EN 131-2:2010
(Main)Ladders - Part 2: Requirements, testing, marking
Ladders - Part 2: Requirements, testing, marking
This European Standard specifies the general design features, requirements and test methods for portable ladders.
It does not apply to step stools or ladders for specific professional use such as firebrigade ladders, roof ladders and mobile ladders.
It does not apply to ladders used for work on or near live electrical systems or installations. For this purpose EN 61478 applies.
This European Standard is intended to be used in conjunction with EN 131 1.
For single or multiple hinge joint ladders EN 131 4 applies.
Leitern - Teil 2: Anforderungen, Prüfung, Kennzeichnung
Diese Europäische Norm legt die allgemeinen Konstruktionsmerkmale, Anforderungen und Prüfverfahren für
tragbare Leitern fest.
Er gilt nicht für Tritte oder Leitern für den besonderen beruflichen Gebrauch, wie Feuerwehrleitern, Dachleitern
und fahrbare Leitern.
Er gilt nicht für Leitern, die für Arbeiten an oder in der Nähe von elektrischen Systemen verwendet werden.
Hierfür gilt EN 61478.
ANMERKUNG Für isolierende Leitern für Arbeiten an oder in der Nähe elektrischer Anlagen im Niederspannungsbereich
unter 1 000 V Wechselspannung oder 1 500 V Gleichspannung ist EN 50528 in Vorbereitung.
Diese Europäische Norm ist in Zusammenhang mit EN 131-1 anzuwenden.
Für Ein- oder Mehrgelenkleitern gilt EN 131-4.
Échelles - Partie 2: Exigences, essais, marquage
La présente Norme européenne spécifie les caractéristiques générales de conception, les exigences et les
méthodes d’essai applicables aux échelles portables.
Elle ne s’applique pas aux marchepieds ou aux échelles à usage professionnel spécifique tels que les
échelles à incendie, les échelles de toit et les échelles escamotables.
Elle ne s’applique pas aux échelles utilisées pour effectuer des travaux sur des installations électriques ou à
proximité de circuits électriques sous tension. À cet effet, l’EN 61478 s’applique.
NOTE Pour les échelles à caractères isolants (une tension inférieure à 1 000 V c.a. ou à 1 500 V c.c.), l’EN 50528
est en préparation.
La présente norme doit être utilisée conjointement avec l’EN 131-1.
Pour les échelles articulées à articulations simple et multiple, l’EN 131-4 s’applique.
Lestve - 2. del: Zahteve, preskušanje, označevanje
Ta evropski standard določa splošne konstrukcijske značilnosti, zahteve in preskusne metode za prenosne lestve. Ne velja za stopničaste stole ali lestve za posebno profesionalno uporabo, kot so gasilske lestve, strešne lestve in premične lestve. Ne velja za lestve, ki se uporabljajo za delo na ali v bližini električnih sistemov ali napeljav pod napetostjo. Za ta namen velja EN 61478.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Leitern - Teil 2: Anforderungen, Prüfung, KennzeichnungEchelles - Partie 2: Exigences, essais, marquageLadders - Part 2: Requirements, testing, marking97.145LestveLaddersICS:Ta slovenski standard je istoveten z:EN 131-2:2010SIST EN 131-2:2010en,de01-september-2010SIST EN 131-2:2010SLOVENSKI
STANDARDSIST EN 131-2:1996/AC:2001SIST EN 131-2:19961DGRPHãþD
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 131-2
June 2010 ICS 97.145 Supersedes EN 131-2:1993English Version
Ladders - Part 2: Requirements, testing, marking
Échelles - Partie 2: Exigences, essais, marquage
Leitern - Teil 2: Anforderungen, Prüfung, Kennzeichnung This European Standard was approved by CEN on 20 May 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 131-2:2010: ESIST EN 131-2:2010
Test sequence . 34Annex B (informative)
A-deviations . 35Bibliography . 38 SIST EN 131-2:2010
Introduction Due to the unhomogeneity of the material wood, special requirements have been appropriated on this item.
It does not apply to ladders used for work on or near live electrical systems or installations. For this purpose EN 61478 applies.
NOTE For insulating ladders for use on or near low voltage electrical installations in the range below 1000 V a.c or
1 500 V d.c. EN 50528 is under preparation.
This European Standard is intended to be used in conjunction with EN 131-1. For single or multiple hinge joint ladders EN 131-4 applies. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 59, Glass reinforced plastics — Measurement of hardness by means of a Barcol impressor EN 131-1:2007, Ladders — Part 1: Terms, types, functional sizes EN 131-3, Ladders — Part 3: User Instructions EN 204, Classification of thermoplastic wood adhesives for non-structural applications EN 301, Adhesives, phenolic and aminoplastic, for load-bearing timber structures — Classification and performance requirements EN 385, Finger jointed structural timber — Performance requirements and minimum production requirements EN 386:2001, Glued laminated timber — Performance requirements and minimum production requirements EN 391:2001, Glued laminated timber — Delamination test of glue lines EN 392, Glued laminated timber — Shear test of glue lines EN 408, Timber structures — Structural timber and glued laminated timber — Determination of some physical and mechanical properties EN 844-9:1997, Round and sawn timber — Terminology — Part 9: Terms relating to features of sawn timber EN 1310, Round and sawn timber — Method of measurement of features EN 61478, Live working — Ladders of insulating material (IEC 61478:2001) EN ISO 179-1, Plastics — Determination of Charpy impact properties — Part 1: Non-instrumented impact test (ISO 179-1:2000) SIST EN 131-2:2010
EN ISO 6892-1 of minimum 5 %. All load bearing parts made of aluminium alloy shall have a thickness of at least 1,2 mm. 4.2.2 Steel If cold rolled steel or a special alloy-steel is used the ratio between 0,2 % yield-stress and ultimate strength (Rp 0,2/Rm) shall be lower than 0,92. All load bearing parts made of steel shall have a thickness of at least 1,0 mm. 4.2.3 Plastics Glass-fibre reinforced plastics shall be protected against penetration of water and dirt. The surface shall be smooth. The fibres shall be embedded. The Barcol hardness according to EN 59 shall be at least 35. The test methods and acceptance criteria for de
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.