EN ISO 12402-7:2006/A1:2011
(Amendment)Personal flotation devices - Part 7: Materials and components - Safety requirements and test methods (ISO 12402-7:2006)
Personal flotation devices - Part 7: Materials and components - Safety requirements and test methods (ISO 12402-7:2006)
2010-08-27 - IGNORE NEGATIVE ASSESSMENT - SHOULD NOT HAVE GONE TO CONSULTANT
2010-08-27 EMA: Boxes "Harmonized" and "Candidate for citation" unflagged for all directive following e-mail from PM sent to dataservice on 2010-08-27.
Persönliche Auftriebsmittel - Teil 7: Werkstoffe und Bestandteile - Sicherheitstechnische Anforderungen und Prüfverfahren (ISO 12402-7:2006)
Équipements individuels de flottabilité - Partie 7: Matériaux et composants - Exigences de sécurité et méthodes d'essai (ISO 12402-7:2006)
Osebni plavajoči pripomočki - 7. del: Materiali in sestavni deli - Varnostne zahteve in preskusne metode - Dopolnilo 1 (ISO 12402-7:2006/Amd 1:2011)
Ta del prEN ISO 12402 določa zahteve za izdelavo, delovanje in označevanje materialov in sestavnih delov osebnih plavajočih pripomočkov ter tudi ustrezne preskusne metode.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2011
2VHEQLSODYDMRþLSULSRPRþNLGHO 0DWHULDOLLQVHVWDYQLGHOL9DUQRVWQH]DKWHYH
LQSUHVNXVQHPHWRGH'RSROQLOR ,62 $PG
Personal flotation devices - Part 7: Materials and components - Safety requirements and
test methods - Amendment 1 (ISO 12402-7:2006/Amd 1:2011)
Persönliche Auftriebsmittel - Teil 7: Werkstoffe und Bestandteile - Sicherheitstechnische
Anforderungen und Prüfverfahren - Änderung 1 (ISO 12402-7:2006/Amd 1:2011)
Équipements individuels de flottabilité - Partie 7: Matériaux et composants - Exigences
de sécurité et méthodes d'essai - Amendement 1 (ISO 12402-7:2006/Amd 1:2011)
Ta slovenski standard je istoveten z: EN ISO 12402-7:2006/A1:2011
ICS:
13.340.70 5HãLOQLMRSLþLY]JRQVND Lifejackets, buoyancy aids
SRPDJDODLQSODYDMRþL and floating devices
SULSRPRþNL
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 12402-7:2006/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2011
ICS 13.340.70
English Version
Personal flotation devices - Part 7: Materials and components -
Safety requirements and test methods - Amendment 1 (ISO
12402-7:2006/Amd 1:2011)
Équipements individuels de flottabilité - Partie 7: Matériaux Persönliche Auftriebsmittel - Teil 7: Werkstoffe und
et composants - Exigences de sécurité et méthodes d'essai Bestandteile - Sicherheitstechnische Anforderungen und
- Amendement 1 (ISO 12402-7:2006/Amd 1:2011) Prüfverfahren - Änderung 1 (ISO 12402-7:2006/Amd
1:2011)
This amendment A1 modifies the European Standard EN ISO 12402-7:2006; it was approved by CEN on 29 January 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 12402-7:2006/A1:2011: E
worldwide for CEN national Members.
Contents Page
Foreword .3
Annex ZA (informative) Relationship between this International Standard and the Essential
Requirements of EU Directive 89/686/EEC .4
Foreword
This document (EN ISO 12402-7:2006/A1:2011) has been prepared by Technical Committee ISO/TC 188
"Small craft" in collaboration with Technical Committee CEN/TC 162 “Protective clothing including hand and
arm protection and lifejackets” the secretariat of which is held by DIN.
This Amendment to the European Standard EN ISO 12402-7:2006 shall be given the status of a national
standard, either by publication of an identical text or by endorsement, at the latest by October 2011, and
conflicting national standards shall be withdrawn at the latest by October 2011.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive, see informative Annex ZA, which is an integral part of this document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 12402-7:2006/Amd 1:2011 has been approved by CEN as a EN ISO 12402-7:2006/A1:2011
without any modification.
Annex ZA
(informative)
Relationship between this International Standard and the Essential
Requirements of EU Directive 89/686/EEC
This International Standard has been prepared under a mandate given to CEN by the European Commission
to provide one means of conforming to Essential Requirements of the New Approach Directive 89/686/EEC on
the approximation of the laws of the Member States relating to personal protective equipment.
Once this standard is cited in the Official Journal of the European Union under that Directive and has been
implemented as a national standard in at least one Member State, compliance with the normative clauses of
this standard confers, within the limits of the scope of this standard, a presumption of conformity with the
corresponding Essential Requirements of that Directive and associated EFTA regulations.
WARNING: Other requirements and other EU Directives may be applicable to the products falling within the
scope of this standard.
