-12:2024)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-april-2025
Nadomešča:
SIST EN ISO 19085-12:2021/A11:2023
Lesnoobdelovalni stroji - Varnost - 12. del: Stroji za izdelovanje čepov in
utorov/profilni stroji (ISO 19085-12:2024)
Woodworking machines - Safety - Part 12: Tenoning/profiling machines (ISO 19085-
12:2024)
Holzbearbeitungsmaschinen - Sicherheit - Teil 12: Zapfenschneid- und
Schlitzmaschinen/Profiliermaschinen (ISO 19085-12:2024)
Machines à bois - Sécurité - Partie 12: Machines à tenonner-profiler (ISO 19085-
12:2024)
Ta slovenski standard je istoveten z: EN ISO 19085-12:2024
ICS:
13.110 Varnost strojev Safety of machinery
79.120.10 Lesnoobdelovalni stroji Woodworking machines
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 19085-12
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2024
EUROPÄISCHE NORM
ICS 13.110; 79.120.10 Supersedes EN ISO 19085-12:2021
English Version
Woodworking machines - Safety - Part 12: Tenoning-
profiling machines (ISO 19085-12:2024)
Machines à bois - Sécurité - Partie 12: Machines à Holzbearbeitungsmaschinen - Sicherheit - Teil 12:
tenonner-profiler (ISO 19085-12:2024) Zapfenschneid- und
Schlitzmaschinen/Profiliermaschinen (ISO 19085-
12:2024)
This European Standard was approved by CEN on 28 September 2024.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 19085-12:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2006/42/EC aimed to be covered . 4
European foreword
This document (EN ISO 19085-12:2024) has been prepared by Technical Committee ISO/TC 39
"Machine tools" in collaboration with Technical Committee CEN/TC 142 “Woodworking machines -
Safety” the secretariat of which is held by UNI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2025, and conflicting national standards shall be
withdrawn at the latest by June 2025.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 19085-12:2021.
This document has been prepared under a standardization request addressed to CEN by the European
Commission. The Standing Committee of the EFTA States subsequently approves these requests for its
Member States.
For the relationship with EU Legislation, see informative Annex ZA, which is an integral part of this
document.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 19085-12:2024 has been approved by CEN as EN ISO 19085-12:2024 without any
modification.
Annex ZA
(informative)
Relationship between this European Standard and the essential
requirements of Directive 2006/42/EC aimed to be covered
This European Standard has been prepared under a Commission’s standardization request “M/396
Mandate to CEN and CENELEC for Standardisation in the field of machinery” to provide one voluntary
means of conforming to essential requirements of Directive 2006/42/EC of the European Parliament
and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast).
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding essential requirements
of that Directive and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Annex I of Directive
2006/42/EC
The relevant Essential Requirements of Directive Clause(s)/subclause(s) Remarks/Note
2006/42/EC of this EN s
1.1.2 Principles of safety integration
a) fitted for its function Clauses 4, 5, 6, 7
c) intended use and reasonably foreseeable misuse Clauses 4, 5, 6, 7
d) constraints in use Clauses 4, 5, 6, 7
1.1.3 Materials and products 6.3, 6.16
1.1.4 Lighting 6.6, 7.3.1
1.1.5 Design of machinery to facilitate its handling 6.5, 7.3
1.1.6 Ergonomics 6.5
1.2.1 Safety and reliability of control systems 4.1, 4.3, 6.7, 6.8
1.2.2 Control devices 4.2, 4.3, 4.4, 4.6, 4.7
1.2.3 Starting 4.3
1.2.4 Stopping 4.4, 4.5, 5.4
1.2.5 Selection of control or operating mode 4.6
1.2.6 Failure of the power supply 4.8, 6.7, 6.8, 6.16
1.3.1 Risk of loss of stability 5.1, 7.3
1.3.2 Risk of break-up during operation 4.3, 5.2, 5.3, 5.9, 6.14, 7.3
1.3.3 Risks due to falling or ejected objects 5.2, 5.3, 5.5, 5.8, 5.9, 7.3
1.3.6 Risks relating to variations in the operating 4.6, 4.7, 5.6
conditions
1.3.7 Risks related to moving parts 5.5, 5.6, 5.7, 5.8, 7.3
1.3.8 Choice of protection against risks related to moving 5.6, 5.7, 5.8
parts
1.3.9 Risk of uncontrolled movements 4.1, 4.3, 4.5, 4.8, 5.4
1.4.1 General requirements 5.9
1.4.2.1 Fixed guards 5.5.1
1.4.2.2 Interlocking movable guards 5.5.2
1.4.3 Special requirements for protective devices 5.5.3, 5.5.5, 5.5.6
1.5.1 Electricity supply 6.4, 6.13
1.5.2 Static electricity 6.11
1.5.3 Energy supply other than electricity 6.7, 6.8
1.5.4 Errors of fitting 6.12
1.5.5 Extreme temperatures 6.16
1.5.6 Fire 6.1
1.5.8 Noise 6.2, Annex F
1.5.11 External radiation 6.9
1.5.12 Laser equipment 6.10
1.5.13 Emission of hazardous materials and substances 6.3, 6.17
1.6.1 Machinery maintenance 6.14, 7.3
1.6.2 Access to operating position and servicing points 6.14, 7.3
1.6.3 Isolation of energy sources 6.13, 7.3
1.6.4 Operator intervention 6.14, 7.3
1.6.5 Cleaning of internal parts 6.14, 7.3
1.7.1 Information and warnings on the machinery 6.10, 7.1, 7.2
1.7.2 Warning of residual risks 6.10, 7.1
1.7.3 Marking of machinery 7.2
1.7.4 Instructions 6.10, 7.3, Annex F
2.3 Machinery for working wood and analogous
materials
a) guiding 5.1, 5.10
b) ejection 5.9, 7.3
c) brake 4.5, 5.4
d) accidental tool contact 5.6, 7.3
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
International
Standard
ISO 19085-12
Second edition
Woodworking machines — Safety —
2024-11
Part 12:
Tenoning-profiling machines
Machines à bois — Sécurité —
Partie 12: Machines à tenonner-profiler
Reference number
ISO 19085-12:2024(en) © ISO 2024
ISO 19085-12:2024(en)
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 19085-12:2024(en)
Contents Page
Foreword .vi
Introduction .vii
1 Scope . 1
2 Normative references . 3
3 Terms and definitions . 3
4 Safety requirements and measures for controls .16
4.1 Safety and reliability of control systems.16
4.2 Control devices .16
4.2.1 General .17
4.2.2 Single-end tenoning machines with a manual feed sliding table .17
4.2.3 Single-end tenoning machines with a mechanical feed sliding table .17
4.2.4 Single-end tenoning-profiling machines with mechanical feed .17
4.2.5 Double-end tenoning-profiling machines with mechanical feed .17
4.2.6 Angular systems for tenoning and profiling with mechanical feed .17
4.3 Start .18
4.3.1 Direct start .18
4.3.2 Start via control power-on .18
4.3.3 Laser marking unit .18
4.4 Safe stops .18
4.4.1 General .18
4.4.2 Normal stop .19
4.4.3 Operational stop .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.