EN ISO 19111:2020/prA2

Geographic information - Referencing by coordinates - Amendment 2 (ISO 19111:2019/DAM 2:2023)

Geoinformation - Koordinatenreferenzsysteme - Änderung 2 (ISO 19111:2019/DAM 2:2023)

Information géographique - Système de références par coordonnées - Amendement 2 (ISO 19111:2019/DAM 2:2023)

Geografske informacije - Lociranje s koordinatami - Dopolnilo A2 (ISO 19111:2019/DAM 2:2023)

General Information

• Status: Not Published
• Publication Date: 15-Dec-2024
• ICS: 35.240.70 - IT applications in science
• Technical Committee: CEN/TC 287 - Geographic Information
• Drafting Committee: CEN/TC 287 - Geographic Information
• Current Stage: 6055 - CEN Ratification completed (DOR) - Publishing
• Start Date: 12-Jun-2023
• Completion Date: 12-Jun-2023
• Ref Project: SIST EN ISO 19111:2020/oprA2:2023 - Geographic information - Referencing by coordinates - Amendment 2 (ISO 19111:2019/DAM 2:2023)

Relations

• Amends: EN ISO 19111:2020 - Geographic information - Referencing by coordinates (ISO 19111:2019)
• Effective Date: 14-Dec-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 19111:2020/oprA2:2023
01-maj-2023
Geografske informacije - Lociranje s koordinatami - Dopolnilo A2 (ISO
19111:2019/DAM 2:2023)
Geographic information - Referencing by coordinates - Amendment 2 (ISO
19111:2019/DAM 2:2023)
Geoinformation - Koordinatenreferenzsysteme - Änderung 2 (ISO 19111:2019/DAM
2:2023)
Information géographique - Système de références par coordonnées - Amendement 2
(ISO 19111:2019/DAM 2:2023)
Ta slovenski standard je istoveten z: EN ISO 19111:2020/prA2
ICS:
07.040 Astronomija. Geodezija. Astronomy. Geodesy.
Geografija Geography
35.240.70 Uporabniške rešitve IT v IT applications in science
znanosti
SIST EN ISO 19111:2020/oprA2:2023 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 19111:2020/oprA2:2023
---------------------- Page: 2 ----------------------
SIST EN ISO 19111:2020/oprA2:2023
DRAFT AMENDMENT
ISO 19111:2019/DAM 2
ISO/TC 211 Secretariat: SIS
Voting begins on: Voting terminates on:
2023-02-16 2023-05-11
Geographic information — Referencing by coordinates
AMENDMENT 2
ICS: 35.240.70
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO 19111:2019/DAM 2:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023
---------------------- Page: 3 ----------------------
SIST EN ISO 19111:2020/oprA2:2023
ISO 19111:2019/DAM 2:2023(E)
DRAFT AMENDMENT
ISO 19111:2019/DAM 2
ISO/TC 211 Secretariat: SIS
Voting begins on: Voting terminates on:
Geographic information — Referencing by coordinates
AMENDMENT 2
ICS: 35.240.70
This document is circulated as received from the committee secretariat.
COPYRIGHT PROTECTED DOCUMENT
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2023
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

NOT BE REFERRED TO AS AN INTERNATIONAL

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.

the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below

IN ADDITION TO THEIR EVALUATION AS

or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,

TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: [phone]
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: [e-mail]
NATIONAL REGULATIONS.
Website: www.iso.org ISO 19111:2019/DAM 2:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
© ISO 2023 – All rights reserved
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2022
---------------------- Page: 4 ----------------------
SIST EN ISO 19111:2020/oprA2:2023
ISO 19111:2019/DAM 2:2022(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www.iso.org/patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to

the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see

www.iso.org/iso/foreword.html.

This document was prepared by Technical Committee ISO/TC 211, Geographic information/Geomatics.

iii
© ISO 2022 – All rights reserved
---------------------- Page: 5 ----------------------
SIST EN ISO 19111:2020/oprA2:2023
ISO 19111:2019/DAM 2:2022(E)
Introduction

The purpose of this amendment is to correct minor omissions in 19111:2019/Amd 1:2021 identified

during implementation of ISO 19162:2019 "Geographic information — Well-known text representation

of coordinate reference systems" which is dependent upon the abstract data model described in

ISO 19111.
1. Amendment to spherical coordinate system.

Planetary science has a requirement to describe location through two-dimensional geocentric latitude

and longitude. ISO 19111:2019 describes a three-dimensional spherical coordinate system. This

amendment allows a spherical coordinate system to be either two- or three-dimensional.

