Aluminium and aluminium alloys - Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 - Part 1: Technical conditions for inspection and delivery

This document specifies technical conditions for inspection and delivery of alloys EN AW-6060 and EN AW-6063 extruded precision profiles manufactured with and without a thermal barrier (see Figures 1 and 2) and without further surface treatment.
Precision profiles covered in this document are distinguished from extruded profiles for general applications covered in EN 755-9 by the following characteristics:
   they are mainly for architectural applications;
   they meet more stringent requirements regarding the surface condition of visible surfaces;
    the maximum diameter of the circumscribing circle CD is 350 mm;
   they are made to closer tolerances on dimensions and form.
In the case of profiles, which, due to the complexity of their design are difficult to manufacture and specify, then special agreements between supplier and purchaser may need to be reached.
NOTE   The effect of the thermal barrier material on the dimensional tolerances is covered by EN 12020-2 although the actual thermal barrier material itself is not (see EN 14024).

Aluminium und Aluminiumlegierungen - Stranggepresste Präzisionsprofile aus Legierungen EN AW-6060 und EN AW-6063 - Teil 1: Technische Lieferbedingungen

Dieses Dokument legt die Technischen Lieferbedingungen für stranggepresste Präzisionsprofile aus den Legierungen EN AW-6060 und EN AW-6063, die mit oder ohne Wärmedämmung (siehe Bild 1 und Bild 2) hergestellt werden, fest. Es gilt für stranggepresste Erzeugnisse, die ohne weitere Oberflächenbehandlung geliefert werden.
Die Präzisionsprofile, die Gegenstand dieses Dokuments sind, unterscheiden sich von den stranggepressten Profilen für allgemeine Anwendungen nach EN 755 9 wie folgt:
   sie sind hauptsächlich für Anwendungen im Architekturbereich vorgesehen;
   sie entsprechen strengeren Anforderungen im Hinblick auf den Zustand der sichtbaren Oberflächen;
   der maximale Durchmesser des Umschlingungskreises CD beträgt 350 mm;
   sie weisen engere Grenzabmaße und Formtoleranzen auf.
Bei Profilen, die aufgrund ihrer komplexen Konstruktion schwierig herzustellen und zu spezifizieren sind, können besondere Vereinbarungen zwischen Lieferer und Käufer notwendig sein.
ANMERKUNG   Der Einfluss des Materials für die Wärmedämmung auf die Grenzabmaße wird in prEN 12020 2 berücksichtigt, wenngleich das eigentliche Material für die Wärmedämmung nicht enthalten ist (siehe EN 14024).

Aluminium et alliages d'aluminium - Profilés de précision filés en alliages EN AW-6060 et EN AW-6063 - Partie 1: Conditions techniques de contrôle et de livraison

Le présent document spécifie les conditions techniques de contrôle et de livraison des profilés filés de précision en alliages EN AW-6060 et EN AW-6063 fabriqués avec ou sans barrière thermique (voir Figures 1 et 2) et sans autre traitement de surface.
Les profilés de précision couverts dans cette norme se distinguent des produits filés pour application générale couverts dans l’EN 755-9 par les caractéristiques suivantes :
   ils sont principalement destinés aux applications architecturales ;
   ils répondent à des exigences plus rigoureuses en ce qui concerne l’état de surface des surfaces visibles ;
   le diamètre maximum du cercle circonscrit CD est de 350 mm ;
   ils sont fabriqués avec des tolérances sur dimensions et forme plus serrées.
Dans le cas de profilés, lesquels qui, en raison de la complexité de leur conception, sont difficiles à spécifier et à fabriquer, des accords spéciaux entre acheteur et fabriquant sont à trouver.
NOTE   Les effets du matériau de la barrière thermique sur les tolérances dimensionnelles sont couverts par l’EN 12020-2 même si le matériau de la barrière thermique lui-même ne l’est pas (voir l’EN 14024).

Aluminij in aluminijeve zlitine - Precizni iztiskani profili v zlitinah EN AW-6060 in EN AW-6063 - 1. del: Tehnični pogoji za pregled in dobavo

General Information

Status
Withdrawn
Publication Date
18-Mar-2008
Withdrawal Date
22-Mar-2022
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
23-Mar-2022

