Fasteners - Acceptance inspection (ISO 3269:2019)

This document specifies an inspection procedure to be used by the purchaser where no prior agreement exists.
It also specifies a reference acceptance procedure for acceptance or rejection of an inspection lot, when no agreement can be reached between the purchaser and the supplier, or where conformance to specification is disputed.
It applies to inspection lots of bolts, screws, studs, nuts, pins, washers, rivets and other related fasteners.
This document applies to fasteners not intended for high volume machine assembly, special-purpose applications or specially engineered applications requiring more advanced in-process control and lot traceability.
For in-process control or final inspection by the manufacture and sorting, see ISO 16426.

Mechanische Verbindungselemente - Annahmeprüfung (ISO 3269:2019)

Dieses Dokument legt ein Prüfverfahren fest, das vom Käufer anzuwenden ist, wenn keine vorherige Ver-einbarung vorliegt.
Es legt außerdem auch ein Schieds Annahmeverfahren für die Annahme oder Rückweisung eines Prüfloses fest, wenn keine Vereinbarung zwischen dem Käufer und dem Lieferanten erzielt werden kann, oder wenn die Übereinstimmung mit der Spezifikation angezweifelt wird.
Es gilt für Prüflose von Schrauben, Bolzen, Muttern, Stiften, Scheiben, Nieten und weiteren ähnlichen Ver-bindungselementen.
Dieses Dokument gilt für Verbindungselemente, die nicht für den Zusammenbau von Hochleistungs-maschinen, Anwendungen für besondere Zwecke oder speziell entwickelte Anwendungen vorgesehen sind, die eine weitergehende Prozessüberwachung und Rückverfolgbarkeit der Lose erfordern.
Für die Prozessüberwachung oder Endprüfung bei der Herstellung und Sortierung, siehe ISO 16426.

Fixations - Contrôle réception (ISO 3269:2019)

Le présent document spécifie une procédure de contrôle à appliquer par le client si aucun accord préalable n'a été conclu.
Il spécifie également une procédure de réception de référence pour l'acceptation ou le rejet d'un lot de contrôle lorsqu'aucun accord n'a pu être conclu entre le client et le fournisseur, ou lorsque la conformité à la spécification fait l'objet d'un litige.
Il s'applique aux lots de réception de boulons, vis, goujons, écrous, goupilles, rondelles, rivets et autres fixations associées.
Le présent document s'applique aux fixations non destinées aux machines d'assemblage à gros débit, à des applications spéciales, ou à des applications particulières nécessitant un contrôle en cours de fabrication plus poussé et une traçabilité des lots.
Pour le contrôle en cours de fabrication, le contrôle final par le fabricant ou le contrôle par tri, voir l'ISO 16426.

Vezni elementi - Prevzemna kontrola (ISO 3269:2019)

Ta dokument določa postopek prevzemne kontrole, ki ga lahko uporabi kupec, če predhodnega dogovora ni. Prav tako določa referenčni postopek za prevzem ali zavrnitev kontrolne serije, kadar med kupcem in dobaviteljem ni mogoče doseči dogovora ali če je skladnost s specifikacijami sporna. Velja za kontrolne serije sornikov, vijakov, zatičev, matic, moznikov, podložk, zakovic in drugih povezanih veznih elementov. Dokument se uporablja za vezne elemente, ki niso namenjeni za montažo strojev masovne proizvodnje, posebne namene ali posebne vrste uporabe, pri katerih se zahteva naprednejša kontrola postopka in sledljivost serije. Za kontrolo med postopkom ali končno kontrolo v proizvodnji in sortiranje glej ISO 16426.

General Information

Publication Date
Withdrawal Date
Current Stage
6060 - Definitive text made available (DAV) - Publishing
Start Date
Completion Date


Buy Standard

EN ISO 3269:2019
English language
18 pages
sale 10% off
sale 10% off
e-Library read for
1 day

Standards Content (Sample)

SIST EN ISO 3269:2019
SIST EN ISO 3269:2002
Vezni elementi - Prevzemna kontrola (ISO 3269:2019)
Fasteners - Acceptance inspection (ISO 3269:2019)
Mechanische Verbindungselemente - Annahmeprüfung (ISO 3269:2019)
Fixations - Contrôle réception (ISO 3269:2019)
Ta slovenski standard je istoveten z: EN ISO 3269:2019
21.060.01 Vezni elementi na splošno Fasteners in general
SIST EN ISO 3269:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 3269:2019

---------------------- Page: 2 ----------------------
SIST EN ISO 3269:2019

EN ISO 3269


September 2019
ICS 21.060.01 Supersedes EN ISO 3269:2000
English Version

Fasteners - Acceptance inspection (ISO 3269:2019)
Fixations - Contrôle réception (ISO 3269:2019) Mechanische Verbindungselemente - Annahmeprüfung
(ISO 3269:2019)
This European Standard was approved by CEN on 4 July 2019.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.



CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3269:2019 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 3269:2019
EN ISO 3269:2019 (E)
Contents Page
European foreword . 3


---------------------- Page: 4 ----------------------
SIST EN ISO 3269:2019
EN ISO 3269:2019 (E)
European foreword
This document (EN ISO 3269:2019) has been prepared by Technical Committee ISO/TC 2 "Fasteners" in
collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2020, and conflicting national standards shall
be withdrawn at the latest by March 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 3269:2000.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 3269:2019 has been approved by CEN as EN ISO 3269:2019 without any modification.


---------------------- Page: 5 ----------------------
SIST EN ISO 3269:2019

---------------------- Page: 6 ----------------------
SIST EN ISO 3269:2019
Fourth edition
Fasteners — Acceptance inspection
Fixations — Contrôle réception
Reference number
ISO 3269:2019(E)
ISO 2019

---------------------- Page: 7 ----------------------
SIST EN ISO 3269:2019
ISO 3269:2019(E)

© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on th

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.