INTERNATIONAL ISO
STANDARD 12402-7
First edition
2006-11-15
AMENDMENT 1
2011-04-01
Personal flotation devices —
Part 7:
Materials and components — Safety
requirements and test methods
AMENDMENT 1
Équipements individuels de flottabilité —
Partie 7: Matériaux et composants — Exigences de sécurité et
méthodes d'essai
AMENDEMENT 1
Reference number
ISO 12402-7:2006/Amd.1:2011(E)
©
ISO 2011
ISO 12402-7:2006/Amd.1:2011(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2011 – All rights reserved
ISO 12402-7:2006/Amd.1:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
Amendment 1 to ISO 12402-7:2006 was prepared by Technical Committee ISO/TC 188, Small craft,
Subcommittee SC 1, Personal safety equipment, in collaboration with Technical Committee CEN/TC 162,
Protective clothing including hand and arm protection and lifejackets.
ISO 12402-7:2006/Amd.1:2011(E)
Personal flotation devices —
Part 7:
Materials and components — Safety requirements and test
methods
AMENDMENT 1
Page 1, Normative references
Replace:
“ISO 31 (all parts), Quantities and units”
with
“ISO 80000 (all parts), Quantities and units
IEC 80000 (all parts), Quantities and units”
Replace:
“ISO 2062, Textiles — Yarns from packages — Determination or single-end breaking force and elongation at
break”
with
“ISO 2062, Textiles — Yarns from packages — Determination of single-end breaking force and elongation at
break using constant rate of extension (CRE) tester”
Page 3, Normative references
Replace:
“ASTM D 471-98, Standard Test Method for Rubber Property-Effect of Liquids”
with
“ASTM D 471-06, Standard Test Method for Rubber Property — Effect of Liquids”
Page 5, 4.1.4
In the first line, replace “ISO 31” with “ISO 80000 and IEC 80000”.
”Page 6, 4.1.6.3
Replace the first sentence with the following:
“Where required by the test method, the component or sample of fabric shall be conditioned, in its normal
storage state, and then immediately exposed for (24 ± 0,5) h at a temperature of (−30 ± 2) °C, then for
(24 ± 0,5) h at a temperature of (60 ± 2) °C.”
ISO 12402-7:2006/Amd.1:2011(E)
Page 7, 4.1.6.4
Add the following after the last list item:
“NOTE This test is not applicable to fabrics related to PFDs complying with ISO 12402-5.”
Page 8, 4.3.2.2
Replace the complete subclause with the following:
“4.3.2.2 Textile woven fabrics shall have an as-received tensile strength as specified in Table 2, measured
using the grab method given in ISO 13934-2.”
Page 8, 4.3.2.3
Replace the complete subclause with the following:
“4.3.2.3 Textile knitted fabrics shall have an as-received burst strength as specified in Table 2, measured
using the method given in ISO 13938-1 or ISO 13938-2.”
Page 9, Table 2
Replace Table 2 with the following:
Table 2 — Fabric
a
Property Exposure Test method Number of Compliance criteria
Sample size
samples
(mm × mm)
Tensile 1 Standard ISO 13934-2, 5 warp and As specified by Following exposure 1, the average of
strength conditioning except that jaw 5 weft for test method 5 samples shall be at least 400 N for
(woven breaks may be each each direction.
2 Accelerated
fabrics only) included in the separate
weathering Following each separate exposure 2
average results. exposure
according to and 3, the average of 5 samples shall
4.1.6.4 be at least 260 N.
3 70 h
immersion in:
3.1 fuel B
according to
ASTM D 471-06
or diesel fuel
according to
b
EN 590
3.2 0,5 %
detergent
according to
ISO 6330
2 © ISO 2011 – All rights reserved
ISO 12402-7:2006/Amd.1:2011(E)
Table 2 (continued)
a
Property Exposure Test method Number of Compliance criteria
Sample size
samples
(mm × mm)
Bursting 1 Standard ISO 13938-1 or 10 for each Following exposure 1, the average of
130 × 130
strength conditioning ISO 13938-2 separate 10 samples shall be at least 800 kPa.
(knitted exposure
2 Accelerated Following each separate exposure in
fabrics only)
weathering 2 and 3, the average of 10 samples
according to shall retain at least 60 % of the
4.1.6.4 strength determined following
standard conditioning.
3 70 h
immersion in:
3.1 fuel B
according to
ASTM D 471-06
or diesel fuel
according to
b
EN 590
3.2 0,5 %
detergent
according to
ISO 6330
Elongation Standard ISO 13934-1 5 warp and As Following standard conditioning, the
at break conditioning 5 weft specified by average of 5 samples shall not
(woven test method exceed a 60 % increase of elongation
fabrics only) at break.
Tearing Standard ISO 13937-2 5 warp 50 × 200 The average of 5 samples shall be at
strength conditioning 5 weft least 25 N for each direction.
(woven
fabrics only)
Yarn Standard See 4.3.2.6 5 warp 100 × 150 The average of 5 samples shall be at
slippage conditioning 5 weft least 220 N.
(woven
fabrics only)
Openness Sta
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.