prEN ISO 374-6
(Main)Protective gloves against dangerous chemicals and micro-organisms - Part 6: Protective gloves for hairdressers (ISO/DIS 374-6:2023)
Protective gloves against dangerous chemicals and micro-organisms - Part 6: Protective gloves for hairdressers (ISO/DIS 374-6:2023)
This document specifies the requirements for protective gloves to protect the hairdressers, especially the risk against micro-organisms and dangerous chemicals, and defines terms to be used.
Schutzhandschuhe gegen gefährliche Chemikalien und Mikroorganismen - Teil 6: Schutzhandschuhe für Friseure (ISO/DIS 374 6:2023)
Gants de protection contre les produits chimiques dangereux et les micro-organismes - Partie 6: Gants de protection pour les coiffeurs (ISO/DIS 374-6:2023)
Varovalne rokavice za zaščito pred nevarnimi kemikalijami in mikroorganizmi - 6. del: Zaščitne rokavice za frizerje (ISO/DIS 374-6:2023)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2023
Varovalne rokavice za zaščito pred nevarnimi kemikalijami in mikroorganizmi - 6.
del: Zaščitne rokavice za frizerje (ISO/DIS 374-6:2023)
Protective gloves against dangerous chemicals and micro-organisms - Part 6: Protective
gloves for hairdressers (ISO/DIS 374-6:2023)
Schutzhandschuhe gegen gefährliche Chemikalien und Mikroorganismen - Teil 6:
Schutzhandschuhe für Friseure (ISO/DIS 374 6:2023)
Gants de protection contre les produits chimiques dangereux et les micro-organismes -
Partie 6: Gants de protection pour les coiffeurs (ISO/DIS 374-6:2023)
Ta slovenski standard je istoveten z: prEN ISO 374-6
ICS:
13.340.40 Varovanje dlani in rok Hand and arm protection
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT INTERNATIONAL STANDARD
ISO/DIS 374-6
ISO/TC 94/SC 13 Secretariat: SNV
Voting begins on: Voting terminates on:
2023-04-20 2023-07-13
Protective gloves against dangerous chemicals and micro-
organisms —
Part 6:
Protective gloves for hairdressers
Gants de protection contre les produits chimiques dangereux et les micro-organismes —
Partie 6: Gants de protection pour les coiffeurs
ICS: 13.340.40
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 374-6:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023
ISO/DIS 374-6:2023(E)
DRAFT INTERNATIONAL STANDARD
ISO/DIS 374-6
ISO/TC 94/SC 13 Secretariat: SNV
Voting begins on: Voting terminates on:
Protective gloves against dangerous chemicals and micro-
organisms —
Part 6:
Protective gloves for hairdressers
Gants de protection contre les produits chimiques dangereux et les micro-organismes —
Partie 6: Gants de protection pour les coiffeurs
ICS: 13.340.40
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2023
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
NOT BE REFERRED TO AS AN INTERNATIONAL
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
IN ADDITION TO THEIR EVALUATION AS
or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: +41 22 749 01 11
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: copyright@iso.org
NATIONAL REGULATIONS.
Website: www.iso.org ISO/DIS 374-6:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
ii
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023
ISO/DIS 374-6:2023(E)
Contents Page
European foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Performance requirement.2
4.1 General requirements . 2
4.2 Glove's length . 2
4.3 Mechanical strength . 3
4.4 Resistance to microorganisms . 3
4.5 Permeation . 3
5 Test methods . 4
5.1 Mechanical strength . 4
5.1.1 Conditioning . 4
5.1.2 Sampling . 4
5.1.3 Test method for mechanical strength . 5
5.2 Permeation test . 6
5.2.1 Conditioning . 6
5.2.2 Test procedure. 6
6 Marking . . 7
7 Information supplied by the manufacturer . 7
Annex ZA (informative) Relationship between this European Standard and Essential
Requirements of Regulation 2016/425 aimed to be covered . 9
iii
ISO/DIS 374-6:2023(E)
European foreword
This document (prEN ISO 374-6:2023) has been prepared by Technical Committee CEN/TC 162
“Protective clothing including hand and arm protection and lifejackets", the secretariat of which is held
by DIN, in collaboration with Technical Committee ISO/TC 94 "Personal safety - Protective clothing and
equipment".
This document is currently submitted to the CEN Enquiry.
This document has been prepared under the Standardization Request M/571 given to CEN by the
European Commission and the European Free Trade Association and supports essential requirements
of Regulation (EU) 2016/425.