Relations

Buy Standard

Standard
EN 12020-1:2008
English language
11 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aluminium and aluminium alloys - Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 - Part 1: Technical conditions for inspection and deliveryAluminium et alliages d'aluminium - Profilés de précision filés en alliages EN AW-6060 et EN AW-6063 - Partie 1: Conditions techniques de contrôle et de livraisonAluminium und Aluminiumlegierungen - Stranggepresste Präzisionsprofile aus Legierungen EN AW-6060 und EN AW-6063 - Teil 1: Technische LieferbedingungenTa slovenski standard je istoveten z:EN 12020-1:2008SIST EN 12020-1:2008en77.150.10ICS:SIST EN 12020-1:2002/AC:2004SIST EN 12020-1:20021DGRPHãþDSLOVENSKI
STANDARDSIST EN 12020-1:200801-maj-2008







EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 12020-1March 2008ICS 77.150.10Supersedes EN 12020-1:2001
English VersionAluminium and aluminium alloys - Extruded precision profiles inalloys EN AW-6060 and EN AW-6063 - Part 1: Technicalconditions for inspection and deliveryAluminium et alliages d'aluminium - Profilés de précisionfilés en alliages EN AW-6060 et EN AW-6063 - Partie 1:Conditions techniques de contrôle et de livraisonAluminium und Aluminiumlegierungen - StranggepresstePräzisionsprofile aus Legierungen EN AW-6060 und ENAW-6063 - Teil 1: Technische LieferbedingungenThis European Standard was approved by CEN on 10 February 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12020-1:2008: E



EN 12020-1:2008 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.5 3 Terms and definitions.5 4 Ordering information.6 4.1 General.6 4.2 Reference to a drawing.7 5 Requirements.7 5.1 Production and manufacturing processes.7 5.2 Quality control.8 5.3 Chemical composition limit.8 5.4 Mechanical properties.8 5.5 Freedom from surface defects.8 5.6 Tolerances on dimensions and form.8 5.7 Section mass.8 6 Test procedures.8 6.1 Sampling.8 6.2 Test methods.9 7 Inspection documents.9 8 Marking of products.9 9 Packaging.10 10 Arbitration.10 Bibliography.11



EN 12020-1:2008 (E) 3 Foreword This document (EN 12020-1:2008) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by September 2008, and conflicting national standards shall be withdrawn at the latest by September 2008. This document supersedes EN 12020-1:2001. Within its programme of work, Technical committee CEN/TC 132 entrusted CEN/TC 132/WG 5 "Extruded and drawn products" to revise EN 12020-1:2001 The following technical modifications have been introduced during the revision:  Clause 3: Definition of "order document" is included  Subclause 4.2: An additional Figure 3 is included identifying visible surfaces and weld lines  Subclause 5.5: Requirements to streaks and surface texture appearance on visible surfaces in mill finish are included  Subclause 5.7: Requirements to tolerance on mass are included EN 12020 comprises the following parts under the general title "Aluminium and aluminium alloys — Extruded precision profiles in alloys EN AW-6060 and EN AW-6063":  Part 1: Technical conditions for inspection and delivery  Part 2: Tolerances on dimensions and form Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. CEN/TC 132 affirms it is its policy that in the case when a patentee refuses to grant licenses on standardized standards products under reasonable and not discriminatory conditions then this product shall be removed from the corresponding standard. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.



EN 12020-1:2008 (E) 4 1 Scope This document specifies technical conditions for inspection and delivery of alloys EN AW-6060 and EN AW-6063 extruded precision profiles manufactured with and without a thermal barrier (see Figures 1 and 2) and without further surface treatment. Precision profiles covered in this document are distinguished from extruded profiles for general applications covered in EN 755-9 by the following characteristics:  they are mainly for architectural applications;  they meet more stringent requirements regarding the surface condition of visible surfaces;

the maximum diameter of the circumscribing circle CD is 350 mm;  they are made to closer tolerances on dimensions and form. In the case of profiles, which, due to the complexity of their design are difficult to manufacture and specify, then special agreements between supplier and purchaser may need to be reached. NOTE The effect of the thermal barrier material on the dimensional tolerances is covered by EN 12020-2 although the actual thermal barrier material itself is not (see EN 14024).
Key 1 CD maximum 350 mm
Key 1 CD maximum 350 mm
2 thermal barriers Figure 1 — Profile without thermal barrier Figure 2 — Profile containing thermal barrier



EN 12020-1:2008 (E) 5 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references only the edition cited applies. For undated references the latest edition of the referenced document (including any amendments) applies. EN 515, Aluminium and aluminium alloys — Wrought products — Temper designations EN 573-3, Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products EN 755-1, Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles — Part 1: Technical conditions for inspection and delivery EN 755-2, Aluminium and aluminium alloys — Extruded rod/bar, tube and profiles — Part 2: Mechanical properties EN 10002-1, Metallic materials — Tensile testing — Part 1: Method of test at ambient temperature
EN 10204, Metallic products — Types of inspection documents EN 12020-2, Aluminium and alumin
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.