iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
CEN

EN 307:1998

(Main)

Heat exchangers - Guidelines to prepare installation, operating and maintenance instructions required to maintain the performance of each type of heat exchangers

Heat exchangers - Guidelines to prepare installation, operating and maintenance instructions required to maintain the performance of each type of heat exchangers

This European Standard gives guidance on the preparation of manufacturer's instructions for the installation, operation and maintenance of heat exchangers. Meeting the recommendations in this standard does not remove the manufacturers/installers responsibility to provide all necessary specific information to ensure the safe and efficient working of their equipment.

Wärmeaustauscher - Anleitung für die Anfertigung von Einbau- und Betriebsanleitungen und Wartungsanweisungen zum Erhalt der Leistung von Wärmeaustauschern jeglicher Bauart

Diese Europäische Norm gibt eine Anleitung für die Anfertigung von Hersteller-Einbau- und Betriebsanleitungen sowie von Wartungsanleitungen für Wärmeaustauscher. Die Empfehlungen in dieser Norm entbinden Herstell-/Montagebetriebe nicht von der Verantwortung, alle erforderlichen spezifischen Informationen zur Sicherstellung des Zuverlässigen und effektiven Betriebs der Anlage zur Verfügung zu stellen.

Echangeurs thermiques - Guide de préparation des notices d'installation, de fonctionnement et de maintenance nécessaires au maintien des performances de tous les types d'échangeurs thermiques

La présente norme européenne donne des indications pour la préparation des notices du constructeur concernant l'installation, le fonctionnement et la maintenance des échangeurs thermiques. La satisfaction aux recommandations de la présente norme européenne ne remet pas en cause la responsabilité des constructeurs/installateurs de fournir toutes les informations spécifiques nécessaires au fonctionnement sûr et efficace de leur équipement.

Prenosniki toplote – Smernice za pripravo navodil za vgradnjo, obratovanje in vzdrževanje, ki zagotavljajo pravilno delovanje posameznih tipov prenosnikov toplote

General Information

Status
Published
Publication Date
22-Sep-1998
Withdrawal Date
30-Mar-1999
ICS
27.060.30 - Boilers and heat exchangers
Technical Committee
CEN/TC 110 - Heat exchangers
Drafting Committee
CEN/TC 110/WG 1 - Heat exchangers used in the field of refrigeration and air conditioning
Current Stage
9093 - Decision to confirm - Review Enquiry
Completion Date
12-Oct-2023
Directive
305/2011 - Regulation (eu) No 305/2011 of the European Parliament and of the Council of 9 march 2011 laying down harmonised conditions for the marketing of construction products and repealing council directive 89/106/eec
89/106/EEC - Construction products
Mandate
M/BC/CEN/87/5 - Standardization request concerning heat exchangers
Ref Project
SIST EN 307:1999 - Heat exchangers - Guidelines to prepare installation, operating and maintenance instructions required to maintain the performance of each type of heat exchangers

Buy Standard

EN 307:1999EN 307:1999
PreviousNext
Standard
EN 307:1999
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-december-1999
Prenosniki toplote – Smernice za pripravo navodil za vgradnjo, obratovanje in
vzdrževanje, ki zagotavljajo pravilno delovanje posameznih tipov prenosnikov
toplote
Heat exchangers - Guidelines to prepare installation, operating and maintenance
instructions required to maintain the performance of each type of heat exchangers
Wärmeaustauscher - Anleitung für die Anfertigung von Einbau- und Betriebsanleitungen
und Wartungsanweisungen zum Erhalt der Leistung von Wärmeaustauschern jeglicher
Bauart
Echangeurs thermiques - Guide de préparation des notices d'installation, de
fonctionnement et de maintenance nécessaires au maintien des performances de tous
les types d'échangeurs thermiques
Ta slovenski standard je istoveten z: EN 307:1998
ICS:
27.060.30 Grelniki vode in prenosniki Boilers and heat exchangers
toplote
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

CEN
EN 308:2022(Main)
Heat exchangers - Test procedures for establishing performance of air to air heat recovery components
SIST EN 308:2022

