EN 3302:2007
(Main)Aerospace series - Bolts in heat resisting steel FE-PM1708 (FV535) - Classification: 1 000 MPa/550 °C - Technical specification
Aerospace series - Bolts in heat resisting steel FE-PM1708 (FV535) - Classification: 1 000 MPa/550 °C - Technical specification
This standard specifies the technical, qualification and quality assurance requirements for bolts in material FE PM1708 (FV535) of tensile strength class 1 000 MPa at room temperature, maximum test temperature of material 550 °C.
Primarily for aerospace applications it is applicable to such bolts when referenced on the product standard or drawing.
Luft- und Raumfahrt - Schrauben aus hochwarmfestem Stahl FE-PM1708 (FV535) - Klasse: 1 000 MPa/550 °C - Technische Lieferbedingungen
Diese Norm legt die technischen Anforderungen, die Anforderungen an die Qualifikation sowie die Anforde¬rungen an die Qualitätssicherung für Schrauben aus dem Werkstoff FE PM1708 (FV535), Zugfestigkeits¬klasse 1 000 MPa bei Raumtemperatur, maximale Prüftemperatur des Werkstoffes 550 °C, fest.
Diese Norm gilt in erster Linie für Anwendungen in der Luft und Raumfahrt und ist auf die Schrauben anzu¬wenden, auf die in der Produktnorm oder Zeichnung verwiesen wird.
Série aérospatiale - Vis en acier résistant à chaud FE-PM1708 (FV535) - Classification: 1 000 MPa/550 °C - Spécification technique
Aeronavtika - Sorniki iz toplotnoodpornega jekla FE-PM1708 (FV535) - Klasifikacija: 1 000 MPa/550 °C - Tehnična specifikacija
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aerospace series - Bolts in heat resisting steel FE-PM1708 (FV535) - Classification: 1 000 MPa/550 °C - Technical specificationSérie aérospatiale - Vis en acier résistant à chaud FE-PM1708 (FV535) - Classification: 1 000 MPa/550 °C - Spécification techniqueLuft- und Raumfahrt - Schrauben aus hochwarmfestem Stahl FE-PM1708 (FV535) - Klasse: 1 000 MPa/550 °C - Technische LieferbedingungenTa slovenski standard je istoveten z:EN 3302:2007SIST EN 3302:2008en49.030.20ICS:SLOVENSKI
STANDARDSIST EN 3302:200801-marec-2008
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 3302
December 2007 ICS 49.030.20 English Version
Aerospace series - Bolts in heat resisting steel FE-PM1708 (FV535) - Classification: 1 000 MPa/550 °C - Technical specification
Série aérospatiale - Vis en acier résistant à chaud FE-PM1708 (FV535) - Classification: 1 000 MPa/550 °C - Spécification technique
Luft- und Raumfahrt - Schrauben aus hochwarmfestem Stahl FE-PM1708 (FV535) - Klasse: 1 000 MPa/550 °C - Technische Lieferbedingungen This European Standard was approved by CEN on 5 November 2007.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36
B-1050 Brussels © 2007 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 3302:2007: E
EN 3302:2007 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Terms and definitions.5 4 Certification and quality assurance.6 5 Technical requirements and test methods.8
EN 3302:2007 (E) 3 Foreword This document (EN 3302:2007) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2008, and conflicting national standards shall be withdrawn at the latest by June 2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
EN 3302:2007 (E) 4 1 Scope This standard specifies the technical, qualification and quality assurance requirements for bolts in material FE-PM1708 (FV535) of tensile strength class 1 000 MPa at room temperature, maximum test temperature of material 55
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.