2. Addition of datum anchor epoch attribute to UML datums class.

Modern static geodetic reference frames are usually defined to be consistent with ITRF at a specified

epoch. It is desirable that this epoch be an optional attribute of such reference frames. As it could have

broader applicability the attribute is generalised through inclusion in the datum class.

3. Addition of defining transformation.

Modern geodetic coordinate reference systems may be defined through a transformation from another

coordinate reference systems. This addition permits such transformations to be shown as an attribute

of the defined coordinate reference system.
4. Clarification of use of derived projected CRS in compound CRSs.
5. Correction of very minor typograpic errors.

In some UML constraints an erroneous opening left parenthesis is replaced by an opening curly bracket.

© ISO 2022 – All rights reserved
---------------------- Page: 6 ----------------------
SIST EN ISO 19111:2020/oprA2:2023
ISO 19111:2019/DAM 2:2022(E)
Geographic information — Referencing by coordinates
AMENDMENT 2
3.1.16, datum ensemble

In EXAMPLE, remove right parentheis after "...and G1762." The complete revised definition becomes:

3.1.16
datum ensemble

group of multiple realizations of the same terrestrial or vertical reference system that, for approximate

spatial referencing purposes, are not significantly different

EXAMPLE “WGS 84” as an undifferentiated group of realizations including WGS 84 (TRANSIT), WGS 84

(G730), WGS 84 (G873), WGS 84 (G1150), WGS 84 (G1674) and WGS 84 (G1762). At the surface of the Earth these

have changed on average by 0.7m between the TRANSIT and G730 realizations, a further 0.2m between G730 and

G873, 0.06m between G873 and G1150, 0.2m between G1150 and G1674 and 0.02m between G1674 and G1762.

Note 1 to entry: Datasets referenced to the different realizations within a datum ensemble may be merged

without coordinate transformation.

Note 2 to entry: ‘Approximate’ is for users to define but typically is in the order of under 1 decimetre but may be

up to 2 metres.
3.1.31, geodetic coordinate reference system
Replace definition with
3.1.31
geodetic coordinate reference system

two- or three-dimensional coordinate reference system based on a geodetic reference frame and having

either a three-dimensional Cartesian or an ellipsoidal or a spherical coordinate system

Note 1 to entry: In this document a coordinate reference system based on a geodetic reference frame and having

an ellipsoidal coordinate system is geographic.
3.1.60, spherical coordinate system
Replace definition with
3.1.60
spherical coordinate system

two- or three-dimensional coordinate system in Euclidean space in which position is specified by two

angular coordinates and (in the three-dimensional case) one distance coordinate

Note 1 to entry: Not to be confused with an ellipsoidal coordinate system based on an ellipsoid ‘degenerated’ into

a sphere.
9.3.2, Spatial compound coordinate reference system
© ISO 2022 – All rights reserved
---------------------- Page: 7 ----------------------
SIST EN ISO 19111:2020/oprA2:2023
ISO 19111:2019/DAM 2:2022(E)
After 9.3.2 (f) add:
g) Derived projected 2D + Vertical CRS
h) Derived projected 2D + Engineering 1D (near vertical)
9.3.4, Spatio-parametric compound coordinate reference system
Replace text with:

A spatio-parametric coordinate reference system is a compound CRS in which one component is a

geographic 2D, projected 2D, engineering 2D CRS or derived projected 2D CRS, supplemented by

a parametric CRS to create a three-dimensional CRS: an example is included in E.3.3. More than one

parametric coordinate reference system may be included if these represent independent parametric

quantities.
9.4, UML schema for the Coordinate Reference Systems package

In paragraph 4 after "... detailed in Clause 12." insert an additional new last sentence:

Associations between Coordinate Reference Systems and Coordinate Operations are summarised in

the UML class diagram in Clause 12, Figure 17.
9.4, Figure 9
Replace Figure 9 with the following:
© ISO 2022 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 19111:2020/oprA2:2023
ISO 19111:2019/DAM 2:2022(E)
Figure 9 — UML diagram — Coordinate Reference Systems package
9.4, Table 10
Replace Table 10 with the following:
Table 10 — Defining elements of Coordinate Reference Systems::GeodeticCRS class

Definition: coordinate reference system associated with a geodetic reference frame and a three-di-

mensional Cartesian or spherical coordinate system

Note: If the geodetic reference frame is dynamic then the geodetic CRS is dynamic, else it is

static.
Stereotype: Interface
Class attribute: Concrete
© ISO 2022 – All rights reserved
---------------------- Page: 9 ----------------------
SIST EN ISO 19111:2020/oprA2:2023
ISO 19111:2019/DAM 2:2022(E)
TTabablele 1 100 ((ccoonnttiinnueuedd))
Inheritance SingleCRS
from:
Generalization GeographicCRS, DerivedGeodeticCRS
of:
Association associations inherited from SingleCRS, plus:
roles:
Association Obliga- Maximum
name UML identifier Association with tion O
...

