prEN 15012
(Main)Plastics piping systems - Buried and above ground piping components for non pressure soil and waste discharge within the building structure - Requirements and test/assessment methods for pipes and fittings
Plastics piping systems - Buried and above ground piping components for non pressure soil and waste discharge within the building structure - Requirements and test/assessment methods for pipes and fittings
This European Standard specifies product characteristics for plastics pipes and fittings for non-pressure soil and waste applications.
Pipes and fittings covered by this standard are intended to be used in soil and waste discharge applications without pressure:
- inside the building (application area code "B"),
- buried in ground within the building structure (application area code "D") and with a diameter greater than or equal to 75 mm.
This standard gives the associated test/assessment methods.
This standard does not cover adhesives, joint sealings and gaskets.
Kunststoff-Rohrleitungssysteme - Erdverlegte und nicht erdverlegte drucklose Rohrleitungsteile zum Ableiten von Abwasser innerhalb der Gebäudestruktur - Anforderungen und Prüf-/Bewertungsverfahren für Rohre und Formstücke
Diese Europäische Norm legt Produkteigenschaften für Rohre und Formstücke aus Kunststoff für drucklose Anwendungen zum Ableiten von Abwasser fest.
Die in dieser Europäischen Norm behandelten Rohre und Formstücke sind vorgesehen für den Einsatz in drucklosen Anwendungen zum Ableiten von Abwasser:
- innerhalb von Gebäuden (Anwendungskennzeichen „B“);
- erdverlegt innerhalb der Gebäudestruktur (Anwendungskennzeichen „D“) mit einem Durchmesser 75 mm.
Diese Norm enthält die zugehörigen Prüf /Bewertungsverfahren.
Diese Norm gilt nicht für Klebstoffe, Abdichtungen von Rohrverbindungen und Dichtungen.
Systèmes de canalisations en plastique - Composants de canalisations enterrées et aériennes pour l’évacuation des eaux-vannes et des eaux usées sans pression à l’intérieur de la structure des bâtiments - Exigences et méthodes d’essais/d’évaluation pour tubes et raccords
La présente Norme européenne spécifie les caractéristiques de produit relatives aux tubes et raccords en plastique destinés aux applications pour eaux-vannes et eaux usées sans pression.
Les tubes et raccords traités dans la présente norme sont destinés à être utilisés dans les applications d’évacuation des eaux-vannes et des eaux usées sans pression :
- à l’intérieur du bâtiment (code de zone d’application « B ») ;
- enterrées à l'intérieur de la structure du bâtiment (code de zone d’application « D ») et de diamètre égal ou supérieur à 75 mm.
La présente norme indique les méthodes d’essais/d’évaluation associées.
La présente norme ne couvre pas les adhésifs, les joints d’étanchéité et les garnitures de joints.
Cevni sistemi iz polimernih materialov - Podzemne in nadzemne cevne komponente brez tlaka za odvodne sisteme v zgradbah - Zahteve in preskusi/metode ocenjevanja za cevi in fitinge
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-julij-2014
Cevni sistemi iz polimernih materialov - Podzemne in nadzemne cevne
komponente brez tlaka za odvodne sisteme v zgradbah - Zahteve in
preskusi/metode ocenjevanja za cevi in fitinge
Plastics piping systems - Buried and above ground piping components for non pressure
soil and waste discharge within the building structure - Requirements and
test/assessment methods for pipes and fittings
Kunststoff-Rohrleitungssysteme - Erdverlegte und nicht erdverlegte drucklose
Rohrleitungsteile zum Ableiten von Abwasser innerhalb der Gebäudestruktur -
Anforderungen und Prüf-/Bewertungsverfahren für Rohre und Formstücke
Systèmes de canalisations en plastique - Composants de canalisations enterrées et
aériennes pour l’évacuation des eaux-vannes et des eaux usées sans pression à
l’intérieur de la structure des bâtiments - Exigences et méthodes d’essais/d’évaluation
pour tubes et raccords
Ta slovenski standard je istoveten z: prEN 15012
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
23.040.45 Fitingi iz polimernih Plastics fittings
materialov
91.140.80 Drenažni sistemi Drainage systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
DRAFT
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2014
ICS 23.040.01; 91.140.80 Will supersede EN 15012:2007
English Version
Plastics piping systems - Buried and above ground piping
components for non pressure soil and waste discharge within the
building structure - Requirements and test/assessment methods
for pipes and fittings
Systèmes de canalisations en plastique - Composants de Kunststoff-Rohrleitungssysteme - Erdverlegte und nicht
canalisations enterrées et aériennes pour l'évacuation des erdverlegte drucklose Rohrleitungsteile zum Ableiten von
eaux-vannes et des eaux usées sans pression à l'intérieur Abwasser innerhalb der Gebäudestruktur - Anforderungen
de la structure des bâtiments - Exigences et méthodes und Prüf-/Bewertungsverfahren für Rohre und Formstücke
d'essais/d'évaluation pour tubes et raccords
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 155.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 15012:2014 E
worldwide for CEN national Members.
