Copper and copper alloys - Drawn, round copper wire for the manufacture of electrical conductors

This European Standard specifies the composition, property requirements including electrical properties, and
dimensional tolerances for drawn round copper wire from 0,04 mm up to and including 5,0 mm for the manufacture
of electrical conductors intended for the production of bare and insulated cables and flexible cords.
This standard covers plain or tinned, single or multiline, annealed or hard drawn wire. It does not include wire for
enamelling (winding wire, magnet wire), for electronic application and for contact wire for electric traction.
The sampling procedures, the methods of test for verification of conformity to the requirements of this standard and
the delivery conditions are also specified.
NOTE   Due to the thermal and/or mechanical treatment involved in cablemaking processes, the properties of conductors in the
final cable or cord differ from those of the original wire supplied. Requirements for conductors taken from cable or cord are given
in appropriate cable standards.

Kupfer und Kupferlegierungen - Gezogener Runddraht aus Kupfer zur Herstellung elektrischer Leiter

Diese Europäische Norm legt die Zusammensetzung, die Anforderungen an die Eigenschaften, einschließlich
elektrische Eigenschaften und Grenzabmaße für gezogenen Runddraht aus Kupfer mit Dicken von 0,04 mm bis
5 mm zur Anfertigung elektrischer Leiter fest, die für die Herstellung von Stangen, isolierten Kabeln und Schnüren
bestimmt sind.
Diese Norm gilt für nicht verzinnte, verzinnte, geglühte oder hart gezogene Drähte und für einadrige oder mehradrige
Drähte. Sie gilt nicht für Drähte zum Emaillieren (Spulendraht, Magnetdrähte), zur Verwendung in der Elektronik und
für Kontaktdraht für den elektrischen Fahrbetrieb.
Der Ablauf der Probenentnahme, die Prüfverfahren zur Feststellung der Übereinstimmung mit den Anforderungen
dieser Norm und die Lieferbedingungen sind ebenfalls festgelegt.
ANMERKUNG   Aufgrund der thermischen und/oder mechanischen Behandlung, die im Ablauf der Kabelherstellung auftritt,
weichen die Eigenschaften der Leiter im Kabel oder in der Schnur von denen des gelieferten Originaldrahtes ab. Die Anforderun-
gen für Leiter, die aus Kabeln oder Schnüren entnommen werden, sind in den entsprechenden Normen für Kabel enthalten.

Cuivre et alliages de cuivre - Fils ronds en cuivre étirés pour la fabrication des conducteurs électriques

La présente norme européenne spécifie la composition, les caractéristiques, y compris les caractéristiques électriques et les tolérances de dimensions des fils ronds en cuivre étirés comprises entre 0,04 mm et 5,0 mm inclus pour la fabrication des conducteurs électriques destinés à la production des câbles nus et isolés ainsi que des fils souples.
La présente norme couvre les fils nus ou étamés, monofilaires ou multifilaires, recuits ou écrouis. Elle ne comprend pas les fils destinés à l'émaillage (fils de bobinage, fils aimantés), aux applications électroniques et aux fils de contact pour la traction électrique.
Les procédures d'échantillonnage, les méthodes d'essai pour la vérification de la conformité aux exigences de la présente norme et les conditions de livraison sont également spécifiées.
NOTE   En raison du traitement thermique et/ou mécanique impliqué(s) dans les procédés de fabrication des câbles, les propriétés des conducteurs dans le câble ou le fil final diffèrent de celles du fil fourni à l'origine. Les exigences relatives aux conducteurs pris sur un câble ou un fil fabriqué sont données dans les normes appropriées concernant les câbles.

Baker in bakrove zlitine – Vlečena okrogla bakrova žica za proizvodnjo električnih prevodnikov

General Information

Publication Date
Withdrawal Date
Current Stage
9960 - Withdrawal effective - Withdrawal
Start Date
Completion Date


Buy Standard

EN 13602:2004
English language
21 pages
sale 10% off
sale 10% off
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.SUHYRGQLNRYKupfer und Kupferlegierungen - Gezogener Runddraht aus Kupfer zur Herstellung elektrischer LeiterCuivre et alliages de cuivre - Fils ronds en cuivre étirés pour la fabrication des conducteurs électriquesCopper and copper alloys - Drawn, round copper wire for the manufacture of electrical conductors77.150.30Bakreni izdelkiCopper productsICS:Ta slovenski standard je istoveten z:EN 13602:2002SIST EN 13602:2004en01-januar-2004SIST EN 13602:2004SLOVENSKI

SIST EN 13602:2004

EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 13602March 2002ICS 77.150.30English versionCopper and copper alloys - Drawn, round copper wire for themanufacture of electrical conductorsCuivre et alliages de cuivre - Fils ronds en cuivre étiréspour la fabrication des conducteurs électriquesKupfer und Kupferlegierungen - Gezogener Runddraht ausKupfer zur Herstellung elektrischer LeiterThis European Standard was approved by CEN on 22 February 2002.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2002 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13602:2002 ESIST EN 13602:2004

EN 13602:2002 (E)ContentspageForeword .3
1Scope .4
2Normative references .4
3Terms and definitions .5
4 Designations .5
4.1Material .5
4.2Material condition .5
4.3Product .6
5Ordering information .8
6Requirements .9
6.1Composition .9
6.2Mechanical properties .9
6.3Electrical properties .9
6.4Dimensions .9
6.5Ductility .9
6.6Surface condition .9
7Sampling .10
7.1General .10
7.2Analysis .10
7.3Mechanical, electrical and tin coating tests 10
8Test methods .10
8.1Analysis .10
8.2Tensile test .11
8.3Electrical resistivity test .11
8.4Ductility test .11
8.5Assessment of tin coatings .11
8.6Retests .11
8.7Rounding of results .11
9Declaration of conformity andinspection documentation .12
9.1Declaration of conformity .12
9.2Inspection documentation .1210Marking, packaging, labelling .12Annex A
(informative) Characteristics ofcoppers for electrical purposes .19Bibliography .21TablesTable 1 — Composition of Cu-ETP1 (CW003A)and Cu-OF1 (CW007A) .13Table 2 — Composition of Cu-ETP (CW004A),Cu-FRHC (CW005A) and Cu-OF (CW008A)14Table 3 — Mechanical properties of plain wire15Table 4 — Mechanical properties of tinned wire16Table 5 — Electrical properties (at 20 °C)
..17Table 6 — Tolerances on diameter ........18Table 7— Requirements of tin coatings ....18Table 8 — Number of bends of annealed wire 18Table 9 — Number of bends for hard drawn wire ...........................18Table A.1 — Particular characteristics of coppers for electrical purposes .............202SIST EN 13602:2004

EN 13602:2002 (E)ForewordThis document EN 13602:2002 has been prepared by Technical Committee CEN/TC 133 "Copper and copperalloys", the secretariat of which is held by DIN.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by June 2002, and conflicting national standards shall be withdrawn at the latest byJune 2002.Within its programme of work, Technical Committee CEN/TC 133 requested CEN/TC 133/WG 5 "Copper forelectrical purposes" to prepare the following standard:EN 13602,
Copper and copper alloys — Drawn, round copper wire for the manufacture of electrical conductors

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.