SLOVENSKI STANDARD
SIST EN ISO 19111:2020/prA2:2023
01-maj-2023
Geografske informacije - Lociranje s koordinatami - Dopolnilo A2 (ISO
19111:2019/DAM 2:2023)
Geographic information - Referencing by coordinates - Amendment 2 (ISO
19111:2019/DAM 2:2023)
Geoinformation - Koordinatenreferenzsysteme - Änderung 2 (ISO 19111:2019/DAM
2:2023)
Information géographique - Système de références par coordonnées - Amendement 2
(ISO 19111:2019/DAM 2:2023)
Ta slovenski standard je istoveten z: EN ISO 19111:2020/prA2
ICS:
07.040 Astronomija. Geodezija. Astronomy. Geodesy.
Geografija Geography
35.240.70 Uporabniške rešitve IT v IT applications in science
znanosti
SIST EN ISO 19111:2020/prA2:2023 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 19111:2020/prA2:2023
---------------------- Page: 2 ----------------------
SIST EN ISO 19111:2020/prA2:2023
DRAFT AMENDMENT
ISO 19111:2019/DAM 2
ISO/TC 211 Secretariat: SIS
Voting begins on: Voting terminates on:
2023-02-16 2023-05-11
Geographic information — Referencing by coordinates
AMENDMENT 2
ICS: 35.240.70
This document is circulated as received from the committee secretariat.
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO 19111:2019/DAM 2:2023(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2023
---------------------- Page: 3 ----------------------
SIST EN ISO 19111:2020/prA2:2023
ISO 19111:2019/DAM 2:2023(E)
DRAFT AMENDMENT
ISO 19111:2019/DAM 2
ISO/TC 211 Secretariat: SIS
Voting begins on: Voting terminates on:
Geographic information — Referencing by coordinates
AMENDMENT 2
ICS: 35.240.70
This document is circulated as received from the committee secretariat.
COPYRIGHT PROTECTED DOCUMENT
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
© ISO 2023
ISO/CEN PARALLEL PROCESSING
THEREFORE SUBJECT TO CHANGE AND MAY

All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may

NOT BE REFERRED TO AS AN INTERNATIONAL

be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on STANDARD UNTIL PUBLISHED AS SUCH.

the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below

IN ADDITION TO THEIR EVALUATION AS

or ISO’s member body in the country of the requester. BEING ACCEPTABLE FOR INDUSTRIAL,

TECHNOLOGICAL, COMMERCIAL AND
ISO copyright office
USER PURPOSES, DRAFT INTERNATIONAL
CP 401 • Ch. de Blandonnet 8
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
CH-1214 Vernier, Geneva
POTENTIAL TO BECOME STANDARDS TO
Phone: [phone]
WHICH REFERENCE MAY BE MADE IN
Reference number
Email: [e-mail]
NATIONAL REGULATIONS.
Website: www.iso.org ISO 19111:2019/DAM 2:2022(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
Published in Switzerland
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
© ISO 2023 – All rights reserved
PROVIDE SUPPORTING DOCUMENTATION. © ISO 2022
---------------------- Page: 4 ----------------------
SIST EN ISO 19111:2020/prA2:2023
ISO 19111:2019/DAM 2:2022(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of

any patent rights identified during the development of the document will be in the Introduction and/or

on the ISO list of patent declarations received (see www.iso.org/patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and

expressions related to conformity assessment, as well as information about ISO's adherence to

the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see

www.iso.org/iso/foreword.html.

This document was prepared by Technical Committee ISO/TC 211, Geographic information/Geomatics.

iii
© ISO 2022 – All rights reserved
---------------------- Page: 5 ----------------------
SIST EN ISO 19111:2020/prA2:2023
ISO 19111:2019/DAM 2:2022(E)
Introduction

The purpose of this amendment is to correct minor omissions in 19111:2019/Amd 1:2021 identified

during implementation of ISO 19162:2019 "Geographic information — Well-known text representation

of coordinate reference systems" which is dependent upon the abstract data model described in

ISO 19111.
1. Amendment to spherical coordinate system.

Planetary science has a requirement to describe location through two-dimensional geocentric latitude

and longitude. ISO 19111:2019 describes a three-dimensional spherical coordinate system. This

amendment allows a spherical coordinate system to be either two- or three-dimensional.

2. Addition of datum anchor epoch attribute to UML datums class.

Modern static geodetic reference frames are usually defined to be consistent with ITRF at a specified

epoch. It is desirable that this epoch be an optional attribute of such reference frames. As it could have

broader applicability the attribute is generalised through inclusion in the datum class.

