EN 474-2:2006+A1:2008
(Main)Earth-moving machinery - Safety - Part 2: Requirements for tractor-dozers
Earth-moving machinery - Safety - Part 2: Requirements for tractor-dozers
This part of EN 474 deals with all significant hazards, hazardous situations and events relevant to wheel and crawler tractor-dozers as defined in EN ISO 6165:2006, when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Clause 4).
This part also deals with rear-mounted winches for use on tractor-dozers.
The requirements of this part are complementary to the common requirements formulated in EN 474-1:2006.
This part does not repeat the requirements from EN 474-1:2006, but adds or replaces the requirements for application for tractor-dozers.
This part specifies the appropriate technical measures to eliminate or reduce risks arising from the significant hazards, hazardous situations and events during commissioning, operation and maintenance of tractor-dozers.
This European Standard is not applicable to tractor-dozers manufactured before the date of publication of this European Standard by CEN.
Erdbaumaschinen - Sicherheit - Teil 2: Anforderungen für Planiermaschinen
Dieser Teil der EN 474 behandelt alle signifikanten Gefährdungen, Gefährdungssituationen und Gefährdungsereignisse, die auf Rad- und Raupenplaniermaschinen, wie in EN ISO 6165:2006 definiert, zutreffen, wenn sie bestimmungsgemäß verwendet werden. Die nach vernünftigem Ermessen für den Hersteller vorhersehbare Nutzung der Maschine außerhalb der bestimmungsgemäßen Verwendung ist ebenfalls berücksichtigt (siehe Abschnitt 4).
Dieser Teil behandelt auch den Einsatz von Heckwinden auf Planiermaschinen.
Die Anforderungen gelten ergänzend zu den allgemeinen Anforderungen der EN 474-1:2006+A1:2009.
Dieser Teil wiederholt nicht die Anforderungen der EN 474-1:2006+A1:2009, aber ergänzt oder ersetzt relevante Anforderungen für Planiermaschinen.
Dieser Teil beschreibt die geeigneten technischen Maßnahmen, die erforderlich sind, die Risiken, die aufgrund signifikanter Gefährdungen, Gefährdungssituationen und Gefährdungsereignisse, die während der Inbetriebnahme, des Betriebes und der Instandhaltung von Planiermaschinen eintreten können, zu mindern
oder zu beseitigen.
Diese Europäische Norm ist nicht auf Planiermaschinen anzuwenden, die vor der Veröffentlichung dieser Europäischen Norm durch CEN hergestellt wurden.
Engins de terrassement - Sécurité - Partie 2: Prescriptions applicables aux bouteurs
La présente partie de l’EN 474 traite de tous les phénomènes, situations et événements dangereux significatifs
relatifs aux bouteurs à roues et à chenilles définis dans l'EN ISO 6165:2006 lorsqu'ils sont utilisés comme prévu
ou dans des conditions de mauvais usage que le fabricant peut raisonnablement prévoir (voir Article 4).
La présente partie traite également des treuils montés à l’arrière de bouteurs.
Les prescriptions figurant dans la présente partie viennent en complément des prescriptions communes présentées
dans l’EN 474-1:2006!+A1:2009".
La présente partie ne répète pas les prescriptions de l’EN 474-1:2006!+A1:2009" mais en ajoute ou en remplace
certaines applicables aux bouteurs.
La présente partie prescrit les mesures techniques appropriées pour éliminer ou réduire les risques dus
aux phénomènes, situations et événements dangereux significatifs survenant lors de la mise en service,
du fonctionnement et de la maintenance des bouteurs.
La présente Norme européenne ne s'applique pas aux bouteurs fabriqués avant la publication de la présente
Norme européenne par le CEN.
