EN ISO 21180:2006
(Main)Light conveyor belts - Determination of the maximum tensile strength (ISO 21180:2005)
Light conveyor belts - Determination of the maximum tensile strength (ISO 21180:2005)
ISO 21180:2005 specifies a test method for the determination of the maximum tensile strength of light conveyor belts according to ISO 21183-1, or of other conveyor belts where ISO 283 is not applicable.
Leichte Fördergurte - Bestimmung der maximalen Zugfestigkeit (ISO 21180:2005)
Diese Europäische Norm legt ein Prüfverfahren fest für die Bestimmung der maximalen Zugfestigkeit von leichten Fördergurten nach ISO 21183-1, oder von anderen Fördergurten, bei denen ISO 283 ungeeignet ist.
Courrroies transporteuses légères - Détermination de la résistance maximale à la traction (ISO 21180:2005)
L'ISO 21180:2005 spécifie une méthode d'essai permettant de déterminer la résistance maximale à la rupture des courroies transporteuses légères, telles que décrites dans l'ISO 21183-1, ou d'autres courroies transporteuses si l'ISO 283 n'est pas applicable.
Naprave za kontinuirni transport – Lahki trakovi tračnih transporterjev – Ugotavljanje največje natezne trdnosti (ISO 21180:2005)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-april-2007
1DSUDYH]DNRQWLQXLUQLWUDQVSRUW±/DKNLWUDNRYLWUDþQLKWUDQVSRUWHUMHY±
8JRWDYOMDQMHQDMYHþMHQDWH]QHWUGQRVWL ,62
Light conveyor belts - Determination of the maximum tensile strength (ISO 21180:2005)
Leichte Fördergurte - Bestimmung der maximalen Zugfestigkeit (ISO 21180:2005)
Courrroies transporteuses légeres - Détermination de la résistance maximale a la
traction (ISO 21180:2005)
Ta slovenski standard je istoveten z: EN ISO 21180:2006
ICS:
53.040.20 Deli za transporterje Components for conveyors
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 21180
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2006
ICS 53.040.10 Supersedes EN 1722:1999
English Version
Light conveyor belts - Determination of the maximum tensile
strength (ISO 21180:2005)
Courrroies transporteuses légères - Détermination de la Leichte Fördergurte - Bestimmung der maximalen
résistance maximale à la traction (ISO 21180:2005) Zugfestigkeit (ISO 21180:2005)
This European Standard was approved by CEN on 21 October 2006.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 21180:2006: E
worldwide for CEN national Members.
Foreword
The text of ISO 21180:2005 has been prepared by Technical Committee ISO/TC 41 "Pulleys and belts
(including veebelts)” of the International Organization for Standardization (ISO) and has been taken over as
by BSI.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by May 2007, and conflicting national standards shall be withdrawn at the
latest by May 2007.
This document supersedes EN 1722:1999.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden,
Switzerland and United Kingdom.
Endorsement notice
The text of ISO 21180:2005 has been approved by CEN as EN ISO 21180:2006 without any modifications.
INTERNATIONAL ISO
STANDARD 21180
First edition
2005-11-01
Light conveyor belts — Determination of
the maximum tensile strength
Courrroies transporteuses légères — Détermination de la résistance
maximale à la traction
Reference number
ISO 21180:2005(E)
©
ISO 2005
ISO 21180:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2005 – All rights reserved
ISO 21180:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 21180 was prepared by Technical Committee ISO/TC 41, Pulleys and belts (including veebelts),
Subcommittee SC 3, Conveyor belts.
This International Standard is based on EN 1722:1999, prepared by CEN/TC 188.
INTERNATIONAL STANDARD ISO 21180:2005(E)
Light conveyor belts — Determination of the maximum tensile
strength
1 Scope
This International Standard specifies a test method for the determination of the maximum tensile strength of
light conveyor belts according to ISO 21183-1, or of other conveyor belts where ISO 283 is not applicable.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
1)
ISO 283 , Textile conveyor belts — Full thickness tensile strength, elongation at break and elongation at the
reference load — Test method
ISO 7500-1:2004, Metallic
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.