CEN/TC 155/WG 16 - Systems for hot and cold water applications

This document gives requirements and guidance for the assessment of conformity of compounds, products, and assemblies in accordance with the applicable part(s) of ISO 21003 intended to be included in the manufacturer's quality plan as part of the quality management system and for the establishment of certification procedures.
In conjunction with the other parts of ISO 21003 (see Foreword), this document is applicable to multilayer piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures appropriate to the class of application (see ISO 21003-1:2008, Table 1).

This document gives requirements and guidance for the assessment of conformity of compounds, products, and assemblies in accordance with the applicable part(s) of ISO 15875 intended to be included in the manufacturer's quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE       In order to help the reader, a basic test matrix is given in Annex A.
In conjunction with the other parts of ISO 15875 (see Foreword), this document is applicable to crosslinked polyethylene (PE-X) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures appropriate to the class of application (see ISO 15875-1:2003, Table 1).

This document gives requirements and guidance for the assessment of conformity of compounds, products, and assemblies in accordance with the applicable part(s) of ISO 15876 intended to be included in the manufacturer's quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE       In order to help the reader, a basic test matrix is given in Annex A.
In conjunction with the other parts of ISO 15876 (see Foreword), this document is applicable to polybutene (PB) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures appropriate to the class of application (see ISO 15876-1:2017, Table 1).

This document gives requirements and guidance for the assessment of conformity of compounds, products, and assemblies in accordance with the applicable part(s) of ISO 15874 intended to be included in the manufacturer's quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE       In order to help the reader, a basic test matrix is given in Annex A.
In conjunction with the other parts of ISO 15874 (see Foreword), this document is applicable to polypropylene (PP) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures appropriate to the class of application (see ISO 15874-1:2013, Table 1).

This part of ISO 15877 gives guidance for the assessment of conformity of materials, products, and assemblies in accordance with the applicable part(s) of ISO 15877 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of  certification procedures.
In conjunction with the other parts of ISO 15877 (see Foreword), this Technical Specification (International Standard) is applicable to Chlorinated poly(vinyl chloride) (PVC-C) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures appropriate to the class of application (see Table 1 of ISO 15877-1:2009).

This part of ISO 22391 gives guidance for the assessment of conformity of materials, products, and assemblies in accordance with the applicable part(s) of ISO 22391 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
In conjunction with the other parts of ISO 22391 (see Foreword), this Technical Specification is applicable to polyethylene of raised temperature resistance (PE-RT) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures appropriate to the class of application (see Table 1 of ISO 22391:2009).

ISO 15876-5:2017 specifies the characteristics of the fitness for purpose of polybutene-1 (PB-1) piping systems, intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption, (domestic systems) and for heating systems, under design pressures and temperatures according to the class of application (see ISO 15876‑1).
The designation polybutene is used together with the abbreviation PB throughout this document.
ISO 15876-5:2017 covers a range of service conditions (application classes) and design pressure classes. For values of TD, Tmax and Tmal in excess of those in ISO 15876‑1:2016, Table 1, this document does not apply.
NOTE          It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
It also specifies the test parameters for the test methods referred to in this document.
In conjunction with the other parts of ISO 15876, it is applicable to PB pipes, fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for hot and cold water installations.

ISO 15876-2:2017 specifies the characteristics of pipes for polybutene-1 (PB-1) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water whether or not intended for human consumption (domestic systems), and for heating systems, under design pressures and temperatures appropriate to the class of application (see ISO 15876‑1).
The designation polybutene is used together with the abbreviation PB throughout this document.
ISO 15876-2:2017 covers a range of service conditions (application classes), design pressures and pipe dimension classes. For values of TD, Tmax and Tmal in excess of those in ISO 15876‑1, this document does not apply.
NOTE 1       It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
It also specifies the test parameters for the test methods referred to in this document.
In conjunction with the other parts of ISO 15876, this document is applicable to PB pipes, their joints and to joints with components of PB, other plastics and non-plastics materials intended to be used for hot and cold water installations.
It is applicable to pipes with or without (a) barrier layer(s).
NOTE 2       In the case of plastics pipes provided with a thin barrier layer, e.g. to prevent or greatly diminish the diffusion of gases and the transmission of light into or through the pipe wall, the design stress requirements are totally met by the base polymer (PB).

ISO 15876-1:2017 specifies the general aspects of polybutene-1 (PB-1) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures according to the class of application (see Table 1).
The designation polybutene is used together with the abbreviation PB throughout this document.
ISO 15876-1:2017 covers a range of service conditions (application classes) and design pressure and pipe dimension classes. Values of TD, Tmax and Tmal in excess of those in Table 1 do not apply.
NOTE          It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
It also specifies the test parameters for the test methods referred to in this document.
In conjunction with the other parts of ISO 15876, this document is applicable to PB pipes, fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for hot and cold water installations.

