EN 2002-002:2005
(Main)Aerospace series - Metallic materials - Test methods - Part 2: Tensile testing at elevated temperature
Aerospace series - Metallic materials - Test methods - Part 2: Tensile testing at elevated temperature
This standard specifies the requirements for the tensile testing of metallic materials at elevated temperature for aerospace applications.
It shall be applied when referred to in the EN technical specification or material standard unless otherwise specified on the drawing, order or inspection schedule.
Luft- und Raumfahrt - Metallische Werkstoffe - Prüfverfahren - Teil 2: Zugversuch bei Hochtemperatur
Diese Norm legt die Anforderungen für den Zugversuch bei Hochtemperatur von metallischen Werkstoffen für Anwendungen in der Luft- und Raumfahrt fest.
Diese Norm ist anzuwenden, wenn in den technischen Lieferbedingungen einer EN-Norm oder in einer EN Werkstoffnorm darauf verwiesen wird, sofern nicht anders in der Zeichnung, Auftrags- oder Prüfliste fest¬gelegt.
Série aérospatiale - Matériaux métalliques - Méthodes d'essais applicables - Partie 2 : Essais de traction à temperature élevée
Aeronavtika – Kovinski materiali – Preskusne metode – 2. del: Natezni preskus pri povišani temperaturi
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aeronavtika – Kovinski materiali – Preskusne metode – 2. del: Natezni preskus pri povišani temperaturiLuft- und Raumfahrt - Metallische Werkstoffe - Prüfverfahren - Teil 2: Zugversuch bei HochtemperaturSérie aérospatiale - Matériaux métalliques - Méthodes d'essais applicables - Partie 2 : Essais de traction a temperature élevéeAerospace series - Metallic materials - Test methods - Part 2: Tensile testing at elevated temperature49.025.05Železove zlitine na splošnoFerrous alloys in generalICS:Ta slovenski standard je istoveten z:EN 2002-002:2005SIST EN 2002-002:2006en01-julij-2006SIST EN 2002-002:2006SLOVENSKI
STANDARD
SIST EN 2002-002:2006
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 2002-002November 2005ICS 49.025.05; 49.025.15 English VersionAerospace series - Metallic materials - Test methods - Part 2:Tensile testing at elevated temperatureSérie aérospatiale - Matériaux métalliques - Méthodesd'essais applicables - Partie 2 : Essais de traction àtemperature élevéeLuft- und Raumfahrt - Metallische Werkstoffe -Prüfverfahren - Teil 2: Zugversuch bei HochtemperaturThis European Standard was approved by CEN on 19 September 2005.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2005 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 2002-002:2005: ESIST EN 2002-002:2006
EN 2002-002:2005 (E) 2 Contents Page Foreword.3 Introduction.4 1 Scope.4 2 Normative references.4 3 Terms, definitions and symbols.4 4 Health and safety.7 5 Principle.7 6 Testing requirements.7 7 Test report.14 Annex A (normative)
Types of test piece to be used for sheet and strip with thickness less than or equal to 8 mm.16 Annex B (normative)
Types of non-machined test piece to be used in the case of bar, section and wire with a diameter or thickness less than or equal to 8 mm.18 Annex C (normative)
Types of machined test piece to be used in the case of bar, section, plate and wire with diameter or thickness greater than 8 mm and for forgings and castings.19 Annex D (normative)
Types of test piece to be used in the case of tubes.22
SIST EN 2002-002:2006
EN 2002-002:2005 (E) 3 Foreword This European Standard (EN 2002-002:2005) has been prepared by the European Association of Aerospace Manufacturers - Standardization (AECMA-STAN). After enquiries and votes carried out in accordance with the rules of this Association,
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.