This document specifies methods to be used for testing of air-to-air heat recovery components (HRC). The main purpose of the HRC is to exchange heat between exhaust air and supply air in order to save energy, which results in
—   preheat or heat, and/or
—   precool or cool
supply air in ventilation systems or air conditioning systems. Optionally HRC can exchange air humidity between exhaust and supply air. The HRC contains the heat exchangers and all necessary features and auxiliary devices for the exchange of sensible heat and (if available) air humidity between exhaust air and supply air. The HRC will be installed in casings or ducts. If fans are part of the test unit, the effect of the fan power on the measured values will be corrected.
This document specifies procedures and input criteria required for tests to determine the performance of a HRC at one or several test conditions, each of them with continuous and stationary air flows, air temperatures and humidities at both inlet sides. Three different test types are covered:
—   Test type A, Laboratory testing of HRC installed in test casings (A1) or a HRC sections (A2);
—   Test type B, Laboratory testing of HRC installed in non-residential ventilation units  in design configuration;
—   Test type C, on-site (field) testing of HRC in non-residential ventilation units (C1) or a HRC sections (C2) in operation configuration.
This document is applicable to recuperators, regenerators, and HRC with intermediary heat transfer medium.
This document prescribes test methods for determining:
1)   the temperature and humidity efficiency,
2)   the pressure drop of exhaust air and supply air sides,
3)   possible internal leakages; exhaust air transfer ratio (EATR) and outdoor air correction factor (OACF),
4)   external leakages and
5)   auxiliary energy used for the operation of the HRC.
HRC using heat pumps are not covered by this document.

  • Standard
    86 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 13487:2019(Main)
Heat exchanger - Forced convection air cooled refrigerant condensers and dry coolers - Sound measurement
SIST EN 13487:2019

1.1   General
This document is one of a series dedicated to air-cooled heat exchangers.
-   forced convection air cooled refrigerant condensers as specified in EN 327;
-   forced convection unit air coolers for refrigeration as specified in EN 328;
-   air cooled liquid coolers "dry coolers" as specified in EN 1048.
This document provides information for assessing and presenting the acoustic emission characteristics of heat exchangers under stationary operating conditions.
This document is applicable to selfstanding forced convection air cooled refrigerant condensers and air cooled liquid coolers "dry coolers" and air coolers.
1.2   Size of source
The method specified in EN ISO 3744, EN ISO 3745, EN ISO 3746, EN ISO 9614 1, EN ISO 9614 2 and EN ISO 9614-3 is applicable to noise sources of any size. Limitations for the size of the source are given in 1.3 of EN ISO 3741:2010, EN ISO 3743 1:2010 and EN ISO 3743 2:2009.
1.3   Object
This document offers ways to determine the sound power level of units. Some of them are specifically adapted to provide results with low uncertainties, by using laboratory class or engineering class acoustic methods under highly controlled working conditions. Those results are suitable for certification, labeling and marking purposes.
This document is concerned with objective methods for determining sound power levels LW, expressed in decibels (dB) with reference to a sound power of one picowatt (1 pW), of airborne acoustical noise within the specified frequency range of interest and for prescribed operating conditions of the appliance to be measured:
-   A-weighted sound power level, LWA;
-   spectral sound power levels;
-   emission sound pressure level at workplace, LpA.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1048:2014(Main)
Heat exchangers - Air cooled liquid coolers ('dry coolers') - Test procedures for establishing the performance
SIST EN 1048:2014

This European Standard applies to remote forced convection air cooled liquid coolers, within which no change in the liquid phase occurs.
This European Standard does not apply to liquid coolers, designed primarily for installation within the machinery compartment of packaged products.
Its purpose is to establish uniform methods to test and ascertain the following:
-   Product identification;
-   Capacity;
-   Air flow rate;
-   Liquid side pressure drop;
-   Energy requirements.
This European Standard does not cover technical safety aspects.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 327:2014(Main)
Heat exchangers - Forced convection air cooled refrigerant condensers - Test procedures for establishing performance
SIST EN 327:2014

