EN ISO 15874-3:2003/FprA1
(Amendment)Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 3: Fittings - Amendment 1 (ISO 15874-3:2003/FDAM 1:2009)
Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 3: Fittings - Amendment 1 (ISO 15874-3:2003/FDAM 1:2009)
This Part of EN ISO 15874 specifies the characteristics of fittings for polypropylene (PP) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems under design pressures and temperatures according to the class of application (see Table 1 of EN ISO 15874-1:2003).
This standard covers a range of service conditions (application classes) and design pressure classes. For values of TD, Tmax and Tmal in excess of those in Table 1of Part 1, this standard does not apply.
NOTE It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
It also specifies the parameters for the test methods referred to in this standard.
In conjunction with the other parts of EN ISO 15874 (see Foreword) it is applicable to fittings made from PP and to fittings made from other materials which are intended to be fitted to pipes conforming to EN ISO 15874-2 for hot and cold water installations and whereby the joints conform to the requirements of EN ISO 15874-5.
It is also applicable to fittings made from alternative materials which when fitted to pipes conforming to Part 2, conform to the requirements of Part 5 of EN ISO 15874.
This standard is applicable to fittings of the following types:
socket fusion fittings
electrofusion fittings
mechanical fittings
fittings with incorporated inserts
Kunststoff-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation - Polypropylen (PP) - Teil 3: Formstücke (Änderung von ISO 15874-3:2003) (ISO 15874-3:2003/FDAM 1:2009)
Systèmes de canalisations en plastique pour les installations d'eau chaude et froide - Polypropylène (PP) - Partie 3: Raccords - Amendement 1 (ISO 15874-3:2003/FDAM 1:2009)
Cevni sistemi iz polimernih materialov za napeljave z vročo in hladno vodo - Polipropilen (PP) - 3. del: Fitingi - Dopolnilo 1 (ISO 15874-3:2003/FDAM 1:2009)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-junij-2009
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORY]DQDSHOMDYH]YURþRLQKODGQRYRGR
3ROLSURSLOHQ 33 GHO )LWLQJL'RSROQLOR ,62 )'$0
Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 3:
Fittings - Amendment 1 (ISO 15874-3:2003/FDAM 1:2009)
Kunststoff-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation - Polypropylen
(PP) - Teil 3: Formstücke (Änderung von ISO 15874-3:2003) (ISO 15874-3:2003/FDAM
1:2009)
Systèmes de canalisations en plastique pour les installations d'eau chaude et froide -
Polypropylène (PP) - Partie 3: Raccords - Amendement 1 (ISO 15874-3:2003/FDAM
1:2009)
Ta slovenski standard je istoveten z: EN ISO 15874-3:2003/FprA1
ICS:
23.040.45 Fitingi iz polimernih Plastics fittings
materialov
91.140.60 Sistemi za oskrbo z vodo Water supply systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
FINAL DRAFT
EN ISO 15874-3:2003
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA1
March 2009
ICS 23.040.45; 91.140.60
English Version
Plastics piping systems for hot and cold water installations -
Polypropylene (PP) - Part 3: Fittings - Amendment 1 (ISO
15874-3:2003/FDAM 1:2009)
Systèmes de canalisations en plastique pour les
installations d'eau chaude et froide - Polypropylène (PP) -
Partie 3: Raccords - Amendement 1 (ISO 15874-
3:2003/FDAM 1:2009)
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 155.
This draft amendment A1, if approved, will modify the European Standard EN ISO 15874-3:2003. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15874-3:2003/FprA1:2009: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Foreword
This document (EN ISO 15874-3:2003/FprA1:2009) has been prepared by Technical Committee CEN/TC 155
“Plastics piping systems and ducting systems", the secretariat of which is held by NEN, in collaboration with
Technical Committee ISO/TC 138 "Plastics pipes, fittings and valves for the transport of fluids".
This document is currently submitted to the Unique Acceptance Procedure.
FINAL ISO
AMENDMENT
DRAFT 15874-3:2003
FDAM 1
ISO/TC 138/SC 2
Plastics piping systems for hot and cold
Secretariat: SNV
water installations —
Voting begins on:
Polypropylene (PP) —
2009-03-26
Part 3:
Voting terminates on:
2009-05-26
Fittings
AMENDMENT 1
Systèmes de canalisations en plastique pour les installations d'eau
chaude et froide — Polypropylène (PP) —
Partie 3: Raccords
AMENDEMENT 1
Please see the administrative notes on page iii
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPORT-
ING DOCUMENTATION.
IN ADDITION TO THEIR EVALUATION AS
Reference number
BEING ACCEPTABLE FOR INDUSTRIAL, TECHNO-
ISO 15874-3:2003/FDAM 1:2009(E)
LOGICAL, COMMERCIAL AND USER PURPOSES,
DRAFT INTERNATIONAL STANDARDS MAY ON
OCCASION HAVE TO BE CONSIDERED IN THE
LIGHT OF THEIR POTENTIAL TO BECOME STAN-
DARDS TO WHICH REFERENCE MAY BE MADE IN
©
NATIONAL REGULATIONS. ISO 2009
ISO 15874-3:2003/FDAM 1:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted
under the applicable laws of the user's country, neither this ISO draft nor any extract from it may be
reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic,
photocopying, recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO's
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.