For relationship with EU Regulation (EU) 2016/425, see Annex ZA, which is an integral part of this
document.
iv
DRAFT INTERNATIONAL STANDARD ISO/DIS 374-6:2023(E)
Protective gloves against dangerous chemicals and micro-
organisms —
Part 6:
Protective gloves for hairdressers
1 Scope
This standard specifies the requirements for protective gloves to protect the hairdressers especially
the risk against micro-organisms and dangerous chemicals and defines terms to be used.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN ISO 374-1+A1: 2018, Protective gloves against chemicals and micro-organisms — Part 1 terminology
and performance requirements for chemical risks
EN ISO 374-2:2019, Protective gloves against chemicals and micro-organisms — Part 2: Determination of
resistance to penetration
EN ISO 374-5:2016, Protective gloves against dangerous chemicals and micro-organisms — terminology
and performance requirements for micro-organisms risks
EN ISO 6529:2013, Protective clothing - Protection against chemicals - Determination of resistance of
protective clothing materials to permeation by liquids and gases
EN ISO 21171:2006, Medical gloves - Determination of removable surface powder
EN ISO 21420:2019, Protective gloves - General requirements and test methods
EN ISO 23529:2010, Rubber - General procedures for preparing and conditioning test pieces for physical
test methods
E N 16523-1+A 1: 2018 , Determination of material resistance to permeation by chemicals - Part 1:
Permeation by liquid chemical under conditions of continuous contact
3 Terms and definitions
For the purposes of this document, the terms and definitions in EN 16523-1+A1: 2018, EN ISO 374-1 and
EN ISO 374-5 and the following apply.
3.1
gloves for hairdressers
gloves to protect the skin of the hairdresser during the handling of chemicals and the use of water
during his/her work (coloring, discoloring, curling, washing…)
3.2
protective glove material
any material or combination of materials used in a protective glove for the purpose of isolating the
hands or hands and arms from direct contact with a dangerous chemical
ISO/DIS 374-6:2023(E)
3.3
degradation
deleterious change in one or more properties of a protective glove material (3.2) due to contact with a
chemical
Note 1 to entry: Indications of degradation may include flaking, swelling, disintegration, embrittlement, colour
change, dimensional change, appearance, hardening, softening, etc.
3.4
permeation
process by which a chemical moves through a protective glove material (3.2) on a molecular level
Note 1 to entry: Permeation involves the following:
— absorption of molecules of the chemical into the contacted (outside) surface of a material,
— diffusion of the absorbed molecules in the material,
— desorption of the molecules from the opposite (inside) surface of the material.
3.5
test chemical
chemical substance, or mixture of chemical substances, potentially hazardous to the health that is used
under laboratory test conditions to determine the breakthrough time
3.6
single use glove
glove that is to be used on one individual during a single procedure (one task on one client only) and for
a maximum time of 60min
4 Performance requirement
4.1 General requirements
All tests required in this standard shall be performed on unused gloves unless otherwise specified.
Hairdresser's protective gloves shall meet all the applicable requirements of EN ISO 21420:2020.
Special additional requirements are defined in this document (e.g., minimum length of the gloves).
The gloves for hairdressers are single use gloves and they shall not include seams or be welded.
Dexterity test is not required for hairdresser’s protective gloves, as they are thin single use gloves, they
will always satisfy this property.
The gloves for hairdressers shall be conform to the requirement defined in clause 4.2, 4.3, 4.4 and 4.5.
The gloves shall be powder-free. For powder-free gloves the total quantity of powder residues
determined according to the test method in ISO 21171: 2006, clauses 7 and 9 shall not exceed 2 mg per
glove. Any glove containing more than 2 mg powder is a powdered glove.
4.2 Glove's length
The glove length shall be measured according to EN ISO 21420:2020, 6.1.
The minimum length of the glove depends on the claimed protection area.
For type 240, hand protection only, minimum glove length is 240 mm.
For type 300, hand and forearm protection only, minimum glove length is 300 mm.
ISO/DIS 374-6:2023(E)
4.3 Mechanical strength
The glove shall have a sufficient robustness. Different glove materials require different force at break
requirements to ensure an acceptable performance. Absolute force at break values do not directly
correlate with the in-use performance. Selection of appropriate glove materials for the intended
application shall be part of the risk management process.
When tested according to 5.2, the gloves for hairdressers shall have a force at break in accordance with
the value given in
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.