Stroji za zemeljska dela - Varnost - 2. del: Zahteve za buldožerje
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2008
Stroji za zemeljska dela - Varnost - 2. del: Zahteve za buldožerje
Earth-moving machinery - Safety - Part 2: Requirements for tractor-dozers
Erdbaumaschinen - Sicherheit - Teil 2: Anforderungen für Planiermaschinen
Engins de terrassement - Sécurité - Partie 2: Prescriptions applicables aux bouteurs
Ta slovenski standard je istoveten z: EN 474-2:2006+A1:2008
ICS:
53.100 Stroji za zemeljska dela Earth-moving machinery
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 474-2:2006+A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
October 2008
ICS 53.100 Supersedes EN 474-2:2006
English Version
Earth-moving machinery - Safety - Part 2: Requirements for
tractor-dozers
Engins de terrassement - Sécurité - Partie 2: Prescriptions Erdbaumaschinen - Sicherheit - Teil 2: Anforderungen für
applicables aux bouteurs Planiermaschinen
This European Standard was approved by CEN on 17 April 2006 and includes Amendment 1 approved by CEN on 18 August 2008.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 474-2:2006+A1:2008: E
worldwide for CEN national Members.
Contents Page
Foreword.3
Introduction .5
1 Scope .6
2 Normative references .6
3 Terms and definitions .6
4 List of additional significant hazards .7
5 Safety requirements and/or measures .7
5.1 General.7
5.2 Operator’s seat.7
5.3 Rear window(s) .7
5.4 Rear-mounted winch .8
6 Information for use .8
6.1 Warning signs .8
6.2 Operation manual .8
6.3 Machine marking.8
Annex A (normative) List of additional significant hazards – Tractor-dozers.9
Annex B (informative) Illustrations.10
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 98/37/EC .12
Annex ZB (informative) !!!!Relationship between this European Standard and the Essential
Requirements of EU Directive 2006/42/EC"""".13
Bibliography .14
Figures
Figure B.1 — Crawler tractor-dozer . 10
Figure B.2 — Wheel tractor-dozer. 10
Figure B.3 — Crawler tractor-dozer with a plough. 11
Tables
Table A.1 — List of additional significant hazards. 9
Foreword
This document (EN 474-2:2006+A1:2008) has been prepared by Technical Committee CEN/TC 151
“Construction equipment and building material machines — Safety”, the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by April 2009, and conflicting national standards shall be withdrawn at the
latest by December 2009.
This European Standard supersedes !EN 474-2:2006".
This document includes Amendment 1, approved by CEN on 2008-08-18.
The start and finish of text introduced or altered by amendment is indicated in the text by tags ! "
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive.
!For relationship with EU Directive(s), see informative Annexes ZA and ZB, which are integral parts of this
document."
For bibliographic references see EN 474-1:2006.
EN 474 "Earth-moving machinery — Safety" comprises the following parts:
Part 1: General requirements
Part 2: Requirements for tractor-dozers
Part 3: Requirements for loaders
Part 4: Requirements for backhoe-loaders
Part 5: Requirements for hydraulic excavators
Part 6: Requirements for dumpers
Part 7: Requirements for scrapers
Part 8: Requirements for graders
Part 9: Requirements for pipelayers
Part 10: Requirements for trenchers
Part 11: Requirements for earth and landfill compactors
Part 12: Requirements for cable excavators
This European Standard is intended for use in combination with Part 1 of the series.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and United Kingdom.
Introduction
This part of EN 474 is a type C standard as stated in EN ISO 12100-1:2003.
The machinery concerned and the extent to which hazards, hazardous situations and events are covered are
indicated in the scope of this European Standard.
When provisions of this type C standard are different from those which are stated in type A or B standards, the
provisions of this type C standard take precedence over the provisions of the other standards, for machines
that have been designed and built according to the provisions of this type C standard.
1 Scope
This part of EN 474 deals with all significant hazards, hazardous situations and events relevant to wheel and
crawler tractor-dozers as defined in EN ISO 6165:2006, when they are used as intended and under conditions
of misuse which are reasonably foreseeable by the manufacturer (see Clause 4).
This part also deals with rear-mounted winches for use on tractor-dozers.
The requirements of this part are complementary to the common requirements formulated in EN 474-1:2006.
This part does not repeat the requirements from EN 474-
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.