This European Standard applies to non ducted forced convection air cooled refrigerant condensers/gas coolers with dry air side surface within which the refrigerant changes phases or is cooled. Its purpose is to establish uniform methods of performance assessment. It does not deal with evaluation of conformity.
This standardEuropean Standard does not apply to air cooled condensers/gas coolers, designed primarily for installation within the machinery compartment of packaged products or in factory-assembled condensing/gas cooling units.
This European Standard does not apply to condensers with an integral subcooling part.
This European Standard specifies methods to test and ascertain the following:
-   product identification;
-   standard capacity;
-   nominal air flow rate;
-   nominal fan power.
This standard does not cover technical safety aspects.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 328:2014(Main)
Heat exchangers - Forced convection unit air coolers for refrigeration - Test procedures for establishing the performance
SIST EN 328:2014

This European Standard is applicable to non-ducted unit air coolers for refrigeration operating:
a)   with direct dry expansion of a refrigerant;
b)   with liquid overfeed by pump circulation of a refrigerant;
c)   with a liquid.
This standard specifies uniform methods of performance assessment to test and ascertain the following:
-                product identification;
-   standard capacity;
-   standard liquid pressure drop;
-   standard refrigerant pressure drop (for operation with liquid overfeed by pump circulation only);
-   nominal air flow rate;
-   nominal fan power.
It does not cover evaluation of conformity.
It is not applicable to air coolers for duct mounting or with natural air convection.
This standard does not cover technical safety aspects.

  • Standard
    46 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 14705:2005(Main)
Heat exchangers - Method of measurement and evaluation of thermal performances of wet cooling towers
SIST EN 14705:2005

This European Standard specifies requirements, test methods and acceptance tests for thermal performances pumping head verification of wet cooling towers and plume abatement for wet/dry cooling towers.
This European Standard is applicable to natural draught wet cooling towers (see in 3.1.2.2) fan assisted natural draught cooling tower (see 3.1.2.3), wet/dry cooling towers (see 3.1.2.4) and "Mechanical draught cooling towers", except series ones.
It specifies the test methods, the apparatus required, the limitation of errors and the method for results examination.
The acceptance testing covers the verification of the thermal performance data and pumping head of the cooling tower as specified in the contract between the supplier and the purchaser. If these tests are required then this should be recognized at the time of the contract, as additional fittings, and preparations for the test may be required.
Deviations from the rules laid down below as well as additions need special agreement between purchaser and supplier and should be documented.
This standard does not apply to mechanical draught series wet cooling towers which are dealt with in prEN 13741.
NOTE   Terms like "design", "values", "guarantee" and "acceptance" used in this standard should be understood in a technical but not in a legal or commercial sense.

  • Standard
    62 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1117:1998/A1:2002(Amendment)
Heat exchangers - Liquid cooled refrigerant condensors - Test procedures for establishing the performance
SIST EN 1117:1999/A1:2004

UAP of 4 months (TC Res 146c/1998) (CC/001115)
2020-01-20: Originator of XML version: NEN (on behalf of NEN, ASI, DS, SFS, SIS, SN)

  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1118:1998/A1:2002(Amendment)
Heat exchangers - Refrigerant cooled liquid coolers - Test pocedure for establishing the performance
SIST EN 1118:1999/A1:2004

UAP of 4 months (TC Res 146d/1998) (CC/001115)
2020-01-20: Originator of XML version: NEN (on behalf of NEN, ASI, DS, SFS, SIS, SN)

  • Amendment
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1216:1998/A1:2002(Amendment)
Heat exchangers - Forced circulation air-cooling and air-heating coils - Test procedures for establishing the performance
SIST EN 1216:1999/A1:2004

UAP of 4 months (TC Res 146e/1998) (CC/001115)
2020-01-20: Originator of XML version: NEN (on behalf of NEN, ASI, DS, SFS, SIS, SN)

  • Amendment
    7 pages
    English language
    sale 10% off
    e-Library read for
    1 day
CEN
EN 1118:1998(Main)
Heat exchangers - Refrigerant cooled liquid coolers - Test procedures for establishing the performance
SIST EN 1118:1999

This European Standard applies to series produced liquid coolers which operate with a (primary) refrigerant and its purpose is to establish uniform methods to test and ascertain the following: - Product identification - Capacity-Liquid flow rate-Liquid side pressure drop. This Standard does not cover technical safety aspects.

  • Standard
    43 pages
    English language
    sale 10% off
    e-Library read for
    1 day