prEN 6024

Aerospace series - Bolts, 100° countersunk reduced head, offset cruciform recess, close tolerance shank, short thread, titanium alloy, lubricated - Classification: 1100 MPa (at ambient temperature)/315°C - Inch series

This document specifies the characteristics for screws, 100° countersunk reduced head, offset cruciform recess, close tolerance shank, short thread, in titanium alloy, anodized, MoS2 lubricated, classification 1 100 MPa /315 °C , inch series, for aerospace applications.

Luft- und Raumfahrt - 100° Senk-Paßschrauben mit reduziertem Kopf, mit Flügelkreuzschlitz, kurzes Gewinde, aus Titanlegierung, anodisiert, MoS<(Index)2> geschmiert - Klasse: 1100 MPa (bei Raumtemperatur)/315 °C; Inch-Reihe

Série aérospatiale - Vis à tête fraisée 100. réduite, à empreinte cruciforme déportée, avec fût à tolérance serrée, filetage court, alliage de titane, lubrifiées - Classification: 1100MPa/315.C - Série en inches

Le présent document spécifie les caractéristiques des vis à tête fraisée 100° réduite, à empreinte cruciforme déportée, tige à tolérance serrée, filetage court, en alliage de titane, anodisées, lubrifiées au MoS2, de classification 1 100 MPa  )/315 °C  ), série en inches, pour applications aérospatiales.

Aeronavtika - Vijaki, 100° ugrezna glava, križna zareza, polno steblo, ozka toleranca, kratek navoj, iz titanove zlitine, anodizirane, mazane z MoS2 - Klasifikacija: 1100 MPa (pri temperaturi okolice)/315 °C - Palčne mere

General Information

• Status: Not Published
• Publication Date: 16-Jul-2023
• ICS: 49.030.20 - Bolts, screws, studs
• Technical Committee: ASD-STAN - Aerospace
• Drafting Committee: ASD-STAN/D 3 - Mechanical
• Current Stage: 3098 - Decision to reject - Consensus building
• Due Date: 13-May-2019
• Completion Date: 13-May-2019
• Ref Project: oSIST prEN 6024:2021 - Aerospace series - Screws, 100° countersunk reduced head offset cruciform recess close tolerance shank, short thread in titanium alloy, anodized MoS2 lubricated - Classification: 1 100 MPa (at ambient temperature)/315 °C - Inch series

Standards Content (Sample)

SLOVENSKI STANDARD
01-september-2021
Aeronavtika - Vijaki, 100° ugrezna glava, križna zareza, polno steblo, ozka
toleranca, kratek navoj, iz titanove zlitine, anodizirane, mazane z MoS2 -
Klasifikacija: 1100 MPa (pri temperaturi okolice)/315 °C - Palčne mere
Aerospace series - Screws, 100° countersunk reduced head offset cruciform recess
close tolerance shank, short thread in titanium alloy, anodized MoS2 lubricated -
Classification: 1 100 MPa (at ambient temperature)/315 °C - Inch series
Luft- und Raumfahrt - 100° Senk-Passschrauben mit reduziertem Kopf,
Flügelkreuzschlitz, enge Toleranz, kurzes Gewinde, aus Titanlegierung, anodisiert, MoS2
-geschmiert - Klasse: 1 100 MPa (bei Raumtemperatur)/315 °C - Zoll-Reihe
Série aérospatiale - Vis à tête fraisée 100° réduite à empreinte cruciforme déportée avec
fût à tolérance serrée, filetage court en allagie de titane, anodisées, lubrifiées MoS2 -
Classification: 1 100 MPa (à température ambiante)/315 °C - Série en inches
Ta slovenski standard je istoveten z: prEN 6024
ICS:
49.030.20 Sorniki, vijaki, stebelni vijaki Bolts, screws, studs
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2021
ICS 49.030.20
English Version
Aerospace series - Screws, 100° countersunk reduced head
offset cruciform recess close tolerance shank, short thread
in titanium alloy, anodized MoS2 lubricated -
Classification: 1 100 MPa (at ambient temperature)/315
°C - Inch series
Série aérospatiale - Vis à tête fraisée 100° réduite à Luft- und Raumfahrt - 100° Senk-Passschrauben mit
empreinte cruciforme déportée avec fût à tolérance reduziertem Kopf, Flügelkreuzschlitz, enge Toleranz,
serrée, filetage court en allagie de titane, anodisées, kurzes Gewinde, aus Titanlegierung, anodisiert, MoS2-
lubrifiées MoS2 - Classification: 1 100 MPa (à geschmiert - Klasse: 1 100 MPa (bei
température ambiante)/315 °C - Série en inches Raumtemperatur)/315 °C - Zoll-Reihe
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee ASD-
STAN.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 6024:2021 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Requirements . 5
4.1 Configuration — Dimensions — Mass . 5
4.2 Material . 9
4.3 Surface treatment . 9
5 Designation . 9
6 Marking . 9
7 Technical specification . 9
8 Quality management system. 10
Bibliography. 11

European foreword
This document (prEN 6024:2021) has been prepared by the Aerospace and Defence Industries
Association of Europe - Standardization (ASD-STAN).
After enquiries and votes carried out in accordance with the rules of this Association, this Standard has
received the approval of the National Associations and the Official Services of the member countries of
ASD-STAN, prior to its presentation to CEN.
This document is currently submitted to the CEN Enquiry.
1 Scope
This document specifies the characteristics for screws, 100° countersunk reduced head, offset cruciform
recess, close tolerance shank, short thread, in titanium alloy, anodized, MoS lubricated, classification
1 2
1 100 MPa /315 °C , inch series, for aerospace applications.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 2424, Aerospace series — Marking of aerospace products
EN 2491, Aerospace series — Molybdenum disulphide dry lubricants — Coating metho
...