ISO 15876-3:2017 specifies the characteristics of fittings for polybutene-1 (PB-1) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems under design pressures and temperatures according to the class of application (see ISO 15876‑1).
The designation polybutene is used together with the abbreviation PB throughout this document.
ISO 15876-3:2017 covers a range of service conditions (application classes) and design pressure classes. For values of TD, Tmax and Tmal in excess of those in ISO 15876‑1:2016, Table 1, this document does not apply.
NOTE          It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
It also specifies the parameters for the test methods referred to in this document.
In conjunction with the other parts of ISO 15876, this document is applicable to fittings made from PB and to fittings made from other materials which are intended to be fitted to pipes conforming to ISO 15876‑2 for hot and cold water installations, whereby the joints conform to the requirements of ISO 15876‑5.
ISO 15876-3:2017 is applicable to fittings of the following types:
-      socket fusion fittings;
-      electrofusion fittings;
-      mechanical fittings;
-      fittings with incorporated inserts.
It is also applicable to fittings made from alternative materials which, when fitted to pipes conforming to ISO 15876‑2, conform to the requirements of ISO 15876‑5.

ISO 15874-1:2013 specifies the general aspects of polypropylene (PP) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water whether or not intended for human consumption (domestic systems), and for heating systems, under design pressures and temperatures according to the class of application.
It covers a range of service conditions (classes of application), design pressures and pipe dimension classes.
It also specifies test parameters for test methods.
In conjunction with the other parts of ISO 15874, ISO 15874-1:2013 is applicable to PP pipes, fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for hot and cold water installations.

ISO 15874-2:2013 specifies the requirements of pipes made from polypropylene (PP) for piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water whether or not intended for human consumption (domestic systems) and for heating systems under operating pressures and temperatures appropriate to the class of application.
It covers a range of service conditions (application classes), design pressures and pipe dimension classes.
It also specifies test parameters for test methods.
In conjunction with the other parts of ISO 15874, ISO 15874-2:2013 is applicable to PP pipes, their joints and to joints with components of PP, other plastics and non-plastics materials intended to be used for hot and cold water installations.
It is applicable to pipes with or without (a) barrier layer(s).

This Part of EN ISO 15874 specifies the characteristics of fittings for polypropylene (PP) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems under design pressures and temperatures according to the class of application (see Table 1 of EN ISO 15874-1:2003).
This standard covers a range of service conditions (application classes) and design pressure classes. For values of TD, Tmax and Tmal in excess of those in Table 1of Part 1, this standard does not apply.
NOTE It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
It also specifies the parameters for the test methods referred to in this standard.
In conjunction with the other parts of EN ISO 15874 (see Foreword) it is applicable to fittings made from PP and to fittings made from other materials which are intended to be fitted to pipes conforming to EN ISO 15874-2 for hot and cold water installations and whereby the joints conform to the requirements of EN ISO 15874-5.
It is also applicable to fittings made from alternative materials which when fitted to pipes conforming to Part 2, conform to the requirements of Part 5 of EN ISO 15874.
This standard is applicable to fittings of the following types:
- socket fusion fittings
- electrofusion fittings
- mechanical fittings
- fittings with incorporated inserts

ISO 15874-5:2013 specifies the characteristics of the fitness for purpose of polypropylene (PP) piping systems, intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures according to the class of application.
It covers a range of service conditions (classes of application) and design pressure classes.
It also specifies test parameters for test methods.
In conjunction with the other parts of ISO 15874, it is applicable to PP pipes, fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for hot and cold water installations.

This European Technical Report recommends practices to be followed in the application and installation of thermoplastics pipes and associated fittings. These fall within the scope of EN 806-1 and, EN ISO 15874, EN ISO 15875, EN ISO 15876, EN ISO 15877 and EN ISO 22391 to be used for hot and/or cold water distribution intended for human consumption inside buildings. This document can also be used for heating installations if applicable, except for under floor heating for which EN 12164 can apply.
Guidance is also given on acceptable methods of jointing polybutylene (PB), crosslinked polyethylene (PE X), polypropylene (PP), chlorinated poly(vinyl chloride) (PVC-C) and Polyethylene of raised temperature resistance (PE-RT) pipes and associated fittings, together with recommendations for their storage, handling and transportation.

2010-08-31 EMA: Final draft received in ISO/CS following notification received in dataservice on 2010-08-31.

2009-04-02 EMA: VA information and track changed from ISO Lead to CEN Lead after ISO notification (see e-mail sent on 2009-04-01).

2009-04-02 EMA: VA information and track changed from ISO Lead to CEN Lead after ISO notification (see e-mail sent on 2009-04-01).

2009-04-02 EMA: VA information and track changed from ISO Lead to CEN Lead after ISO notification (see e-mail sent on 2009-04-01).

2009-04-02 EMA: VA information and track changed from ISO Lead to CEN Lead after ISO notification (see e-mail sent on 2009-04-01).