Contents Page
Foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms, definitions and abbreviations . 7
3.1 Terms and definitions . 7
3.2 Abbreviations . 8
4 Product characteristics . 8
4.1 Reaction to fire of pipes and fittings . 8
4.2 Maximum load for admissible deformation of pipes and fittings (only relevant for buried
in ground applications) . 8
4.3 Dimensional tolerances of pipes and fittings . 9
4.4 Tightness: Gas and liquid . 9
4.5 Release of dangerous substances of pipes and fittings . 10
4.6 Durability . 10
5 Test methods . 11
5.1 Reaction to fire of pipes and fittings . 11
5.2 Maximum load for admissible deformation (only relevant for buried in ground
applications) . 11
5.3 Dimensional tolerances . 11
5.4 Tightness: Gas and liquid . 13
5.5 Release of dangerous substances of pipes and fittings . 15
5.6 Durability . 15
6 Assessment and verification of the constancy of performance (AVCP) . 18
6.1 General . 18
6.2 Type testing . 18
6.3 Factory production control (FPC) . 29
Annex ZA (informative) Clauses of this European Standard addressing the provisions of EU
Construction Products Regulation . 46
ZA.1 Scope and relevant characteristics . 46
ZA.2 Procedure for AVCP of plastics pipes and fittings . 48
ZA.3 CE marking and labelling . 53
Bibliography . 59
Foreword
This document (prEN 15012:2014) has been prepared by Technical Committee CEN/TC 155 “Plastics piping
systems and ducting systems”, the secretariat of which is held by NEN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 15012:2007.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.
Introduction
This European Standard specifies only those characteristics of pipes and fittings for soil and waste
applications inside buildings or buried in ground within the building structure, that need to be known to
determine if the works in which these are to be installed can satisfy the essential requirements of the EU
Directive(s). Additional characteristics are specified in the documents listed in clause 2 or in other appropriate
product specifications.
This harmonised European Standard covers plastics pipes and fittings for non pressure soil and waste
applications. Other components such as floor gullies and non return valves are covered by CEN/TC 165.
1 Scope
This European Standard specifies product characteristics for plastics pipes and fittings for non-pressure soil
and waste applications.
Pipes and fittings covered by this standard are intended to be used in soil and waste discharge applications
without pressure:
inside the building (application area code "B"),
buried in ground within the building structure (application area code "D") and with a diameter greater than
or equal to 75 mm.
This standard gives the associated test/assessment methods.
This standard does not cover adhesives, joint sealings and gaskets.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
EN 681-1, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage
applications — Part 1: Vulcanised rubber
EN 681-2, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage
applications — Part 2: Thermoplastic elastomers
EN 681-3, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage
applications — Part 3: Cellular materials of vulcanised rubber
EN 681-4, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage
applications — Part 4: Cast polyurethane sealing elements
EN 727:1994, Plastics piping and ducting systems — Thermoplastics pipes and fittings — Determination of
vicat softening temperature (VST)
EN 728:1997, Plastics piping and ducting systems — Polyolefin pipes and fittings — Determination of
oxidation induction time
EN 1053:1995, Plastics piping systems — Thermoplastics piping systems for non-pressure applications —
Test method for watertightness
EN 1054:1995, Plastics piping systems — Thermoplastics piping systems for soil and waste discharge — Test
method for airtightness of joints
EN 1055:1996, Plastics piping systems — Thermoplastics piping systems for soil and waste discharge inside
buildings — Test method for resistance to elevated temperature cycling
EN 1277:2003, Plastics piping systems — Thermoplastics piping systems for buried non-pressure
applications — Test methods for leaktightness of elastomeric sealing ring type joints
prEN 1329-1:2013, Plastics piping systems for soil and waste discharge (low and high temperature) within the
building structure — Unplasticized poly(vinyl chloride) (PVC-U) — Part 1: Specifications for pipes, fittings and
the system
CEN/TS 1329-2:2012, Plastics piping systems for soil and waste discharge (low and high temperature) within
the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of
conformity
EN 1451-1:1998, Plastics piping systems for soil and waste discharge (low and high temperature) within the
building structure — Polypropylene (PP) — Part 1: Specifications for pipes, fittings and the system
CEN/TS 1451-2:2012, Plastic piping systems for soil and waste discharge (low and high temperature) within
the building structure - Polypropylene (PP) - Part 2: Guidance for the assessment of conformity
EN 1453-1:2000, Plastics piping systems with structured wall-pipes for soil and waste discharge (low and high
temperature) inside buildings — Unplasticized poly(vinyl chloride) (PVC-U) — Part 1: Specifications for pipes
and the system
ENV 1453-2:2000, Plastics piping systems with structured wall pipes for soil and waste discharge (low and
high temperature) inside buildings - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the
assessment of conformity
EN 1455-1:1999, Plastics piping systems for soil and waste discharge (low and high temperature) within the
building structure — Acrylonitrile-butadiene-styrene (ABS) — Part 1: Requirements for pipes, fittings and the
system
CEN/TS 1455-2:2012, Plastics piping systems for soil and waste discharge (low and high temperature) within
the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 2: Guidance for the assessment of
conformity
EN 1519-1:1999, Plastics piping systems for soil and waste discharge (low a
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.