3. Addition of defining transformation.

Modern geodetic coordinate reference systems may be defined through a transformation from another

coordinate reference systems. This addition permits such transformations to be shown as an attribute

of the defined coordinate reference system.
4. Clarification of use of derived projected CRS in compound CRSs.
5. Correction of very minor typograpic errors.

In some UML constraints an erroneous opening left parenthesis is replaced by an opening curly bracket.

© ISO 2022 – All rights reserved
---------------------- Page: 6 ----------------------
SIST EN ISO 19111:2020/prA2:2023
ISO 19111:2019/DAM 2:2022(E)
Geographic information — Referencing by coordinates
AMENDMENT 2
3.1.16, datum ensemble

In EXAMPLE, remove right parentheis after "...and G1762." The complete revised definition becomes:

3.1.16
datum ensemble

group of multiple realizations of the same terrestrial or vertical reference system that, for approximate

spatial referencing purposes, are not significantly different

EXAMPLE “WGS 84” as an undifferentiated group of realizations including WGS 84 (TRANSIT), WGS 84

(G730), WGS 84 (G873), WGS 84 (G1150), WGS 84 (G1674) and WGS 84 (G1762). At the surface of the Earth these

have changed on average by 0.7m between the TRANSIT and G730 realizations, a further 0.2m between G730 and

G873, 0.06m between G873 and G1150, 0.2m between G1150 and G1674 and 0.02m between G1674 and G1762.

Note 1 to entry: Datasets referenced to the different realizations within a datum ensemble may be merged

without coordinate transformation.

Note 2 to entry: ‘Approximate’ is for users to define but typically is in the order of under 1 decimetre but may be

up to 2 metres.
3.1.31, geodetic coordinate reference system
Replace definition with
3.1.31
geodetic coordinate reference system

two- or three-dimensional coordinate reference system based on a geodetic reference frame and having

either a three-dimensional Cartesian or an ellipsoidal or a spherical coordinate system

Note 1 to entry: In this document a coordinate reference system based on a geodetic reference frame and having

an ellipsoidal coordinate system is geographic.
3.1.60, spherical coordinate system
Replace definition with
3.1.60
spherical coordinate system

two- or three-dimensional coordinate system in Euclidean space in which position is specified by two

angular coordinates and (in the three-dimensional case) one distance coordinate

Note 1 to entry: Not to be confused with an ellipsoidal coordinate system based on an ellipsoid ‘degenerated’ into

a sphere.
9.3.2, Spatial compound coordinate reference system
© ISO 2022 – All rights reserved
---------------------- Page: 7 ----------------------
SIST EN ISO 19111:2020/prA2:2023
ISO 19111:2019/DAM 2:2022(E)
After 9.3.2 (f) add:
g) Derived projected 2D + Vertical CRS
h) Derived projected 2D + Engineering 1D (near vertical)
9.3.4, Spatio-parametric compound coordinate reference system
Replace text with:

A spatio-parametric coordinate reference system is a compound CRS in which one component is a

geographic 2D, projected 2D, engineering 2D CRS or derived projected 2D CRS, supplemented by

a parametric CRS to create a three-dimensional CRS: an example is included in E.3.3. More than one

parametric coordinate reference system may be included if these represent independent parametric

quantities.
9.4, UML schema for the Coordinate Reference Systems package

In paragraph 4 after "... detailed in Clause 12." insert an additional new last sentence:

Associations between Coordinate Reference Systems and Coordinate Operations are summarised in

the UML class diagram in Clause 12, Figure 17.
9.4, Figure 9
Replace Figure 9 with the following:
© ISO 2022 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 19111:2020/prA2:2023
ISO 19111:2019/DAM 2:2022(E)
Figure 9 — UML diagram — Coordinate Reference Systems package
9.4, Table 10
Replace Table 10 with the following:
Table 10 — Defining elements of Coordinate Reference Systems::GeodeticCRS class

Definition: coordinate reference system associated with a geodetic reference frame and a three-di-

mensional Cartesian or spherical coordinate system

Note: If the geodetic reference frame is dynamic then the geodetic CRS is dynamic, else it is

static.
Stereotype: Interface
Class attribute: Concrete
© ISO 2022 – All rights reserved
---------------------- Page: 9 ----------------------
SIST EN ISO 19111:2020/prA2:2023
ISO 19111:2019/DAM 2:2022(E)
TTabablele 1 100 ((ccoonnttiinnueuedd))
Inheritance SingleCRS
from:
Generalization GeographicCRS, DerivedGeodeticCRS
of:
Association associations inherited from SingleCRS, plus:
roles:
Association Obliga- Maximum
name UML identifier Association with tion Occ
...