ISO 15877-2:2009 specifies the requirements of pipes made from chlorinated poly(vinyl chloride) (PVC-C) for piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures appropriate to the class of application.
ISO 15877-2:2009 covers a range of service conditions (application classes), design pressures and pipe series. It does not apply if the values of the design temperature, maximum design temperature and malfunction temperature are in excess of those given in ISO 15877-1:2009. ISO 15877-2:2009 also specifies the test parameters for the test methods to which it refers.
In conjunction with the other parts of ISO 15877, it is applicable to PVC-C pipes, their joints and joints with components of PVC-C, other plastics and non-plastics materials intended to be used for hot and cold water installations.

ISO 15877-3:2009 specifies the characteristics of fittings made from chlorinated poly(vinyl chloride) (PVC-C) for piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems under design pressures and temperatures according to the class of application.
ISO 15877-3:2009 covers a range of service conditions (application classes) and design pressure classes. It does not apply if the values of the design temperature, maximum design temperature and malfunction temperature are in excess of those given in ISO 15877-1:2009. ISO 15877-3:2009 also specifies the parameters for the test methods to which it refers.
In conjunction with the other parts of ISO 15877, it is applicable to PVC-C fittings, their joints and joints with components of PVC-C, other plastics and non-plastics materials intended to be used for hot and cold water installations.
It is applicable to fittings of the following types:
fittings for solvent cement joints;
mechanical fittings;
fittings with incorporated inserts.

ISO 15877-5:2009 specifies the characteristics of the fitness for purpose of chlorinated poly(vinyl chloride) (PVC-C) piping systems, intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption, (domestic systems) and for heating systems, under design pressures and temperatures according to the class of application.
ISO 15877-5:2009 covers a range of service conditions (application classes) and design pressure classes. It does not apply if the values of the design temperature, maximum design temperature and malfunction temperature are in excess of those given in ISO 15877-1:2009. ISO 15877-5:2009 specifies the test parameters for the test methods to which it refers.
In conjunction with the other parts of ISO 15877, it is applicable to PVC-C pipes and fittings, their joints and joints with components of other plastics and non-plastics materials intended to be used for hot and cold water installations.

ISO 15877-1:2009 specifies the general requirements of chlorinated poly(vinyl chloride) (PVC-C) piping systems intended to be used for hot and cold water installations within buildings for the conveyance of water, whether or not intended for human consumption (domestic systems) and for heating systems, under design pressures and temperatures appropriate to the class of application.
It covers a range of service conditions (classes of application), design pressures and pipe dimension classes. It does not apply if the values of the design temperature, maximum design temperature and malfunction temperature are in excess of those given. ISO 15877-1:2009 also specifies the test parameters for the test methods to which it refers.
In conjunction with the other parts of ISO 15877, it is applicable to PVC-C pipes and fittings, their joints and joints with components of other plastics and non-plastics materials intended to be used for hot and cold water installations.

ISO 21003-5:2008 specifies the characteristics for the fitness for purpose of multilayer piping systems intended to be used for hot and cold water installations inside buildings for the conveyance of water — whether or not the water is intended for human consumption (domestic systems) or for heating systems — under specified design pressures and temperatures appropriate to the class of application.
It also specifies the test parameters for the test methods referred to in this part of ISO 21003.
ISO 21003 is a reference product standard. It is applicable to multilayer pipes, fittings, their joints, and also to joints with components made of other plastics and non-plastics materials intended to be used for hot and cold water installations. ISO 21003-5 is intended for use only in conjunction with all the other parts of ISO 21003.

ISO 21003-3:2008 specifies the characteristics of fittings for multilayer piping systems intended to be used for hot and cold water installations inside buildings for the conveyance of water — whether or not the water is intended for human consumption (domestic systems) or for heating systems — under specified design pressures and temperatures appropriate to the class of application
It also specifies the test parameters for the test methods referred to in this part of ISO 21003.
ISO 21003 is a reference product standard. It is applicable to multilayer pipes, fittings, their joints, and also to joints with components made of other plastics and non-plastics materials intended to be used for hot and cold water installations. ISO 21003-3 is intended for use only in conjunction with all the other parts of ISO 21003.

ISO 21003-1:2008 specifies the general aspects of multilayer piping systems intended to be used for hot and cold water installations inside buildings for the conveyance of water — whether or not the water is intended for human consumption (domestic systems) or heating systems — under specified design pressures and temperatures appropriate to the class of application.
ISO 21003 is a reference product standard. It is applicable to multilayer pipes, fittings, their joints, and also to joints with components made of other plastics and non-plastics materials intended to be used for hot and cold water installations. ISO 23001-1 is intended for use only in conjunction with all the other parts of ISO 21003.

ISO 21003-2:2008 specifies the characteristics of pipes for multilayer piping systems intended to be used for hot and cold water installations inside buildings for the conveyance of water — whether or not the water is intended for human consumption (domestic systems) or heating systems — under specified design pressures and temperatures appropriate to the class of application.
It also specifies the test parameters for the test methods referred to in this part of ISO 21003.
ISO 21003 is a reference product standard. It is applicable to multilayer pipes, fittings, their joints, and also to joints with components made of other plastics and non-plastics materials intended to be used for hot and cold water installations. ISO 21003-2 is intended for use only in conjunction with all the other parts of ISO 21003.